Stinger SPXM1 Marine Digital Media Receiver

Introduction

This document provides installation instructions for the Stinger SPXM1 Marine Digital Media Receiver.

FCC ID: XBD-SPXM1

IC:10801A-SPXM1N

Please read this manual thoroughly before installation. Installation requires technical skill and experience; professional installation by an authorized Stinger or Phoenix Gold Dealer is recommended.

Visit StingerElectronics.com for User Guide, Updates, and Tech Tips.

Precautions ⚠️

• Disconnect the vehicle's negative battery cable before making any wire connections.
• Protect all vehicle surfaces with tape or plastic.
• Do not install components in locations that hinder vehicle operation (e.g., steering wheel, gearshift, air bags, hazard switch).
• Bundle cables and harnesses with electrical tape or wire ties to prevent interference with moving parts.
• Never attempt to disassemble or modify the product; this may result in accident, fire, or electric shock.
• Exposed wires must be insulated with electrical tape to prevent short circuits, fire, or electric shock.
• Confirm locations of hoses, electrical wiring, and the fuel tank before drilling holes to prevent vehicle damage.
• When replacing a fuse, always use one of the correct rating (amperage). Higher amperage fuses may cause a fire.

Parts List

• SOURCE UNIT: The main digital media receiver.
• TRIM PLATE: For fitting the unit into a dashboard opening.
• MOUNTING BRACKET: U-shaped bracket for securing the unit.
• 3.5 X 25 MOUNTING SCREW (4): Screws for securing the unit or bracket.
• M4 X 35 THREADED STUD (2): Studs used with the mounting bracket.
• M4 FLANGE NUTS (8): Nuts to secure the threaded studs.
• POWER / SPEAKER WIRE HARNESS: Connects the unit to the vehicle's power and speakers.

Recommended Tools

• Multimeter
• Wire Strippers
• Wire Cutters
• Drill / Drill Bits
• Phillips Screwdriver
• Wire Crimpers
• Cutting Tool / 3” Hole Saw
• 8mm Wrench (Flange Nuts)
• Battery Terminal Wrench
• Soldering Iron
• Heat Gun

Optional Accessories

Visit StingerElectronics.com for a full line of Marine speakers, amplifiers, lighting, batteries, and accessories.

Mounting Options

The SPXM1 can be mounted using the provided Mounting Bracket or mounting screws.

It is recommended to use both the U Bracket and mounting screws when possible.

A 3" diameter hole is required; a 3" hole saw is recommended.

Mount on a flat surface. Check for obstructions behind the mounting location before cutting.

Ensure adequate space for the radio chassis and wire harness behind the mounting surface.

When using the U Bracket and plastic dash kit, do not overtighten to prevent discoloration of the dash kit.

Using The Mounting Bracket

1. Insert and tighten threaded studs into the back of the radio.
2. Insert the harness and chassis through the mounting hole.
3. Slide the U Bracket onto both studs.
4. Use the supplied nuts to adjust and tighten the bracket.

Wiring & Connections

General Wiring Recommendations

• Solder and heat shrink or waterproof butt connectors are recommended for all wire connections.
• RCA, USB, and Antenna connections should be secured with heat shrink.
• The SPXM1 uses EEPROM memory; there is no (Yellow) wire connected to the battery.
• The Red (ACC 12V+) wire should be connected to switched power, not directly to the battery.
• The Camera/Video Input can be triggered with the Purple/White wire or selected as a Source.

Accessory Control Wiring

The SPXM1 features 4 switchable outputs/triggers (FIG. A) that can control external accessories (e.g., lighting, audio) when used with the optional SPXSH440 Power Bank System.

Switch 1-4 wires are 12V+ outputs and can be activated individually via the ACCESSORY CONTROL source.

WARNING: Accessory control outputs are 100mA. Do not connect directly to accessories or conventional relays. Failure to follow instructions may result in damage and void the warranty.

Wire Connections (Pinout)

Input/Output Connections

• CAMERA/VIDEO INPUT: PURPLE/WHITE or YELLOW wire (Reverse Camera Trigger Input +)
• USB INPUT: USB port
• ANTENNA INPUT: RADIO ANTENNA connector
• LINE OUT (REAR/SUB): RED (Right), WHITE (Left)
• LINE OUT (FRONT): RED (Right), WHITE (Left)
• AUX IN: RED (Right), WHITE (Left)
• WIRED REMOTE: 13-PIN DIN FEMALE connector

Specifications

General

• Operating Voltage: 10-16V DC
• Display: 2.7 inch Color TFT
• Backlit Water Resistant Panel (IPX-6)
• Remote Control: Wired (Optional)

Audio

• Peak Power Output: 45W x 4
• RMS Power Output: 25W x 4
• Speaker Impedance: 4 ohm
• RCA Outputs: 2 Pair (Front, Rear or Sub)
• Preamp Voltage: 2 Volts
• Frequency Response: 20-20kHz
• Equalizer: 7 Band Graphic
• Crossover: High Pass, Low Pass
• Adjustable gain for each source

Tuner

• AM/FM/Weather Bands
• Presets: 18 FM, 12 AM, 6 WB
• Local/Distant Selectable
• Auto Store
• Motorola Antenna Input

USB 2.0

• Location: Rear
• 1 AMP Output
• 32GB Max
• 999 Songs Max
• 255 Folders Max
• File Types: MP3/WMA/WAV

AUX Input

• Location: Rear
• Input Type: Stereo RCA

Camera/Video Input

• Location: Rear
• Input Type: RCA
• Video Format: PAL/NSTC
• External & Internal Trigger

Bluetooth

• Version: 3.0+EDR, A2DP 1.3

Dimensions

• Unit Face: 118mm (4.65in) width, 98mm (3.85in) height
• Chassis Depth: 74mm (2.91in)
• Mounting Hole Diameter: 76mm (3.0in)
• Front Panel Thickness: 21.5mm (0.85in)

Regulatory & Compliance Information

FCC Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The manufacturer is not responsible for radio or TV interference caused by unauthorized modifications or changes to this equipment, as such actions could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction. The FCC Radiation Exposure Statement indicates that the power output is so low that no RF exposure calculation is needed.

IC Statements

This device complies with Industry Canada's licence-exempt RSS standard(s) (RSS-Gen & RSS-247).

Operation is subject to two conditions: (1) the device must not produce interference, and (2) the user must accept any radio interference, even if it may compromise the device's operation.

Attention: Radiofrequency radiation exposure. This equipment complies with Industry Canada's RF exposure limits for an uncontrolled environment and follows the RF exposure guidelines.

Co-location: This transmitter must not be co-located or operated with any other antenna or transmitter.

This Class B digital apparatus complies with Canadian ICES-003.