Honeywell Lyric™ C1 Wi-Fi Security Camera

Download the Honeywell Lyric app

NOTE: Have your Wi-Fi password available and confirm your router communicates at 2.4 GHz before installation.

1. Make sure [Bluetooth] is enabled on your mobile device.
2. Search for Honeywell Lyric in the App Store or Google Play.
3. Download the Honeywell Lyric app.

[App Store] [Google Play]

Installation

Launch the Lyric app

1. Launch the Lyric app.
2. Select the Lyric C1 Wi-Fi Camera to install, then create an account (if necessary), or sign in to your Lyric account.
3. Follow the instructions in the Lyric app to name the camera and its location.

Connect the power cord

1. Remove the camera base and plug the power cord's USB end into the camera.
2. Reinsert the camera base and plug the camera into a power outlet.
3. Wait until the [LED indicator] on the camera blinks blue (about 1 minute), then tap NEXT.

NOTE: If the [LED indicator] turns solid red, it means the connection mode timed out. Unplug the camera and plug it back in.

Connect

Connect to mobile device

1. Enable [Bluetooth] on your mobile device.
2. The app will look for the camera.
   • For one camera, it will connect automatically.
   • For more than one camera, the app will prompt you to select one camera at a time. Each camera has a unique MAC ID printed on the back. Use that ID to select the camera you want to connect.
3. A [QR code] will display in the app. To connect your camera to the app, hold the [QR code] approximately 3-8 inches (7-20 cm) from the camera lens.
4. The camera [LED indicator] turns purple and the camera beeps.

Connect to Wi-Fi

NOTE: Be sure you are on the same [Wi-Fi] network you wish to connect your camera to.

1. Choose your [Wi-Fi] network from the list. Tap NEXT.
2. Enter your [Wi-Fi] password, if necessary. Tap DONE.

NOTE: The camera will beep during some steps in this process.

Wi-Fi connection LEDs

Placement

With stand

Place the camera in a desired location for viewing and recording.

On the wall

You can also mount the camera directly to the wall without the stand.

Operation

Remove/replace the stand

The stand is connected to the camera by a magnet. If you want to remove the stand to hang the camera on the wall or replace the SD card, simply pull the stand off of the camera. To replace, just snap it back on the camera.

Lyric app experience

When you launch the application, live video from your camera is displayed. If you have multiple cameras, a list of them is displayed. Select a camera from the list to view live video from that camera.

Testing smoke/CO alarm detection

If your smoke or carbon monoxide alarm goes off and your camera is on, it will send you an alert that a smoke or CO alarm has been detected. To test this feature, press and hold the Test button on your smoke/CO detector for at least 5 seconds or 3 cycles of the detector's alarm. A shorter test might not trigger a sound event.

Camera overview

Camera lens

LED indication

Power cord

Stand

Reset hole

SD card and slot

Reset

If your [Wi-Fi] connection fails or you need to connect to a different [Wi-Fi] network, insert one end of a [paperclip] into the reset hole. Press and hold it for 5 seconds to reset the [Wi-Fi] connection. To reset all settings to factory defaults, press and hold the [paperclip] in the reset hole for 10 seconds.

SD card

The camera comes with an encrypted 8GB SD card installed. It stores images if the camera's connection to the cloud is lost. You can replace it with any compatible SD card.

Status LED

FCC Regulations

§ 15.19 (a)(3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

IC Regulations

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Need help?

• Web: yourhome.honeywell.com
• Email: MyLyric@honeywell.com
• Phone: 1-800-633-3991