Quick Start Guide

Welcome to your BirdBike! This guide will help you assemble your new electric bike quickly and easily.

⏱️ Expect ~30 minute assembly time
? Clear a workspace
⚠️ Do not over tighten screws

Tools Required

• Y-wrench (3mm / 4mm / 5mm)
• L-key Phillips Screwdriver
• 2.5mm Allen key
• Wrench (13mm / 15mm)

Parts Included

• Cap nut and washer (x2)
• Pedals (x2) Left & Right
• Wheel Reflectors (Rear and Front)
• Reflectors and fasteners (x2)
• Battery Keys
• Power Supply and Cable
• Front Fender
• This QSG & User Manual

1. Preparation for Assembly

Unpack all components from the product package, including the Toolkit.

2. Prep the Handlebar Stem

Remove the hex bolt screw from the cardboard tube on the handlebar stem using the 5mm end of the Y-wrench. Set aside the hex bolt for use during installation in step 5.

Discard both the cardboard tube and the black cap that was held in by the hex bolt.

[Tool Required: 5mm Y-wrench]

[Parts Set Aside: Hex bolt]

3. Remove the Dash Display

Gently pull the LED display out from its enclosure within the handlebar. Be careful not to damage any cables.

Remove the screw from under the LED display using the 2.5mm Allen key. Set aside the screw for use during installation in step 11.

[Tool Required: 2.5mm Allen key]

[Part Retrieved: 2.5mm Allen screw]

Tip: If the LED display does not pull out easily, use the 2.5mm Allen key to gently push it out through the screw hole from the back of the handlebar.

4. Install the Handlebars

Aligning the Front Fork (before mounting the handlebars)

Align the fork with the frame so that it is facing forward. The front brake assembly should be on the same side as the kickstand (rider's left side). Ensure the cables are clear and do not restrict the range of motion needed for steering.

5. Attach the Handlebars

Place the handlebar over the handlebar stem and insert the hex bolt (retrieved in step 2) through the handlebar.

Using the 5mm end of the Y-wrench, gently tighten the hex bolt so that there is no play between the fork and frame.

[Tool Required: 5mm Y-wrench]

[Part Retrieved: Hex bolt]

6. Secure the Handlebars

Tighten the two steering stem screws located under the handlebars using the 5mm end of the Y-wrench, ensuring they are securely in place.

[Tool Required: 5mm Y-wrench]

7. Install the Front Wheel

Remove the black fork protector from the bottom of the fork and discard.

Insert the front wheel axle inside of the fork slots. Ensure the brake rotor is aligned to fit inside the front disc brake.

Install washers (serrated side in) and cap nuts onto the outsides of the fork. Tighten them using the 15mm wrench until secure.

Correct tire pressure: 3.5-5.6 bar.

[Tool Required: 15mm Wrench]

[Parts Required: Cap nut and washer x2]

8. Attach the Front Fender

With the 4mm end of the Y-wrench, remove the two screws attached to the back of the fork.

Re-insert these two screws through the holes at the end of the fender-support bracket to secure them onto the fork.

Use the 4mm end of the Y-wrench to remove the screw located on the top of the backside of the fork.

Re-insert this screw through the fender mount bracket on top of the fender and secure tightly to the back of the fork.

[Tool Required: 4mm Y-wrench]

Tip: Ensure the fender is parallel to the wheel to prevent contact as the wheel rotates.

9. Install the Seat

And Adjust the Seat Height

Remove the soft rubber cap located on the frame just below the seat column to reveal the seat clamp screw.

Use the 5mm end of the Y-wrench to loosen the seat clamp screw. Adjust the seat post to the preferred height.

Once positioned, tighten the seat clamp screw until secure and return the rubber cap to the frame.

[Tool Required: 5mm Y-wrench]

Caution: Do not extend the seat post farther than the minimum insertion line indicated on the seat post.

10. Install the Pedals

Screw the left pedal marked "L" counter-clockwise by hand (this pedal is reverse threaded).

Screw the right pedal marked "R" clockwise.

Tighten both pedals with the 15mm wrench.

Each pedal is marked with an "L" or "R" corresponding to the appropriate side on the bolt end and inside of the pedal.

[Tool Required: 15mm Wrench]

[Pedal Markings: L (Left), R (Right)]

11. Reinstall the LED Display

Place the display back into the handlebar enclosure. Be careful not to pinch the cables.

Using the 2.5mm Allen key, reinstall the screw previously removed in step 3 from under the display, ensuring the display fits flush inside the handlebar enclosure.

[Tool Required: 2.5mm Allen key]

[Part Retrieved: 2.5mm Allen screw]

Connect the end of the power cable coming from the bottom of the display to the power cable coming out of the bottom of the frame. Carefully align the arrows on the cables.

12. Charge Battery

Connect the charger: Use the included power supply and connect it to the charging port on the battery (located below the +/- rubber flap).

Finish Charging: When fully charged, a green indicator light on the power supply shows the charge is complete.

The battery can be charged while on the bike or removed for charging.

Please allow 4-6 hours for a full charge.

Tip: Use the battery keys to unlock and charge the battery.

[Indicator: Green light on power supply]

13. Install Reflectors

Rear reflector (red): Wrap the bracket for the rear reflector around the seat post. Secure with a flathead screwdriver. Position the reflector facing rearward.

Front reflector (white): Wrap the bracket for the front reflector around the handlebar near the stem. Secure with a flathead screwdriver. Position the reflector facing forward.

Wheel reflectors: Wrap the bracket for the wheel reflector around any wheel spoke. Secure with a flathead screwdriver.

[Tool Required: Flathead screwdriver (not provided)]

14. Bird App

Download the latest version of the Bird app and sign in or create a new account.

Press the power button on the left handlebar to turn on your Bird Bike.

Find the QR code for your Bird Bike located inside the toolkit or on the front cover of the owner's manual. If you cannot find your code, please contact your retailer.

After pairing, the 'My Bird Bike' screen will appear. This is where you can view the details of your Bird Bike and use its features.

After closing the Bird app, access the 'My Bird Bike' screen through 'Private Birds' in the menu.

[Action: Download Bird app]

[Action: Press power button]

[Information: QR code location]

[App Feature: My Bird Bike screen]

Need Help?

For any questions, concerns, or assistance with assembling the Bird Bike, please reach out directly to Bird. Do not contact the retailer.

Visit: support.bird.co

Email: shopemea@bird.co

[Support Website: support.bird.co]

[Support Email: shopemea@bird.co]