Joyroom JR-ZS291 Magnetic Wireless Car Charger Holder
User Manual
Product Overview
Product Name: Joyroom JR-ZS291 Magnetic Wireless Car Charger Holder
Product Material: ABS+PC
Applicable Phone Size: 4.7-6.7 inches
Input Port: Type-C
Indicator Light:
- Power on: Crystal edge light turns on
- Standby: Constant crystal edge light
- Charging: Crystal edge light turns off
- FOD (Foreign Object Detection): Flashing crystal edge light
Visual Description: The product is a round, circular device with a crystal-like edge that illuminates. It features a Type-C input port and an air vent clip hook for mounting.
Parameters
| Parameter | Details |
|---|---|
| Model | JR-ZS291 |
| Name | Magnetic Wireless Car Charger Holder |
| Material | ABS+PC |
| Input | 5V-2A, 9V-2A, 12V-1.5A |
| Output | 5W/7.5W/10W/15W (MAX) |
| Input Port | Type-C |
| Applicable Phone Size | 4.7-6.7 inches |
Installation and Operation
- Mounting the Holder: Insert the ball head into the nut, then into the socket on the back of the holder. Tighten the nut clockwise.
- Attaching to Air Vent: Loosen the knob, open the hook, insert the hook onto the vent blade, and then tighten the knob to secure it.
- Connecting Power: Use the provided Type-C charging cable to connect the holder to a car charger (QC3.0 compatible charger recommended).
- Placing Your Phone: Place your phone near the holder. It will be securely attached and begin charging due to its magnetic and auto-alignment functions.
Note: For iPhone 12/13 series, it is recommended to use magnetic phone cases if you wish to use a case while charging.
Warnings
- Do not disassemble or modify the product.
- Avoid storing the product in wet environments.
- Keep the product away from heat sources and do not charge near them.
- Prevent water or other liquids from entering the product interface to avoid damage.
- Do not install the wireless car charger holder over an airbag cover or within the airbag deployment zone.
- During charging, remove metallic/magnetic protective cases or cards (like bank cards) from your device.
- The charger may heat up during charging; this is normal. If the charger or phone becomes too hot, disconnect power and let it cool before restarting.
- Avoid using bent or damaged USB cables.
Warranty Information
Joyroom provides a 12-month free warranty service for performance failures not caused by human error, starting from the date of purchase.
Warranty Exceptions:
- Human damage.
- Exceeding the warranty period.
- Failure to provide valid proof of purchase.
- Product damage due to failure to follow usage, maintenance, or storage instructions.
- Product damage caused by unauthorized disassembly, repair, or immersion in water.
- Damage caused by force majeure.
Note: Please contact the distributor for warranty service. Keep the warranty card and invoice for service.
Warranty Card
Model: JR-ZS291
Purchase Date:
Distributor:
Customer Name:
Tel:
Invoice Date:
User address (with postcode):
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
