Keurig K10 MINI Plus Brewer Owner's Manual

Important Safeguards

Safe Operation & Use

When using electrical appliances, basic safety precautions should be followed, including the following:

1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles and knobs when available.
3. This appliance must be properly installed and located in accordance with these instructions before it is used.
4. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock or injury to persons.
5. Do not place on or near a hot gas or electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock and injury do not immerse cords, plugs, or the appliance in water or any other liquid.
8. Do not overfill the Cold Water Reservoir with water.
9. Use only water in this appliance! Do not put any other liquids or foods in the Water Reservoir except as instructed in the Cleaning Instructions in this guide.
10. Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts and before cleaning the appliance.
11. For best operation, plug the appliance into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuses or tripping a circuit breaker.
12. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is damaged in any manner. Contact Keurig Customer Service to report any malfunction of or damage to the brewer.
13. Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
14. To disconnect, press the Power Button on the brewer to "OFF" status and then remove the plug from the wall outlet.
15. Close supervision is necessary when any appliance is used by or near children.
16. Do not lift the brewer Handle while brewing is in progress; scalding may occur.
17. Always keep the Cold Water Reservoir Lid closed unless you are refilling it.
18. This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
20. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
21. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
22. Do not use the appliance for other than its intended use.

Save These Instructions.

CAUTION: There are two sharp needles that puncture the K-Cup pack, one above the K-Cup Pack Holder and the other in the bottom of the K-Cup Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup Pack Assembly Housing.

CAUTION: There is extremely hot water in the K-Cup Pack Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Pack Assembly Housing during the brewing process.

CAUTION: Please always keep the brewer in its upright position to avoid potential injury and/or damage to your brewer.

SHORT CORD INSTRUCTIONS:

A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance; (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally; and (3) the extension cord must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

WARNING: Keep all plastic bags away from children.

WARNING: THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING TO USERS AND PARENTS:

1. DO NOT permit children to use brewer unless there is adult supervision. Brewer dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER USING A HOT COCOA K-CUP PACK, RUN a Hot Water Brew Cycle without a K-Cup pack to avoid the possibility of clogging the exit needle. DO NOT assume the next user will do this.

WARNING: RISK OF FIRE OR ELECTRIC SHOCK DO NOT OPEN

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

Brewer Overview

The Keurig K10 MINI Plus Brewer features the following components:

• A Water Level Guide: Located inside the Cold Water Reservoir for measuring water.
• B Handle: Used to open and close the K-Cup Pack Holder Assembly.
• C K-Cup Pack Holder Assembly: The main unit where the K-Cup pack is inserted.
• D K-Cup Pack Holder: The receptacle within the assembly that holds the K-Cup pack.
• E Funnel: Part of the assembly that directs water into the K-Cup pack.
• F K-Cup Pack Assembly Housing: The area surrounding the K-Cup Pack Holder Assembly.
• G Drip Tray Overfill Indicator: A red float that rises when the drip tray is nearly full.
• H Drip Tray Plate: The removable top part of the drip tray.
• I Drip Tray: Catches any liquid overflow.
• J Cold Water Reservoir Lid: Covers the water reservoir.
• K Cold Water Reservoir: Holds the water for brewing.
• L BREW Button: Initiates the brewing process.
• M LED Indicator: Provides status updates for brewing.
• N Power Button: Turns the brewer on and off.
• O Power Cord: Connects the brewer to the power outlet.
• P Drip Tray Base: The base structure of the drip tray assembly.

For replacement parts, please visit www.keurig.com.

Helpful Hints

1. Power Connection: Plug the Power Cord into an independent, grounded outlet. If the electric circuit is overloaded with other appliances, your brewer may not function properly.
2. Initial Cleansing Brew: Before making your first beverage, perform an initial cleansing brew without inserting a K-Cup pack.
3. One Cup at a Time: Your brewer makes one fresh beverage at a time. You will need to add fresh water each time you brew. Unlike other Keurig brewers, the K10 MINI Plus does not store water in the reservoir.
4. Water Quality: For the best-tasting gourmet coffee, tea or hot cocoa, Keurig recommends using bottled or filtered water. Distilled or reverse osmosis water is not recommended. If you notice an undesirable taste, try bottled water or water from a filtration system.
5. Customization: With over 250 K-Cup pack varieties and multiple fill levels, your brewer provides endless customization options. For a strong, intense flavor, select an Extra Bold K-Cup pack and a smaller brew size. Use the Water Level Guide to customize your brew size.
6. Brewing Iced Beverages: Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Place a tall cup filled with ice on the Drip Tray, choose your favorite K-Cup pack and follow brewing instructions. Look for the "Brew Over Ice" icon on specially crafted K-Cup packs. IMPORTANT: Do not brew into a cup made of glass. Doing so may cause the glass to crack or break.
7. Remove K-Cup pack after use: Please see brewing instructions.
8. Brewing into a Tall Mug: To brew into a tall mug, remove the Drip Tray Assembly and place the tall mug on the Drip Tray Base. Note that you lose the benefit of the Drip Tray to contain any excess liquid.
9. The Drip Tray: Any liquid overflow will be caught in the Drip Tray. Empty the Drip Tray when the red Drip Tray Overflow Indicator pops up.
10. Automatic Shut-Off: As a safety feature, your brewer will shut off automatically when it is idle for longer than 90 seconds. Press the Power Button to restart.
11. Clean Your Brewer Regularly: To keep your brewer performing at its best, clean external and internal components regularly. See page 12 for more information.
12. Descaling: Depending on water mineral content, scale may build up. Descaling helps maintain the heating element and internal parts. See page 14 for more information.
13. Storing: When storing your brewer, empty the Drip Tray and Internal Hot Water Tank. Store upright in a safe, dry, frost-free environment. See page 15 for more information.

Buttons & Indicators

• Power Button: Press to turn the brewer power on and off. (Does not illuminate)
• Add Water Indicator:
  • Flashing Blue: Fill the Cold Water Reservoir with cold water until it reaches just under the rim of the desired level (6, 8, or 10 oz. on the Water Level Guide).
• Handle Indicator:
  • Flashing Blue: The blue light flashes when the minimum water amount of 6 oz. has been poured into the Cold Water Reservoir. After adding your desired amount of water (10 oz. maximum), lower the Cold Water Reservoir Lid. The light will continue to flash until you lift the Handle.
• Brew Button:
  • Flashing Blue: Indicates you are ready to brew. Press the BREW Button.
  • Flashing Red: Indicates water is heating (approximately 2 minutes).
  • Solid Red: Indicates brewing and dispensing of beverage has begun.

Your Next Brew: When the brewing process is complete, the Add Water Indicator light will appear. At this point, you can begin making the next beverage or power off the brewer.

Automatic Shut-Off: As a safety feature, your brewer will automatically shut off when it is idle for longer than 90 seconds. Press the Power Button to restart.

Drip Tray Overfill Indicator: A red float will appear when the Drip Tray is almost full. Carefully slide the Drip Tray out and empty contents into the sink.

Set-Up & Operation

Initial Cleansing & First Brew

CAUTION: Two sharp needles are used to puncture the K-Cup packs. One is above the K-Cup Pack Holder and the other is in the bottom of the K-Cup Pack Holder. To avoid risk of injury, do not put your fingers inside the K-Cup Pack Assembly Housing.

CAUTION: During the brewing process, the water gets extremely hot. To avoid risk of injury, do not lift the Handle or open the K-Cup Pack Assembly Housing until brewing is complete.

Preparation: Remove all tape and cardboard.

Initial Cleansing Brew: Perform an initial cleansing brew before making your first beverage. Follow these instructions but do not insert a K-Cup pack.

1. Power Connection: Plug the Power Cord into an independent, grounded outlet.
2. Power On: Press the Power Button. The Add Water Indicator will flash blue. (The Power Button does not illuminate).
3. Open Reservoir Lid: Lift the Cold Water Reservoir Lid.
4. Add Water: Pour water into the Cold Water Reservoir until it reaches the desired fill level on the Water Level Guide (minimum of 6 oz., maximum of 10 oz.). Lower the lid. For accurate measuring, do not fill if the Handle is up. In the down position it prevents water from entering the lower heating compartment. Bottled or filtered water is recommended; distilled or reverse osmosis water is not.
5. Lift Handle: Lift the Handle. Water starts to drain from the Cold Water Reservoir into the brewer. If you add more than 10 oz., excess water goes into the Drip Tray.
6. Place Mug: Place a mug on the Drip Tray. If you want to use a taller mug, you can slide the Drip Tray out, but you will lose the benefit of the tray to contain any excess liquid.
7. Insert K-Cup pack: Insert the K-Cup pack into the K-Cup Pack Holder. (Do not add a K-Cup pack if you are performing the initial cleansing brew).
8. Lower Handle: Wait until all water has drained (approximately 5 seconds) into the brewer before lowering the Handle completely.
9. Start Brew: The BREW Button will flash blue. Press the BREW Button. CAUTION: Do not lift the Handle while brewing.
10. Heating: The BREW Button will flash red to indicate that the water is heating (approximately 2 minutes).
11. Dispensing: After about 2 minutes, the BREW Button will turn solid red when the beverage starts to dispense.

Enjoy your beverage! Your brewer is ready to use again or you can power it off. As a safety feature, the brewer automatically shuts off after 90 seconds.

After Brewing: Remove the used K-Cup pack after brewing. CAUTION: K-Cup pack will be hot. If completing the initial cleansing brew, discard hot water into the sink. Your brewer is ready to use again.

Cleaning & Maintenance

Cleaning External Parts

IMPORTANT: Make sure the brewer is unplugged before cleaning.

Regular cleaning of the brewer's external components is recommended:

• Brewer external housing
• Drip Tray
• Drip Tray Plate

BREWER CARE: Never immerse the brewer in water or other liquids. Clean the external housing and other external components with a damp, non-abrasive, lint-free cloth.

DRIP TRAY AND DRIP TRAY PLATE: When the red Drip Tray Overfill Indicator appears, the Drip Tray is almost full. Carefully remove by sliding the tray toward you. Empty contents into the sink. Inspect the Drip Tray periodically and clean with a damp, non-abrasive, lint-free cloth. Do not put the Drip Tray or the Drip Tray Plate in the dishwasher.

Cleaning the K-Cup Pack Holder Assembly

IMPORTANT: Make sure the brewer is unplugged before cleaning.

K-Cup Pack Holder Assembly parts include:

• Funnel
• K-Cup Pack Holder with Exit Needle

The K-Cup Pack Holder Assembly parts can be placed on the top shelf of the dishwasher. Use a low temperature cycle when cleaning.

1. Remove Assembly: Lift the Handle to open. Grasp the top of the K-Cup Pack Holder with one hand. With the other hand, push up on the bottom of the K-Cup Pack Holder Assembly until it releases.
2. Separate Funnel: Separate the Funnel from the K-Cup Pack Holder by pulling it until it snaps free.
3. Clean Exit Needle: Clean the Exit Needle on the bottom of the K-Cup Pack Holder. Insert a paper clip or similar tool from below if the needle becomes clogged by coffee grinds.
4. Replace Funnel: Snap the Funnel back into the K-Cup Pack Holder.
5. Replace Assembly: Align the K-Cup Pack Holder with the opening using the two front ribs as a guide and snap into place from the top.

Avoid sharp needles in K-Cup Pack Assembly Housing. Do not put your fingers inside the K-Cup Pack Assembly Housing.

Cleaning the Cold Water Reservoir

It is normal over time for discoloration, spotting, or staining to appear in the Cold Water Reservoir. Results vary depending on water mineral content but do not affect operation. Clean the reservoir regularly to minimize build-up.

To access the Cold Water Reservoir, lift the lid. Remove the Water Level Guide (this is not dishwasher safe) and clean inside the reservoir with a damp, non-abrasive lint-free cloth as necessary. Replace the Water Level Guide and lower the lid when finished.

Emptying the Internal Hot Water Tank

Ensure the brewer is powered off but plugged in.

• Lower the Cold Water Reservoir Lid.
• Place a mug on the Drip Tray.
• Press and hold down the BREW Button and continue to hold until all the water is dispensed into the mug. There will be a 3 to 5 second delay before water begins to dispense.

Descaling Your Brewer

Depending on water mineral content, calcium deposits or scale may build up. Descaling helps maintain the heating element and other internal parts. Descale every 3-6 months, or more often if calcium deposits build up faster.

Descaling Procedure:

You will need a large ceramic mug, fresh water, descale solution, and access to a sink. Do not use a paper cup.

STEP 1: FIRST DESCALING SOLUTION RINSE

• Turn on your brewer.
• Pour one third (4.6 oz.) of the Keurig™ Descaling Solution into the Cold Water Reservoir, then add fresh water to the 10 oz. fill level.
• Place a large ceramic mug on the Drip Tray Plate.
• Lift the Handle but do not add a K-Cup pack.
• After 5 seconds, lower the Handle and press the BREW button.
• Once solution is dispensed, discard hot contents into the sink.

STEP 2: SECOND DESCALING SOLUTION RINSE

• Repeat the process from Step 1 up until you press the BREW button.
• When the BREW button turns solid red, power off the brewer as it starts to dispense.
• Let the brewer stand for at least 30 minutes.
• Power on the brewer, lift and lower the Handle, then press the BREW button.
• Discard the hot contents into the sink.

STEP 3: FRESH WATER RINSE

• Repeat Step 1 (3 times) using 10 oz. of fresh water each time.
• You may need to perform additional Fresh Water Rinse cycles if you notice any residual taste.

NOTE: The cleaning action of Keurig™ Descaling Solution may result in foam dispensed from the brewer, which is natural. For a heavily scaled brewer, it may not fill properly after adding descaler. If this occurs, you may see little or no output followed by the sound of air blowing. If this happens: Turn off and unplug the brewer. Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse cycle. The brewer should function normally. If the problem persists, allow the brewer to sit unplugged for at least 30 minutes before continuing with the rinse. Visit www.keurig.com/descaling for more information.

Storage

Empty the Internal Hot Water Tank and Cold Water Reservoir before storing. See page 14. Store your brewer in a safe, frost-free environment in an upright position. Storing the brewer in cold temperatures may cause residual condensation to freeze inside and cause damage.

Before using your brewer after storage, wipe the Cold Water Reservoir with a damp, non-abrasive lint-free cloth and run three (3) cleaning brews (without K-Cup packs). See page 8 for initial cleansing brew process. Let the brewer rest at room temperature for at least 2 hours before powering on.

Storing the Power Cord

Behind the brewer is a convenient compartment to hold the Power Cord during transport or storage.

Troubleshooting

Should other issues arise with your brewer, please call Keurig Customer Service at 1.866.901.BREW (2739).

Warranty

Limited One Year Warranty

Keurig, Incorporated warrants that your brewer will be free of defects in materials or workmanship under normal home use for one year from the date of purchase. It is recommended that you fill out and return the warranty card enclosed with your brewer so that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase. If a replacement brewer is necessary to service this warranty, the replacement brewer may be new or reconditioned. If a replacement brewer is sent, a new limited one year warranty will be applied to the replacement brewer.

This warranty only applies to brewers operated in the United States and Canada. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and, in the case of Canada, from province to province.

Only the use of Keurig Brewed K-Cup brand packs and accessories will guarantee the proper functioning and lifetime of your Keurig brewer. Any damage to or malfunction of your brewer resulting from the use of non Keurig Brewed K-Cup brand packs and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to be caused by such use.

What is not covered by the limited warranty?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the state or province of purchase.

Other limitations:

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR K10 MINI PLUS BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you depending on the state or the province of purchase.

How do you obtain warranty service?

Keurig brewers are high-quality appliances and, with proper care, are intended to provide years of satisfying performance. However, should the need arise for warranty servicing, simply call Keurig Customer Service at our toll free phone number 1.866.901.BREW (2739). Please do not return your brewer for servicing without first speaking to Keurig Customer Service to obtain an Authorization to Return number (ATR). Keurig brewers returned without an ATR number will be returned to the sender without servicing.

Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)