PureLink HUE-100 Over HDBaseT 3.0 100 Meter Extension System User Manual

User Manual for PureLink models including: HUE-100 Over HDBaseT 3.0 100 Meter Extension System, HUE-100, Over HDBaseT 3.0 100 Meter Extension System, Meter Extension System, Extension System

Sebastian Frey

4K HDMI and USB-C Over HDBaseT 3.0 100 Meter Extension System with Bi-Directional PoC - PureLink AV

Purelink HUE-100 User Manual V1.1 - PureLink AV

File Info : application/pdf, 13 Pages, 765.83KB

Purelink HUE-100 User Manual V1.1

Purelink HUE-100 User Manual V1.1
HUE-100
4K HDMI and USB-C Over HDBaseT 3.0 100 Meter Extension System with Bi-Direconal PoC
USER MANUAL
PureLinkTM 220-10 State Route 208 Fair Lawn, NJ 07410 USA
Tel: +1.201.488.3232 Fax: +1.201.621.6118 E-mail: sales@purelinkav.com For order support, please contact your local dealer. For technical support, please contact us at support@purelinkav.com.
1

Purelink HUE-100 User Manual V1.1
Contents
Introducon .................................................................................................................................................. 3 Features ........................................................................................................................................................ 3 What's in the Box .......................................................................................................................................... 4 Specificaons ................................................................................................................................................ 4 Operaon Controls and Funcons ................................................................................................................ 5
Transmiter Panel ...................................................................................................................................... 5 Receiver Panel ........................................................................................................................................... 7 IR Cable Pin Assignment ................................................................................................................................ 8 API Commands .............................................................................................................................................. 8 Applicaon Example.................................................................................................................................... 11 Warranty...................................................................................................................................................... 12
2

Purelink HUE-100 User Manual V1.1
Introducon
The HUE-100 HDMI and USB-C HDBaseT 3.0 extension system offers full HDMI 2.0b, HDR/HDR10/HDR10+ (High Dynamic Range) 4K@60Hz 4:4:4 up to 100 meters on CAT6a/7 cable. The HUE-100 can also transport 1080P60 8 bit up to 150 meters over CAT6a/7 cable. Manual or automac selecon of HDMI and USB-C inputs is available on front panel controls and API. User defined EDID and extracon of display EDID are easy operaons using the HUE-100 simple API.
The HUE-100 provides Dolby Vision, HLG, mul-channel audio, CEC pass-through, bi-direconal RS-232 and IR control, and PoC all with zero loss and zero noise. The HUE-100 also supports Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio plus LCPM. Addionally, the low profile "slim box" enclosure design makes the HUE-100 ideal for limited space installaon environments, such as behind flat panel displays and video walls.
Features
HDMI and USB-C Inputs Manual or Automac Input Selecon API Control of:
o Manual / Auto Input Selecon EDID Management De-embedded Audio Mute / Unmute Downscaling Resoluons up to 4K/60Hz (4:4:4) HDMI 2.0b HDR /HDR10/HDR10+ HDCP 2.3 USB 2.0/1.1 Extends 4K/60Hz up to 328 . (100m) and 1080p up to 492 . (150m) HDBaseT 3.0 Uncompressed Extension High Bandwidth Support Up to 18 Gbps USB-C Port Charging up to 60W RS-232 Extension Bi-direconal PoC Power Either End from the Other Bi-direconal IR Extension
3

Purelink HUE-100 User Manual V1.1
What's in the Box
1 × 18Gbps HDMI/USB-C over HDBaseT 3.0 Extender (Transmiter) 1 × 18Gbps HDMI/USB-C over HDBaseT 3.0 Extender (Receiver) 1 × IR Blaster Cable (1.5 meters) 1 × IR Wideband Receiver Cable (1.5 meters) 2 × 3pin-3.81mm Phoenix Connector (male) 1 × 24V/3.75A Desktop Power Supply

Specificaons

Technical HDMI Compliance HDMI 2.0b

HDCP Compliance USB Compliance Video Bandwidth Video Resolution Color Space Color Depth IR Level IR Frequency HDR
Audio Formats
Transmission Distance ESD Protection Connection
Transmitter
Receiver
Mechanical Housing Color Dimensions

HDCP 2.3 USB 2.0 18Gbps Up to 4K@60Hz 4:4:4 RGB, YCbCr 4:4:4, YCbCr 4:2:2, YCbCr 4:2:0 8/10/12bit 12Vp-p Wideband 20K-60KHz HDR, HDR10, HDR10+, Dolby Vision, HLG HDMI/USB-C/HDBT: LPCM 2/5.1/7.1CH, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD 3.5mm Analog Audio: LPCM 2CH HDBT Standard Mode (4K60/4K30/1080P): 328ft/100m (CAT6A/7) HDBT Long Reach Mode (1080P 8bit): 492ft/150m (CAT6A/7)
Human body model -- ±8kV (Air-gap discharge) & ±4kV (Contact discharge)
Input: 1 x HDMI IN [Type A, 19-pin female] 1 x USB-C IN [USB Type C, 24-pin female]
Output: 1 x HDBaseT OUT [RJ45, 8-pin female] 1 x L/R OUT [3.5mm Stereo Mini-jack]
Control: 1 x IR IN [3.5mm Stereo Mini jack] 1 x IR OUT [3.5mm Stereo Mini-jack] 1 x RS-232 [3pin-3.81mm phoenix connector] 1 x SERVICE [Micro USB, 5-pin female] 1 x USB HOST [USB Type B, 4-pin female] 3 x USB Devices [USB Type A, 4-pin female]
Input: 1 x HDBaseT IN [RJ45, 8-pin female] Output: 1 x HDMI OUT [Type A, 19-pin female]
1 x L/R OUT [3.5mm Stereo Mini-jack] Control: 1 x IR IN [3.5mm Stereo Mini-jack]
1 x IR OUT [3.5mm Stereo Mini-jack] 1 x RS-232 [3pin-3.81mm phoenix connector] 1 x SERVICE [Micro USB, 5-pin female] 2x USB Devices [USB Type A, 4-pin female]
Metal Enclosure Black Transmitter: 170mm [W] x 102mm [D] x 22mm [H]Receiver: 144mm [W] x 78mm [D] x 23mm [H]

Weight Power Supply

Transmitter: 484g, Receiver: 318g Input: AC 100 - 240V 50/60Hz

Purelink HUE-100 User Manual V1.1

Output: DC 24V/3.75A (US/EU standard, CE/FCC/UL certified)

Power Consumption (Max) Operating Temperature Storage Temperature
Relative Humidity
Resolution / Cable Length
HDMI IN / OUT

94.32W (Power supply from TX, 60W USB-C charging, POC to RX)10.8W (Power supply from TX or RX, without USB-C charging)

32 - 104°F / 0 - 40°C
-4 - 140°F / -20 - 60°C 20 - 90% RH (no condensation)
4K60 Feet / Meters 26ft / 8M

4K24 Feet / Meters
39ft / 12M

1080P60 Feet / Meters
50ft / 15M

Operaon Controls and Funcons

Transmiter Panel

No.

Name

1 Power LED

2 LINK LED (Green)

USB-C LED 3 (Green)

HDMI LED 4 (Green)

SELECT button

6 MODE switch

EDID DIP 7 switch

Function Description
Red LED indicates that the transmitter is powered on. Light on: Transmitter and receiver are in good connection status. Light flashing: Transmitter and receiver are in poor connection status. Light off: Transmitter and receiver are not connected.
When the USB-C IN port is selected as the video signal input channel, the USB-C LED will be on. When the HDMI IN port is selected as the video signal input channel, the HDMI LED will be on.
Press this button to switch HDMI/USB-C signal input.
Used to switch HDBT mode. Switch to "STD": The HDBT Standard Mode (as factory default) is enabled, it can extend 4K60/4K30/1080P signal between the transmitter and the receiver up to 100m via a single CAT6A/7 cable. Switch to "LRM": The HDBT Long Reach Mode is enabled, it can extend 1080P 8bit signal between the transmitter and the receiver up to 150m via a single CAT6A/7 cable. Used for EDID setting: 00 - Copy display's EDID (as factory default) 01- 4K30 4:4:4 10- 1080p60 4:4:4 11- 1200p60 4:4:4

Purelink HUE-100 User Manual V1.1

USB Device Ports 8

Three USB extension ports, connected to mouse, keyboard, USB Flash Drive or other USB devices, with a maximum power supply of 500mA.

9 SERVICE HDBaseTOUT
10

Firmware update and API command control port.
HDBaseT output port, connected to the HDBaseT IN port ofreceiver with a CAT6A/7 cable. It is used for various signals pass-through.

Data Signal Indicator (Yellow)

Light on: There is video signal transmission with HDCP encryption. Light flashing: There is video signal transmission without HDCP encryption. Light off: There is no video signal transmission.

Link Signal 12 Indicator (Green)

Light on: Transmitter and receiver are in good connection status. Light flashing: Transmitter and receiver are in poor connection status. Light off: Transmitter and receiver are not connected.

13 HDMI IN
14 USB-C port
15 USB HOST 16 L/R OUT 17 IR IN 18 IR OUT 19 RS-232 20 DC 24V 21 POC switch

HDMI signal input port, connected to HDMI source device. USB Type C port with following three functions: (1) USB-C video signal input port, connected to source device. (2) USB-C host port. When the USB-C port is selected as the video signal
input channel, the USB-C port can be used as a USB 2.0 signal transmission port simultaneously. (3) USB-C charging port. Only when TX is connected to the 24V/ 3.75A power supply, the USB-C port can provide 60W charging power for external USBC devices. When TX is not connected to the power supply and RX is connected to the power supply, the USB-C port cannot provide charging function. USB host port, connected to PC. It follows the HDMI IN port. When the HDMI IN port is selected as the input channel, the USB 2.0 signal can only be output through the USB HOST port.
Analog audio output port, used for audio de-embedding output.
IR signal input port, connected with the IR Receiver cable.
IR signal output port, connected with the IR Blaster cable. RS-232 serial port, used for RS-232 command pass-through and API command control.
DC 24V/3.75A power supply input port. Note that the extender supports POC function, it means that either transmitter or receiver is powered on by 24V/3.75A power adapter, the other one doesn't need a power supply.
Use the switch to turn on/off the POC function.

Note: In the HDBT Long Reach Mode, due to bandwidth limitations, USB cannot transmit USB 2.0 devices, but only can transmit USB HID devices (such as mice and keyboards). When using the USB pass-through function, the serial baud rate may also be limited.

Receiver Panel

Purelink HUE-100 User Manual V1.1

No. Name

Function Description

1 Power LED Red LED indicates that the receiver is powered on.

Light on: Transmitter and receiver are in good connection status. 2 LINK LED Light flashing: Transmitter and receiver are in poor connection status.

(Green) Light off: Transmitter and receiver are not connected.

3 IR IN

IR signal input port, connected with the IR Receiver cable.

4 IR OUT IR signal output port, connected with the IR Blaster cable. 5 SERVICE Firmware update and API command control port.

6 HDBase TIN
Data 7 Signal
Indicator

HDBaseTinputport,connectedtotheHDBaseTOUTportoftransmitterwithaCAT6A/7 cable.It is used for various signals pass-through. Light on: There is video signal transmission with HDCP encryption. Light flashing: There is video signal transmission without HDCP encryption. Light off: There is no video signal transmission.

(Yellow)
Link 8 Signal
Indicator

Light on: Transmitter and receiver are in good connection status. Light flashing: Transmitter and receiver are in poor connection status. Light off: Transmitter and receiver are not connected.

(Green)

9 HDMI OUT HDMI signal output port, connected to HDMI display device, such as a TV or monitor.

USB 10 Device
ports 11 L/R OUT
12 RS-232

Two USB extension ports, connected to mouse, keyboard, USB Flash Drive or other USB devices.
Analog audio output port, used for audio de-embedding output. RS-232 serial port, used for RS-232 command pass-through and API command control.

13 DC 24V

DC 24V power supply input port. Note that the extender supports POC function, it means that either transmitter or receiver is powered on by 24V power adapter, the other one doesn't need a power supply.

14 POC switch Use the switch to turn on/off the POC function.

Purelink HUE-100 User Manual V1.1
IR Cable Pin Assignment
The pin assignment of the IR Receiver cable and IR Blaster cable is as below:

Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters.

API Commands
The product also supports API commands control. Connect the RS-232 port of the product to a PC or control system with a 3-pin phoenix connector cable or connect the SERVICE port of the product to a PC with a Micro USB cable. Then, open a serial command tool on PC to send ASCII commands to control the product. The ASCII commands list about the product is shown below.

ASCII Commands RS-232 Communication Protocol Baud rate: 115200; Data bit: 8; Stop bit: 1; Parity bit: none. The end mark of command is "<CR><LF>".

Command Code Function Description

Example

help

Get the list of all

commands

help

Feedback ====================== Help Info FW Version:TX 1.00.02 RX 1.00.02 00. help 01. r fw version 02. s reboot 03. s reset 04. r status 05. s tx input x 06. r tx input 07. s tx autoswitch x 08. r tx autoswitch 09. s tx autoswitch mode x 10. r tx autoswitch mode 11. s rx downscale x 12. r rx downscale 13. s tx audio mute x 14. r tx audio mute 15. s rx audio mute x 16. r rx audio mute 17. s edid x to y 18. r edid x 19. r edid data x 20. s user edid x <y> 21. r user edid x ======================

Default

Purelink HUE-100 User Manual V1.1

r fw version s reboot s reset
r status
s tx input x r tx input s tx autoswitchx r tx autoswitch s tx autoswitch mode x r tx autoswitch mode
s rx downscalex
r rx downscale s tx audio mutex r tx audio mute s rx audio mutex r rx audio mute

Get the firmware version r fw version

Reboot the device

s reboot

Reset to factory defaults s reset

TX 1.0.0 RX 1.0.0 Reboot... System Initializing... Initialization Finished!TX 1.0.0 RX 1.0.0
Sure to RESET to default settings? Type "Yes" after next prompt to confirm...

Get system status

r status

Input: USB-C Video: 1920x1080p60 Audio:48K PCM 2CHHDCP: 1.4 USB Host: ConnectedHDBT Link: ON HDBT Signal: ON EDID: DIP_00 (Copy display's EDID)

Set TX input video x = USBC, HDMI, AVMUTE, OFF
Get TX input port Set TX auto-switching on/off x = ON, OFF Get TX autoswitching status Set TX auto-switching mode x = 0: 5V detection 1: signal detection Get TX autoswitching mode status Set RX downscaling mode, x= AUTO: automatically according to display's capability ON: force 4K to 1080pOFF: bypass video
Get RX downscaling mode Set TX de-embedding audio mute on/off x = ON, OFF Get TX de-embedding audio mute status
Set RX de-embedding audio mute on/off x = ON, OFF Get RX de-embedding audio mute status

s tx input USBC

Set tx input from USBC

r tx input

USBC

s tx autoswitchON Set tx autoswitch ON

r tx autoswitch ON

s tx autoswitch mode 1
r tx autoswitch mode

Set tx autoswitch mode 1:signal detection
TMDS

s rx downscale AUTO

Set rx downscale AUTO

r rx downscale AUTO s tx audio muteON Set tx audio mute ON r tx audio mute OFF s rx audio muteON Set rx audio mute ON r rx audio mute OFF

USBC ON 1: signal detection
AUTO
OFF OFF

Purelink HUE-100 User Manual V1.1

Set input ports EDID

x = USBC, HDMI, ALL

y =

00 - EDID dip switch

(default)

01 - 1920x1080@60 8bit

Stereo

02 - WUXGA 1920x1200

03 - 1920x1080@60 8bit

High Definition Audio

04 - 3840x2160@60Hz

s edid x to y

4:2:0 Deep Color Stereo

Audio

s edid USBC to00 Set edid USBC to 00 - EDIDdipswitch

05 - 3840x2160@60Hz

(default)

Deep Color Stereo

Audio06 -

3840x2160@30Hz

8bit Stereo Audio

07 - 3840x2160@60Hz

Deep

Color High Definition

Audio

3840x2160@60Hz Deep

Color HDR LPCM 6CH

09 - copy EDID from RX

HDMI output

10 - User Defined 1

11 - User Defined 2

r edid x

Get input ports EDID x = USBC, HDMI

r edid USBC 00 - EDID dipswitch (default)

r edid data x

Get input ports EDID datax = USBC, HDMI

r edid data USBC

USBC EDID <00 FF FF FF....>

Set user defined EDID

s user edid x <y>

x = 1 (User Defined 1) x = 2 (User Defined 2) y = 00 FF FF FF .....

s user edid 1 <00 FF FF FF....>

User edid 1 is loaded

(y is 256 bytes EDID data)

r user edid x

Get user defined EDID x = 1 (User Defined 1) x = 2 (User Defined 2)

User edid 1 r user edid 1 <00 FF FF FF....>

Set Micro USB (UART) to

s hdbt update HDBT UART for FW

s hdbt update Hdbt update

update

Note: The API command "s hdbt update" is for internal use only .

Purelink HUE-100 User Manual V1.1
Applicaon Example
11

Purelink HUE-100 User Manual V1.1
Warranty
PureLink Three (3) Year Limited Warranty for PureStreamTM Branded Products Only
Dtrovision, LLC. (hereinafter "PureLink") warrants its HDTools and PureStreamTM branded products (hereinafter "Product") purchased directly from PureLink or Dealer shall be free from defects in workmanship and materials, under normal use and service, for a period of three (3) years on parts and three (3) years on labor. Any repaired or replaced equipment related to Product shall be covered only under the remaining portion of the warranty. This warranty has no relationship to and exists independently of any warranty offered by Dealer. This warranty is a limited warranty and gives you specific legal rights. You may also have other rights which vary from state to state.
TERMS & CONDITIONS PureLink shall repair or replace the Product if it develops a material fault during the period of warranty, on condition that i) the Product has only been subject to normal use in a domestic or commercial environment in a manner consistent with its specification and functionality, ii) the Product has been cared for reasonably and only subjected to reasonable wear and tear, iii) the defect has not been caused by willful or negligent abuse or neglect, or any accident or improper installation procedure, iv) the serial number of the Product has not been altered or removed.
This warranty only applies to the original purchaser, and shall be the exclusive remedy to the original purchaser. PureLink shall not be liable for any damages whatsoever caused by Product or the failure of Product to perform, including incidental or consequential damages. PureLink shall not be liable for any claim made by a third party or made by the purchaser for a third party.
Except as expressly set forth in this warranty, PureLink makes no other warranties, expressed or implied, including any implied warranties of merchantability and fitness for a particular purpose. PureLink expressly disclaims all warranties not satisfied in this limited warranty. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
WARRANTY RETURNS/REPAIRS/EXCHANGES
No merchandise may be returned without prior authorization from PureLink, and a Return Materials Authorization (RMA) number. Failure to comply with these conditions will result in rejection of the returned merchandise.
Any warranty service on Products must be arranged through Dealer. Authorized returns must be shipped freight prepaid and fully insured to PureLink, Ramsey, NJ USA, with the RMA number clearly marked on the outside of all shipping boxes and containers. PureLink reserves the right at its sole discretion to refuse any shipments arriving freight collect or without an RMA number. Any authorized returned merchandise must be accompanied by a note describing the reason for return, along with contact information including name, phone number, return mailing and shipping addresses, e-mail address, and RMA number.
On any products returned and accepted with an RMA number, return freight charges following repair of items under warranty shall be paid by PureLink, shipping by the standard ground carrier of its choice.
ADVANCE WARRANTY REPLACEMENTS
PureLink's advance replacement service offers a Replacement Unit upon request - free of charge for eligible products purchased less than one (1) year of the warranty claim. Products purchased more than one (1) year prior to the warranty claim do not qualify for advance replacement services.
Advance replacement requests must be validated by a member of PureLink's Technical Support Team. Replacement units may be new or refurbished and is subject to availability. PureLink is responsible for shipping the Replacement Unit to your designated location by standard ground service. All other shipping methods will be responsibility of the Dealer.
12

Purelink HUE-100 User Manual V1.1
Original Unit Return the Original Unit must be returned within thirty (30) calendar days of the return authorization date. Failure to return the Original Unit within this period will be subject to a minimum 15% re-stocking fee. Dealer is solely responsible for the shipping of the Original Unit to PureLink. TO MAKE A WARRANTY CLAIM To make a warranty claim, promptly notify PureLink within the warranty periods described above by calling PureLink's Technical Support Department at 1-201-488-3232. PureLink, in its sole discretion, will determine what action, if any, is required under this warranty. Most problems can be corrected over the phone through close cooperation between Customer and a PureLink technician. To better enable PureLink to address a warranty claim, please have the Product's serial and model numbers. If PureLink, in its sole discretion, determines that an on-site visit or other remedial action is necessary, PureLink may send a representative to Customer's site. CUSTOMER SERVICE Technical support inquiries can be submitted electronically through the PureLink website at www.purelinkav.com. For immediate assistance please contact PureLink's Customer Care Team at +1 (201) 488-3232
13

References

Adobe PDF Library 23.8.53