Sure Cross® DXM150-S2 Wireless Modbus Slave

Datasheet

The DXM150-S2 Wireless Modbus Slave can connect directly to an RS-485 serial bus or to a wireless ISM network as a remote Modbus Slave device.

• Power options include 12 to 30 V DC with or without a battery backup, or 12 V DC solar panel with a sealed lead acid battery.
• Local I/O options: isolated discrete inputs, universal inputs, NPN/PNP outputs, analog outputs (0 to 10 V), and courtesy power.
• ISM radios available in either a 900 MHz band or 2.4 GHz band for local wireless networks.

Important: Please download the complete DXM150-S2 Wireless Modbus Slave technical documentation, available in multiple languages, from www.bannerengineering.com for details on the proper use, applications, Warnings, and installation instructions of this device.

Important: Por favor descargue desde www.bannerengineering.com toda la documentación técnica de los DXM150-S2 Wireless Modbus Slave, disponibles en múltiples idiomas, para detalles del uso adecuado, aplicaciones, advertencias, y las instrucciones de instalación de estos dispositivos.

Important: Veuillez télécharger la documentation technique complète des DXM150-S2 Wireless Modbus Slave sur notre site www.bannerengineering.com pour les détails sur leur utilisation correcte, les applications, les notes de sécurité et les instructions de montage.

WARNING:

• Do not use this device for personnel protection. Using this device for personnel protection could result in serious injury or death.
• This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.

Important:

• Never operate a 1 Watt radio without connecting an antenna. Operating 1 Watt radios without an antenna connected will damage the radio circuitry.
• To avoid damaging the radio circuitry, never apply power to a Sure Cross® Performance or Sure Cross MultiHop (1 Watt) radio without an antenna connected.

Important:

• Electrostatic discharge (ESD) sensitive device. ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and assembling units on a grounded, static-dissipative surface.

Model Key for the DXM150-S2 Models

Base Description (S2):

Modbus slave with high I/O count for MultiHop wireless networks or wired networks.

• Power: 12-30 V DC/Solar/Battery
• Comms: RS-485
• Inputs: (2) Isolated discrete, (8) Universal
• Outputs: (8) PNP/NPN Selectable, (2) Analog
• Power Out: (2) Courtesy power out; (2) Jumper selectable between 2.7 V or battery, 4.2 V or incoming power

Radio Configuration Options:

• Blank: None
• R2: 900 MHz, 1W HE5 MultiHop Data Radio (North America)
• R4: 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)
• R5: 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)
• R9: 900 MHz, MultiHop Radio approved for Australia/New Zealand

Some example models include, but are not limited to, the following:

Original Document: 200634 Rev. I, 26 March 2020

DXM150 Documentation List

• DXM Wireless Controller Sell Sheet, p/n 194063
• DXM150-B1 Wireless Controller Datasheet, p/n 178136
• DXM150-B2 Wireless Controller Datasheet, p/n 195952
• DXM150-Bx Wireless Controller Instruction Manual, p/n 190038
• DXM150-S1 Modbus Slave Datasheet, p/n 160171
• DXM150-S2 Modbus Slave Datasheet, p/n 200634
• DXM150-Sx Modbus Slave Instruction Manual, p/n 195455
• DXM Controller Configuration Quick Start, p/n 191247
• DXM Controller API Protocol, p/n 186221
• DXM ScriptBasic Instruction Manual, p/n 191745
• DXM Configuration Software v4 (p/n b_4496867)
• DXM Configuration Software v4 Instruction Manual, p/n 209933
• DXM EDS Configuration file for Allen-Bradley PLCs
• EIP Configuration File for DXM 1xx-BxR1 and R3 models (p/n 194730)
• Activating a Cellular Modem (p/n b_4419353)
• Additional technical notes and videos

For more information about the DXM family of products, including technical notes, configuration examples, and ScriptBasic programs, please visit www.bannerengineering.com/wireless.

DXM150-S2 Wireless Modbus Slave System Overview

Banner's DXM Logic Controller integrates Banner's wireless radio and local I/O for a remote I/O device.

Inputs/Outputs

On-board universal and programmable I/O ports connect to local sensors, indicators, and control equipment.

• Universal Inputs
• Discrete outputs
• Courtesy power
• Switch power
• Isolated inputs
• Battery backup
• Solar controller

Connectivity

The integrated Sure Cross® wireless radio enables Modbus connectivity to remote sensors, indicators, and control equipment.

Wired Connectivity

Field Bus: Modbus RS-485 Master

Wireless Connectivity

Sure Cross MultiHop 900 MHz, or MultiHop 2.4 GHz

Specifications

MultiHop Radio Specifications

Radio Range¹

• 900 MHz, 1 Watt: Up to 9.6 km (6 miles)
• 2.4 GHz, 65 mW: Up to 3.2 km (2 miles)

Antenna Minimum Separation Distance

• 900 MHz, 150 mW and 250 mW: 2 m (6 ft)
• 900 MHz, 1 Watt: 4.57 m (15 ft)
• 2.4 GHz, 65 mW: 0.3 m (1 ft)

Radio Transmit Power

• 900 MHz, 1 Watt: 30 dBm (1 W) conducted (up to 36 dBm EIRP)
• 2.4 GHz, 65 mW: 18 dBm (65 mW) conducted, less than or equal to 20 dBm (100 mW) EIRP

Spread Spectrum Technology

FHSS (Frequency Hopping Spread Spectrum)

900 MHz Compliance (1 Watt)

FCC ID UE3RM1809: FCC Part 15, Subpart C, 15.247

IC: 7044A-RM1809

IFT: RCPBARM13-2283

2.4 GHz Compliance (MultiHop)

FCC ID UE300DX80-2400: FCC Part 15, Subpart C, 15.247

Radio Equipment Directive (RED) 2014/53/EU

IC: 7044A-DX8024

Antenna Connection

Ext. Reverse Polarity SMA, 50 Ohms

Max Tightening Torque: 0.45 N·m (4 lbf-in)

Radio Packet Size (MultiHop)

• 900 MHz: 175 bytes (85 Modbus registers)
• 2.4 GHz: 75 bytes (37 Modbus registers)

¹ Radio range is with the 2 dB antenna that ships with the product. High-gain antennas are available, but the range depends on the environment and line of sight. Always verify your wireless network's range by performing a Site Survey.

RS-485 Communication Specifications

Communication Hardware (MultiHop RS-485)

• Interface: 2-wire half-duplex RS-485
• Baud rates: 9.6k, 19.2k (default), or 38.4k via DIP switches; 1200 and 2400 via the MultiHop Configuration Software
• Data format: 8 data bits, no parity, 1 stop bit

Power and I/O Specifications

Supply Voltage

• 12 to 30 V DC (use only with a suitable Class 2 power supply (UL) or a SELV (CE) power supply) or 12 V DC solar panel and 12 V sealed lead acid battery

Power Consumption

• 20 mA average at 12 Volts (exclusive of load)

Solar Power

• 12 V sealed lead acid battery
• 2 A maximum charge current
• 12 V, 20 W maximum solar panel

Solar Power Battery Charging

• 1 A maximum with 20 Watt solar panel

Universal Inputs

• Sinking/Sourcing discrete, 4-20 mA analog, 0-10 V analog, counter, and temperature
• 10 kOhm thermistor
• Counters, Synchronous
• 32-bits unsigned
• 10 ms clock rate minimum

Discrete Inputs

• Optically isolated AC input type
• Input to output isolation: 2.5 kV

Analog Outputs (DAC)

• 0 to 20 mA or 0 to 10 V DC output
• Accuracy: 0.1% of full scale +0.01% per °C
• Resolution: 12-bit

Courtesy Power Out

• Two incoming power or battery power
• 100 mA maximum

Selectable (Jumper) Power Out

• Output on pin 45, jumper selects 2.7 V or battery
• Output on pin 35, jumper selects 4.2 V or incoming power
• 100 mA maximum

Communication Protocol

Modbus RTU Slave

Construction

Polycarbonate; DIN rail mount option

Indicators

Four LEDs, four control buttons, one LCD

Discrete Outputs

• Eight sourcing/PNP, sinking/NPN
• ON Condition: Supply minus 2 V
• OFF Condition: Less than 2 V

Discrete Output Rating (PNP)

• 100 mA max current at 30 V DC
• ON-State Saturation: Less than 3 V at 100 mA
• OFF-state Leakage: Less than 10 μΑ

Discrete Output Rating (NPN)

• 100 mA max current at 30 V DC
• ON-State Saturation: Less than 1.6 V at 100 mA
• OFF-state Leakage: Less than 200 µA for loads greater than 3 ΚΩ. For load current of 100 mA, leakage is less than 1% of load current.

Environmental Specifications

Operating Conditions²

• -20 °C to +60 °C (-4 °F to +140 °F)
• 95% maximum relative humidity (non-condensing)
• Radiated Immunity: 10 V/m (EN 61000-4-3)

Shock and Vibration

• All models meet IEC 60068-2-6 and IEC 60068-2-27 testing criteria
• Shock: 15G 11 ms duration, half sine wave per IEC 60068-2-27
• Vibration: 10 Hz to 55 Hz, 0.5 mm peak-to-peak amplitude per IEC 60068-2-6

Environmental Rating

IEC IP20

Certifications

• CE (CE approval only applies to 2.4 GHz models)
• CULUS LISTED
• NOM (NOM approval only applies to 900 MHz models)
• NYCE

Required Overcurrent Protection

WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations.

Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to www.bannerengineering.com.

Accessories

For a complete list of all the accessories for the Sure Cross wireless product line, please download the Accessories List (p/n b_3147091).

Cordsets

• MQDC1-506-5-pin M12/Euro-style, straight, single ended, 6 ft
• MQDC1-530-5-pin M12/Euro-style, straight, single ended, 30 ft
• MQDC1-506RA-5-pin M12/Euro-style, right-angle, single ended, 6 ft
• MQDC1-530RA-5-pin M12/Euro-style, right-angle, single ended, 30 ft

Static and Surge Suppressor

BWC-LFNBMN-DC-Surge Suppressor, bulkhead, N-Type, dc Blocking, N-Type Female, N-Type Male

Short-Range Omni Antennas

• BWA-202-D-Antenna, Dome, 2.4 GHz, 2 dBi, RP-SMA Box Mount
• BWA-902-D-Antenna, Dome, 900 MHz, 2 dBi, RP-SMA Box Mount
• BWA-902-RA-Antenna, Rubber Fixed Right Angle, 900 MHz, 2 dBi, RP-SMA Male Connector

Medium-Range Omni Antennas

• BWA-905-C-Antenna, Rubber Swivel, 900 MHz 5 dBi, RP-SMA Male Connector
• BWA-205-C-Antenna, Rubber Swivel, 2.4 GHz 5 dBi, RP-SMA Male Connector

Long-Range Omni Antennas

• BWA-908-AS-Antenna, Fiberglass, 3/4 Wave, 900 MHz, 8 dBi, N-Type Female Connector
• BWA-208-A-Antenna, Fiberglass, 2.4 GHz, 8 dBi, N-Type Female Connector

Long-Range Yagi Antennas

• BWA-9Y10-A-Antenna, 900 MHz, 10 dBd, N-Type Female Connector

Cellular Antenna

BWA-CELLA-002-Cellular multiband, 2 dBi, RP-SMA male connection, 6.3 inch blade style. Datasheet: b_4475176

Misc Accessories

• BWA-CG.5-3X5.6-10-Cable Gland Pack: 1/2-inch NPT, Cordgrip for 3 holes of 2.8 to 5.6 mm diam, 10 pack
• BWA-HW-052- Cable Gland and Vent Plug Pack: includes 1/2-inch NPT gland, 1/2-inch NPT multi-cable gland, and 1/2-inch NPT vent plug, one each
• BWC-1MRSMN05-LMR200 RP-SMA to N-Type Male, 0.5 m
• BWC-2MRSFRS6-LMR200, RP-SMA Male to RP-SMA Female Bulkhead, 6 m
• BWC-4MNFN6-LMR400 N-Type Male to N-Type Female, 6 m

² Operating the devices at the maximum operating conditions for extended periods can shorten the life of the device.

Enclosures and DIN Rail Kits

• BWA-AH864-Enclosure, Polycarbonate, with Opaque Cover, 8 x 6 x 4
• BWA-AH1084-Enclosure, Polycarbonate, with Opaque Cover, 10 x 8 x 4
• BWA-AH12106-Enclosure, Polycarbonate, with Opaque Cover, 12 x 10 x 6
• BWA-AH8DR-DIN Rail Kit, 8", 2 trilobular/self-threading screws
• BWA-AH10DR-DIN Rail Kit, 10", 2 trilobular/self-threading screws
• BWA-AH12DR-DIN Rail Kit, 12", 2 trilobular/self-threading screws

Power Supplies

• PSD-24-4-DC Power Supply, Desktop style, 3.9 A, 24 V dc, Class 2, 4-pin M12/Euro-style quick disconnect (QD)
• PSDINP-24-13-DC power supply, 1.3 Amps, 24 V DC, with DIN Rail Mount, Class I Division 2 (Groups A, B, C, D) Rated
• PSDINP-24-25-DC power supply, 2.5 Amps, 24 V DC, with DIN Rail Mount, Class I Division 2 (Groups A, B, C, D) Rated
• BWA-SOLAR PANEL 20W-Solar Panel, 12 V, 20 W, Multicrystalline, 573 x 357 x 30, "L" style mounting bracket included (does not include controller)

Warnings

Install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna configurations installed without surge suppressors invalidate the manufacturer's warranty. Keep the ground wire as short as possible and make all ground connections to a single-point ground system to ensure no ground loops are created. No surge suppressor can absorb all lightning strikes; do not touch the Sure Cross® device or any equipment connected to the Sure Cross device during a thunderstorm.

Exporting Sure Cross® Radios. It is the intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers who want to re-export this product to a country other than that to which it was sold must ensure the device is approved in the destination country. The Sure Cross wireless products were certified for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding the transmit power levels allowed by local governing agencies. This device has been designed to operate with the antennas listed on Banner Engineering's website and having a maximum gain of 9 dBm. Antennas not included in this list or having a gain greater that 9 dBm are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen such that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. Consult with Banner Engineering Corp. if the destination country is not on this list.

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. For patent information, see www.bannerengineering.com/patents.

Notas Adicionales

Información México: La operación de este equipo está sujeta a las siguientes dos condiciones: 1) es posible que este equipo o dispositivo no cause interferencia perjudicial y 2) este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

Banner es una marca registrada de Banner Engineering Corp. y podrán ser utilizadas de manera indistinta para referirse al fabricante. "Este equipo ha sido diseñado para operar con las antenas tipo Omnidireccional para una ganancia máxima de antena de 6 dBd y Yagi para una ganancia máxima de antena 10 dBd que en seguida se enlistan. También se incluyen aquellas con aprobación ATEX tipo Omnidireccional siempre que no excedan una ganancia máxima de antena de 6dBd. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que 6 dBd en tipo omnidireccional y 10 dBd en tipo Yagi, quedan prohibidas. La impedancia requerida de la antena es de 50 ohms."

Antenas SMA

Antenas Tipo-N

Mexican Importer

Banner Engineering de Mèxico, S. de R.L. de C.V.

David Alfaro Siqueiros 103 Piso 2 Valle oriente

San Pedro Garza Garcia Nuevo Leòn, C. P. 66269

81 8363.2714

BANNER - more sensors, more solutions

Banner Engineering Corp. All rights reserved