User Manual for Tuya DIY models including: Smart WIFI IR Digital Music Lines Kit, Smart WIFI IR, Digital Music Lines Kit, Music Lines Kit, Digital Music Kit
SHEN ZHEN CL LIGHTING TECHNOLOGY CO.,LTD FWWSA8-23-18 Tuya DIY Smart WIFI IR Digital Music Lines Kit 2AUEP-FWWSA8-23-18 2AUEPFWWSA82318 fwwsa8 23 18
File Info : application/pdf, 3 Pages, 561.79KB
DocumentDocumentUser Manual
Tuya DIY Smart WIFI+IR Digital Music Lines Kit
Features
DIY intelligent splicing scheme, which can be spliced according to customer needs.
Cool lighting effects, colorful, flowing water, rainbow, Ambilight and other transformation modes.
WIFI+BLE+IR protocol with APP+Remoter control.
Styling reference
12V low-voltage power supply, and uses any single product as the power supply for the overall shape. Classic appearance and compact structure. It can be spliced with different shapes and is easy to install.
Parameters
Model
Colour Voltage Power
Control
Parts List
FWWSA8-23-6
RGBIC
DC12V
10W
Remoter+control
Adapter x 1 3M glue x 13 Connector x 8
Manual x 1 screw x 8
Remote Controller x 1
FWWSA8-23-9
RGBIC
DC12V
14W
Remoter+control
Adapter x 1 3M glue x 19 Connector x 11 Manual x 1 screw x 11 Remote Controller x 1
FWWSA8-23-12
RGBIC
DC12V
18W
Remoter+control
Adapter x 1 3M glue x 25 Connector x 14 Manual x 1 screw x 14 Remote Controller x 1
Product function diagram
Product Size
Single click to switch ON Double click to switch OFF Single click mode Long press for 5 seconds to reset
Music Mode
Brightness
Plug Connector
5;: 5;:
Installation Instructions
1: Unpack the package and check whether the appearance is intact, and whether the number of accessories is correct:
Figure Remove the protective cover of the controller and the lamp INinterface, and then install the connector of the controller The connector is aligned with the OUT of the controller.The bumps are aligned with one end of the single notch of the connector. (Bump to Notch) Figure (The yellow slant of the connector clip and the orange slant of the controller are close to each other and then pressed down diagonally). Note: Press down on the side of the suspension to remove a single connector.
When two lamps are connected together, grab one lamp and lift it up to remove it, and then remove the single connector.
3: Take out the first one according to the shape, install connectors on both sides, and deduct the OUT direction to connect position the protective cover, then take out the connector to connect one end of the single notch of the clip is connected to one end of the lamp OUT. (Bump to Notch) (The yellow slope in the diagram of the connector buckle and the orange slope on the controller are close to each other, and then press down diagonally.) Figure Attach the connector at one end of the two notches in the IN direction with same way.
/4
5: The second one of the modeling starts, just install the connector on the OUT port, and tear off the red centrifugal paper on the lamp. When installing, the width of the lamp should be aligned with the previous lamp, and the inclined surface of the IN interface of the lamp should be aligned with the inclined surface of the buckle, and then press down firmly. Figure s Refer to Figure S to see if screw reinforcement is required, and install the remaining few in the same way. The last part of the shape does not need to buckle the protective cover, and does not need to install the connector.
5;: /4
6
5;:
5;:
8
9
1
2
2: In the same way, align the IN-port of the lamp to connect, plug in the adapter to light up, and test each one. Figure Take out the double-sided adhensive,
tear off one side of the white centrifugal paper, and stick it to the square position on the back of the lamp(controller). Figure And design the shape and place it according to your own preferences. Figure Check if there is a problem
with the lamp. Pay attention to the running mode of the light, which is related
to the position of the controller. It is recommended that the controller be
designed in the head position.
4: Determine a position according to the shape, tear off the double-sided adhesive red centrifugal paper on the lamp, align the adhesive surface on the wall to be installed, press hard and install the first piece, and then install the rest according to the shape. Determine whether to use screws for reinforcement according to the user's usage scenario. The reinforcement position is as shown in the figure. At the middle oval hole of the buckle, the whole set needs to be reinforced, and the user decides by himself. Figure S
Note: (one inlet, three outlets) - the OUT port of the lamp must be connected to the IN port of the next lamp.
6: Finally, tear off the double-sided tape of the controller, buckle the connector,
and install the controller on the connector of the first head. Installation is complete. Figure Plug the adapter into the DC socket of the controller and start the experience. Figure
3
4
5
7
10
Notes:
Please choose a dry, clean and smooth surface for installation, the following conditions should not be used: Do not use double-sided tape for fixing in humid or low temperature environments (such as bathrooms, toilets, etc.) Do not install this product on the ceiling to prevent it from falling (the double-sided tape is not sticky enough to stick this product firmly on the ceiling) Do not use double-sided tape on brick walls, rough walls, frosted glass, wall coverings with wallpaper, dusty walls, rough plastic surfaces and other uneven walls. Users can decide whether to increase the reinforcement method of screws according to their own usage scenarios, and reinforce several screws in the whole set.
Download APP
1: Search "Smart Life" from App store or Google play.
IR Music remote controller manual
Product introduction: The 19 keys IR remote control could realize various dreamcolor modes include running water and music modes etc.
Parameters: Power supply: 3V button cell Control distance: 5-8 meters in open area
Instructions of remote control: Please remove the PVC insulation sheet from the end of the remote control before using. Please set the APP internet connection as priority when the light is blinking.
Features
ON/OFF Music mode pause/beat
Speed/sensitivity Dynamic mode switching
Music mode Automatic mode
Brightness +/-
Action
Short Press Short Press Short Press Short Press Short Press Short Press
Short Press
Remote control buttons
Static color switching W R G B
Short Press Short Press
2: Scan the QR code from the label or user manual.
The APP is compatible with Android 5.0 and IOS 10.0 and higher version.
Android 5.0
iOS10.0
Log in / Register account number
Open the Smart APP, sign up for a new account or log in with an existing account.
APP connection
1. Preparation: Turn on the LED and enter the home of APP while ensure the WIFI signal is good and stable.
2. The LED will flashing when turn on the power supply. Add all devices on the APP and enter adding lighting device interface, match LED .
My home
3. If the LED is not flashing when turn on the power supply, long press the Reset button for more than 5 seconds. While LED flashing, enter the APP adding lighting device interface,match LED.
Symphony APP function scheduled scenarios : scenery, life, festivals, mood
Dozens of preset static or dynamic scenes in four scene modes to meet the needs of different situations and occasions
DIY Scene Mode
Customize the scene with a combination of motion and color.
!"#$%& '(")* % !+! ,#-
. "
% "%" /,-
."%" " / +"%"
. ""' 0. +"
% 1" .").".") %"
"2"."3
' 4(53
)%
.!
%" 6+ /"7"#$%& '
"+"") " +"
% "%" " '3
+"/ ""%"3 ."+./% " !" /
. "
% "%" "
'8!"/"+""%" ! "" " ' 9%3
"
% "%" "" " /! )"
)."+3
%%/" "+". "" "%" )."
"%% !+
" ::&""" " +' ::9 "")!3
" "' :: 3
" %%" %"
! " " ' :: ""1" ";< %" '
!=&51"+ /3
) "!
)!
"".").> . ' 9?0>57:@@A0B:C:#B
Acrobat Distiller 19.0 (Windows)