i-tec MYSAFE USB-C / USB 3.0 2X M.2 SSD RAID EXTERNAL CASE

Product Overview

This document provides instructions for the i-tec MYSAFE USB-C / USB 3.0 2X M.2 SSD RAID External Case. It supports two M.2 B-Key SATA SSDs and offers RAID 0, JBOD, and RAID 1 configurations.

Specifications

• External USB-C case for 2x M.2 B-Key SATA Based SSD disks
• Transmission interface: 1x USB-C, Gen 2
• Compatible with M.2 B-Key SATA Based SSD disks with sizes of 2230, 2242, 2260, 2280
• Backward compatible with USB 3.0/2.0 interface via the included USB-C to USB 3.0 cable
• Supports Plug & Play function
• Active LED diodes indicate the case state: solid light for connected, flashing for writing/reading in progress
• RAID field switch
• Power supply: 5V, 900mA
• Weight: 165 g
• Dimensions: 125 x 78 x 20 mm

System Requirements

• Operating Systems: Windows 7/8/8.1/10 32/64bit, macOS 10.x and higher
• Automatic driver installation from the system
• Requires a free USB-C or USB-A port

Hardware Installation

1. Slide out the inner part with the motherboard.
2. Insert M.2 disks, aligning the disk's cutout with the M.2 connector. Screw the M.2 disks to the motherboard from the opposite side.
3. Set the RAID field using the RAID field switch (refer to RAID Field Setting section).
4. Slide the assembled unit back into the case and screw it from the bottom.
5. Attach the rubber feet to the bottom of the case.
6. Connect the USB-C or USB-C/A cable to the case and the computer.
7. Switch the ON/OFF switch to the ON position.
8. The device will be detected and automatically installed.
9. The device is now ready for use.

RAID Field Setting

Note: Changing RAID settings will erase any previously saved data.

Use the switch to select one of four connection options for the disks based on your needs:

• A) RAID 0 (Stripping/Striping): Data is written to both disks simultaneously and interleaved. Offers high read/write speed. Warning: Data loss occurs if one disk fails.
• B) JBOD (Separate Disks): Disks are reported as two separate drives in the system. The LED flashes based on the disk being written to.
• C) JBOD (Capacity Sum): Disks are reported as a single drive with the combined capacity of both inserted disks. Writing is sequential (one disk then the other). The LED flashes based on the disk being written to.
• D) RAID 1 (Mirroring): Data is duplicated across both disks. Both LEDs flash during writing, and only one LED flashes during reading. Data is not lost if one disk fails.

After connecting and powering on the case, press and hold the Reset button for 5 seconds to apply new RAID settings. Then, format the disks.

Power Supply

If the case is not sufficiently powered via the USB-C port, it is recommended to connect an external 5V power source (not included in the package).

Software Installation

Upon connecting the device to a computer (Windows 7/8/8.1/10 32/64bit or macOS 10.x and higher), the system will automatically detect and install the necessary drivers.

Note: The case surface may become warm during operation. This is normal and helps cool the internal electronics. Avoid covering the case.

New HDD Formatting

For correct device operation, new disks must be formatted. If a disk was previously used, formatting may not be necessary. Formatting will erase all existing data.

1. Right-click on "My Computer" (or "This PC").
2. Select "Manage".
3. Click on "Disk Management".
4. Select the HDD identified as "Unallocated" or "Uninitialized" with the inserted disk's capacity (capacity may appear slightly lower).
5. If the disk is not initialized, right-click in the left pane and select "Initialize Disk".
6. Right-click on the disk area and select "New Simple Volume", then click "Next".
7. Leave the volume size at maximum and click "Next".
8. Assign a drive letter and click "Next".
9. Select "Format the volume with the following settings" (use default settings), click "Next", and then "Finish".
10. The HDD will be formatted. Formatting time depends on HDD size. The HDD will then be visible in the system.

Recommendation: Save important or valuable data on multiple disks or other storage media.

Package Content

• External case for M.2 disk
• USB-C cable – 45cm length
• USB-C to USB 3.0 cable – 45cm length
• Screwdriver
• Screws
• Rubber feet
• User manual

Frequently Asked Questions

FAQs are available on the i-tec website at www.i-tec.cz/en/ under the "FAQ" tab.

Compliance Information

WEEE Directive

This equipment is marked with the recycling symbol, indicating it must be disposed of separately at an appropriate collection point at the end of its life, not with unsorted domestic waste. This helps protect the environment. (European Union only).

EU Declaration of Conformity

Manufacturer: i-tec Technologies s.r.o. declares that this product (i-tec MYSAFE Metal M.2 DUAL RAID External Case USB-C 3.1 Gen 2 for 2x M.2 SATA based B-Key SSD, Model: CAMYSAFEDUALM2) is determined for use in PC as equipment and meets essential requirements according to EC Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and 2009/125/ES.

Compliance with EMC standards (EN 55032:2015/AC2016-07, EN 61000-3-2:2014, EN 61000-3-3:2013, EN 55024:2015, IEC 61000-4-2:2009, EN61000-4-3:2006+A2:2010) and safety standards (EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013) is confirmed.

RoHS compliance: 2011/65/EU; EU 2015/863.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.