Pulsar X2 CrazyLight Gaming Mouse
Brand: Pulsar
Product Type: Gaming Mouse
Introduction
This document provides comprehensive information for the Pulsar X2 CrazyLight gaming mouse, covering its features, setup, operation, and support. The X2 CrazyLight is designed for high-performance gaming with advanced features and ergonomic design.
Key Features and Components
Component Identification
The Pulsar X2 CrazyLight mouse features several key components:
- A: ? USB-C Port: For charging and wired connection.
- B: Left Mouse Button
- C: Right Mouse Button
- D: ⚙️ Scroll Wheel
- E: Forward Button
- F: Back Button
- G: ? LED Indicator: Displays status information.
- H: PTFE Feet: Smooth gliding surfaces.
- I: ⚡ Power On/Off Switch
- K: ?️ Optical Sensor: Tracks movement.
Diagrams on page 1 illustrate the top, side, and bottom views of the mouse with these components labeled.
System Requirements
To use the Pulsar X2 CrazyLight, the following system requirements are recommended:
- Intel® Core™ i5 or higher CPU
- AMD Ryzen™ 5 or higher CPU
- USB 3.0 or Higher Port
Page 2 shows a diagram illustrating the connection between the mouse, the 8K Wireless Dongle, and a computer via a USB 3.0 port.
Connectivity and Dongle
The mouse supports 8K Wireless Dongle connectivity. For stable performance, the dongle should be positioned within 50cm (19.6 inches) of the mouse, ensuring no obstacles are present between them. The dongle connects via a USB 3.0 or higher port.
LED Indicator Status
The LED indicator on the mouse provides status updates:
Wireless Mode:
- Red Blinking: Low Battery (below 30%). Please charge.
- Yellow Blinking: Mouse Pairing Mode.
Wired Mode:
- Steady Red: Charging.
- Steady Blue: Fully Charged.
Page 2 provides visual examples of these LED states.
DPI Settings
The DPI (Dots Per Inch) can be adjusted to fine-tune cursor sensitivity. The default DPI is 800, with a maximum adjustable DPI of 32,000.
- DPI Indication: When changing DPI, the LED indicator will blink three times in the designated color (e.g., Blue for 800 DPI default).
- Software Adjustment: DPI can be set between 50 and 32,000 DPI using the Pulsar software.
- Fine-Tuning: The software allows DPI values to be adjusted in increments of 10.
Page 5 shows a color chart for DPI indication and details on software-based DPI adjustment and fine-tuning.
Polling Rate
The polling rate determines how often the mouse reports its position to the computer. The X2 CrazyLight supports polling rates from 125Hz up to a maximum of 8KHz (8000Hz).
Available polling rates include: 125, 250, 500, 1K (1000Hz), 2K (2000Hz), 4K (4000Hz), and 8K (8000Hz).
Page 4 lists the available polling rate options.
Lift-Off Distance (LOD)
The Lift-Off Distance (LOD) is the height at which the mouse sensor stops tracking when lifted from a surface. Using the Pulsar software, the LOD height can be set to 0.7mm, 1mm, or 2mm.
Page 5 illustrates the different LOD height options.
Usage and Setup
Dongle Pairing
To pair the wireless dongle with the mouse:
- Press and hold the buttons as indicated in the diagram for 3 to 4 seconds.
- The LED indicator will blink yellow, indicating pairing mode.
Page 3 shows a diagram illustrating the button presses for dongle pairing.
LED On/Off Control
You can control the LED indicator's on/off state:
- Press and hold buttons 1, 2, and 3 simultaneously for 5 seconds to adjust the LED On/Off state.
Page 3 provides a diagram showing the buttons to press for LED control.
Dot Skates Installation
To install the included UHMW-PE dot skates:
- Remove any existing skates from the mouse.
- Clean the mouse surface where the skates will be applied, ensuring no residue remains.
- Align and attach the UHMW-PE skates to the mouse, matching them to the designated areas or grooves.
- Press the skates firmly with your fingers to ensure they are securely attached.
Page 6 provides a step-by-step visual guide for installing the dot skates.
Support and Warranty
Safety Information
Please read the manual before using the product. Key safety guidelines include:
- Do not open or modify the product, as this will void the warranty.
- Avoid directing the laser beam at eyes or reflective objects.
- Do not immerse the product in liquids or expose it to extreme heat or moisture.
- If the product is exposed to out-of-range temperatures, power it off until stable.
- This product is not intended for use by children under 14 years old.
- Contact Pulsar Support if the product is not operating properly.
Warranty
Pulsar offers a 2-year limited warranty from the date of original retail purchase, covering defects in materials and workmanship. For detailed warranty information, please visit the Pulsar website.
Website: www.pulsar.gg/warranty
Contact Information
For any questions, comments, or assistance with your Pulsar products, please contact Pulsar Support.
- Global Support: www.pulsar.gg/support
- Korea Support: support@pulsargg.kr
- Japan Support: support@pulsargg.jp
Page 8 features a graphic encouraging users to join the Pulsar Discord Community and provides contact details.
