Installation Guide for KRAUSE models including: Veloci Street Glide Pullback Plate, Glide Pullback Plate, Pullback Plate
Kraus Product Support | How-Toâs and Assembly Guides
Kraus Veloci Riser Pullback Plate For Harley Street Glide 2023-2024 - Cycle Gear
Veloci Street Glide Pullback Plate X ++ Install Guide VELOCI STREET GLIDE PULLBACK PLATE INSTALL GUIDE DISCLAIMER: Kraus Motor Co. recommends that you defer to a certified mechanic or technician on any installation when possible. Refer to your OEM service manual for procedure, step by step run through, required tools and specifications to make sure all pieces and parts are properly installed. Kraus Motor Co. is not responsible for improper installation of any OEM or Kraus component/kit. A er completing installation, go for a slow, careful test ride. A erword's, double check all pieces, parts and systems. Improper installation may result in severe injury or death. Before Installation: - Please note you will lose access to the front phone drawer. You may use a USB Type-C extension cable to relocate the connection to gain acces to OEM usb features. -We strongly recommend ordering OEM PN: 37200592 (Replacement upper clutch cable) Torque specs: 1) - 55 FT LBS 2)- 55 FT LBS To begin installation: (1) Completely remove front fairing. (2) Remove clutch and brake master cylinder from bars. (11) The assembly can now be installed onto the top tree using the provided solid bushings. (12) Install bars onto midsection (if not already installed ) 1 (3) Remove the handlebars. (13) Install brake master and clutch perch onto bars. NOTE: Ensure all connectors are disconnected. NOTE: Replacement upper clutch cable (4) Push out OEM Bushings from tree, they will not be reused. should be installed at this time. (5) Remove switches and wires from bars. (14) Route cables and wiring. The channel in the center of the pullback plate is designed for routing wires. (6) Run wiring into new bars. (7) Assemble Risers onto the pullback plate. See your riser installation schematic for riser torque specs. (8) Trim the lower nacelle using the cu ing template located on the second page of this document. NOTE: Brake line should be removed from 2 plastic holder on neck for more slack. NOTE: Threaded holes in the bo om of the plate offer a position for P-clamps to be installed for neater installation of cables. Threaded holes are 10-24 size. (9) Install lock cover trim piece without screws into lower nacelle, place lower nacelle loose above lock. (15) Inner fairing can be reinstalled. Followed by reassembling the rest of the components. NOTE: To remove the nacelle without removing the risers in the future, cut off the tabs from the lock cover and a ach it using 3M tape. Alternatively, you can discard the cover for easier removal and reinstallation of the nacelle in the future. NOTE: Be mindful of the white tabs that will need to click into the inner fairing. These can be reached through the holes in the side of the fairing where the previous bars were located. The inner fairing can slide over the white clips and the clips can be depressed to click into the main inner fairing. This may take some finesse. (10) Bolt your risers to the pullback plate. ©2024 - Kraus Motor Company support@krausmotorco.com Veloci Street Glide Pullback Plate TECH TIP: Apply tape along the outer folds to ensure a snug fit. X ++ Street Glide Nacelle Cut Template FOLD Cut the nacelle along this interior red line 6 in. FOLD Do not continue to cut straight along this black line. Continue along the curved back side (See page 3) Comfirm sizing and placment is correct by aligning these holes Install Guide FOLD: CUT: ©2024 - Kraus Motor Company Center Line Confrim printed paper is correct by confirming this scale. If it is not correct, please contact support@krausmotorco.com NOTE: Be sure to print in "Actual Scale" support@krausmotorco.com Veloci Street Glide Pullback Plate X ++ BEFORE Cut the nacelle along this red line Do not continue straight along this line -Instead, make a level cut along the curve of this flat surface FOLD FOLD AFTER Install Guide ©2024 - Kraus Motor Company support@krausmotorco.comAdobe PDF library 17.00 Adobe Illustrator(R) 24.0