BEAUTURAL
Automatic Foaming Soap Dispenser
User Manual
Please read this user manual carefully before use and keep it for future reference.
[Image: A white automatic foaming soap dispenser with a sleek design, featuring a dispensing nozzle, a liquid level window, and a charging port.]
Cautions
- DO NOT immerse the dispenser in water or rinse it directly with water, or it will cause a short circuit.
- DO NOT use viscous liquids containing granules, powders, emulsions, etc.
- DO NOT tilt or squeeze the liquid bottle when installing the dispenser or replacing the hand soap. However, it is normal for a small amount of soap to come out, and it can be used normally after wiping clean.
- DO NOT invert the dispenser.
- DO NOT block the foam outlet with your hands or foreign objects.
- DO NOT use a charger that does not match this dispenser; otherwise, it will cause the battery to catch fire or explode.
- DO NOT pull the silicone plug too hard when trying to charge the dispenser, as the plug may be damaged and, as a result, will not protect the charging port.
- There is no need to turn the dispenser off if you will continue to use it. It will automatically go into standby when not in use.
- Children should use it under adult supervision to avoid spraying the liquid soap into the eyes or accidental ingestion.
Product Description
[Diagram: Visual representation of the dispenser components labeled:]
- Touch Switch / Indicator
- Foam Outlet
- Sensing Area
- Liquid Viewing Window
- Pipette
- Filter
- Dispenser Body
- Liquid Bottle
- Anti-Slip Bottom
- Waterproof Plug
- Type-C Charging Port
- Accessory: Type-C Cable x1
Compatible Soap Type
- It is recommended to use foaming hand soap directly.
- Liquid soap needs to be diluted with water in a ratio of 1:3. Fill the bottle with the solution and stir evenly.[Diagram: Visual showing 1 part liquid soap mixed with 3 parts water in separate containers, then combined and stirred.]
Note:
- Liquid soap must be diluted and mixed evenly before use; otherwise, it will be too thick and will not foam.
- Do not use soap with solid particles, as it will block the filter.
Operating Instructions
- Charge with the Type-C cable until the white light stays on.
- Rotate and lift up the top cover. [Diagram: Shows rotating and lifting the top of the dispenser.]
- Fill the liquid bottle with 10 fl oz/300 ml of foam hand sanitizer.
- Rotate and lock the top cover. [Diagram: Shows placing the top cover back and rotating to lock it.]
- Touch the switch for 2 seconds; the white light flashes mean to turn it on, and the red light flashes to turn it off.
- Reach towards the sensing area to get the rich foam. Closer to the sensor will result in a small amount of foam with the green light on. Further away will result in more foam with the white light on. [Diagram: Shows hands approaching the dispenser nozzle, illustrating different foam outputs based on proximity and indicator light color.]
- Lather and rub your hands together thoroughly. [Diagram: Shows hands being lathered with foam.]
- Rinse your hands with water. [Diagram: Shows hands being rinsed under water.]
Note:
- The sensitivity of the touch switch may be affected when there is water on it. Therefore, please wipe and clean it before operating.
- When the power is low, the red indicator light will flash three times after sensing, reminding you to charge it.
- When a foreign object blocks the sensing area for more than 5 seconds, the red light will flash continuously. Please turn off the dispenser, wipe the sensing area, and restart it.
Self-Cleaning Function
Quickly press the switch twice when the dispenser is turned on. The blue indicator will flash, and the dispenser will pump continuously for 20 seconds. Pressing the button again will exit the self-cleaning mode.
Cleaning and Maintenance
- Turn off the dispenser and wipe it with a damp towel when cleaning the casing.
- It is recommended to use the dispenser frequently to achieve the best state. Let the sensor induce at least once every half month.
- If you leave the dispenser out for a long time without using it, please clean the tube using the Self-Cleaning Function to avoid blockages:
- Turn off the dispenser, pour the hand soap from the liquid bottle into a cup and save it for later use.
- Clean the liquid bottle completely, add warm water (no more than 50 °C), and install the dispenser.
- Turn on the dispenser, double-press the switch to enter self-cleaning mode, then pour out the remaining water when it is finished. [Diagram: Shows the dispenser running self-cleaning with water.]
- Keep this product in a cool, dry place to avoid humidity and exposure to sunlight and heat.
Troubleshooting
| Issue | Possible Cause | Solution |
|---|---|---|
| It does not turn on. | Low battery power. | Charge the dispenser for 2-3 hours. |
| The indicator does not light up. | It is not turned on. | Press and hold the switch for 2 seconds to turn it on. |
| It does not foam. | The hand soap is depleted. | Refill the liquid bottle. |
| The tube is blocked. | Please check the foam outlet and tube and unclog the tube using the matching soft bottle. | |
| Interference from light. | Move the dispenser to another location to see if the light interferes with the sensor. | |
| The red light will not stop flashing. | Breakdown of the machine. | Contact the seller. |
| Countertop reflection. | Put a black rubber pad under the dispenser. | |
| Something has blocked the sensing area. | Wipe the sensing area, restart the dispenser, and try again. |
Specifications
- Model: 1-JU58NA01
- Capacity: 10 fl oz/300 ml
- Sensing Distance: 0-7 cm
- Rated Voltage: DC 3.7 V 0.65A
- Rated Power: 2.4 W
- Charging Voltage: DC 5 V 0.8A
- Waterproof Level: IPX5
- Single Liquid Output: 1 gram (high-grade) / 0.6 grams (low-grade)
- Soap Type: Foam hand soap and diluted liquid soap with three times the water.
Note: Design and specifications are subject to change without notice.
This product's packaging is made from environmentally friendly material and can be disposed of at your local recycling plant.
Customer Service
UNITED STATES
Phone: +1 909-391-3888 (Mon-Fri 9:00am - 5:00pm PST)
Email: ushelp@1byonebros.com
CANADA
Email: cahelp@1byonebros.com
UNITED KINGDOM
Phone: +44 158 241 2681 (Mon-Fri 9:00am - 6:00pm UTC)
Email: ukhelp@1byonebros.com
GERMANY/ FRANCE/ ITALY/SPAIN
Email: euhelp@1byonebros.com
BRAND OWNER
1byone Products Inc.
1230 E Belmont Street, Ontario, CA, USA 91761
Customer Service: +1 909-391-3888
www.1byonebros.com
1byone Bros | HOME
