Sonoff Dongle-M Quick Guide V1.2

Introduction

The SONOFF Dongle-M is a Zigbee gateway developed based on ESP32D0WDQ6-V3 and EFR32MG24. It connects Zigbee sub-devices to open-source platforms like Home Assistant and Zigbee2MQTT. It supports PoE (Power over Ethernet) and offers multiple connectivity options, making it adaptable to various usage scenarios.

Through the mDNS domain name, users can access the device's WEB console for operations such as firmware updates and switching between different working modes. Additionally, it integrates powerful features like Webhooks, MQTT, VPN, and a one-click Turbo mode.

Diagram Description: A visual representation of the Dongle-M device, showing its compact form factor with an Ethernet port and a USB-C port. It also depicts common Zigbee devices like smart bulbs and a wall switch, illustrating the gateway's function.

Key Features

• Zigbee 3.0 Gateway
• Supports Thread
• PoE (Power over Ethernet)
• Based on ESP32D0WDQ6-V3 and EFR32MG24
• Compatible with Home Assistant, Zigbee2MQTT, and other open-source platforms
• Webhooks, MQTT, VPN support
• One-click Turbo mode

Setup and Installation

General Setup Steps:

1. Placement: Position the Dongle-M on a flat surface or mount it using the included bracket.
2. Power and Network Connection: Connect the Dongle-M to your network via Ethernet and power it using PoE or a USB-C power adapter.
3. Access Web Console: Access the device's web console via its mDNS domain name or IP address to configure settings and update firmware.

Specific Connection Methods:

• PoE Connection: Connect the Dongle-M to a PoE-enabled switch or injector using an Ethernet cable.
• USB-C Power: Use the included USB-C cable to connect the Dongle-M to a USB power adapter or a computer's USB port for power.

Diagram Description (Page 4): Illustrates connecting the Dongle-M to a computer or power adapter using a USB-C cable. Shows the USB-C port on the Dongle-M.

Diagram Description (Page 5 & 6): Shows how to attach a mounting bracket to the Dongle-M, allowing it to be affixed to surfaces or other equipment.

Diagram Description (Page 7): Depicts the Dongle-M connected to a router via Ethernet and a power source (either PoE or USB-C).

Diagram Description (Page 8): Details the connection of the Dongle-M to a computer using a USB-C cable, emphasizing its use as a USB device.

Diagram Description (Page 9): Illustrates connecting the Dongle-M to a Wi-Fi network, likely through a connected router or access point.

Diagram Description (Pages 10-13): These pages show various physical setup scenarios, including mounting the device, connecting cables, and its integration into a network environment.

Diagram Description (Page 14): Shows the Dongle-M connected to a computer via USB-C, suggesting it can function as a USB dongle.

Accessing the Web Console

After connecting the Dongle-M to your network, you can access its web console to manage the device. The guide suggests accessing it via the mDNS domain name (e.g., dongle-m.local) or by finding its IP address on your network.

Steps to Access:

1. Connect the Dongle-M to your network (Ethernet/PoE).
2. Open a web browser on a device connected to the same network.
3. Enter the device's mDNS name (e.g., dongle-m.local) or its IP address in the address bar. For initial setup or troubleshooting, the URL https://dongle.sonoff.tech/guide/dongle-m/getting-started may be helpful.
4. Follow the on-screen instructions to set up and configure the device.

User Manual: For detailed instructions, users can refer to the full User Manual available at: https://dongle.sonoff.tech/guide/dongle-m/getting-started

Technical Specifications

For CE Frequency:

Under normal use conditions, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

FCC Compliance Statement

Responsible Party: SONOFF TECHNOLOGY LLC
Address: 4777 NE 6th Ave, Suite 201, Bellevue, WA 98007
Email: usres@itead.cc
FCC ID: 2APNS-DONGLEM

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Warnings and Disposal

General Warnings:

• WARNING: This product is not a toy and is not intended for use by children. For adult use only.
• Keep the appliance away from heat and moisture.
• The appliance is suitable for moderate climate only.
• Do not place the appliance near flammable materials such as newspapers, table cloths, curtains, etc.
• Ensure the appliance is placed on a stable surface.

WEEE Disposal (EU):

All products bearing this symbol ♻️ are waste electrical and electronic equipment (WEEE as per directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the EU or the local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity:

Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type Dongle-M is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance

Table: EU Declaration of Conformity Material Types

Environmental Protection (Ochrona Środowiska):

The product contains electronic circuits that are subject to environmental regulations. Dispose of the product according to local regulations for electronic waste.

Symbols:

• CE Marking: The product complies with relevant EU directives.
• FCC Marking: The product complies with FCC regulations.
• Recycling Symbol: Indicates the product is recyclable ♻️.

Manufacturer Information

Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.
Address: 4777 NE 6th Ave, Suite 201, Bellevue, WA 98007, USA
Website: sonoff.tech
Email: support@itead.cc

Made in China