PRODUKT MANUAL

Caution

Avoid Overloading

Do not use the converter beyond its maximum power. When connected to any appliance with a built-in motor compressor, the starting power is generally several times the appliance's listed power rating. Ensure the total starting power capacity of all connected appliances does not exceed the listed maximum output power of the converter. For color TVs, calculate capacity twice the listed value. Ensure the converter's output voltage and frequency match the connected appliances. Verify the electrical source voltage matches the converter's input voltage.

Environment

Always place the converter in an environment that is:

• Well ventilated.
• Not exposed to direct sunlight or heat sources.
• Out of reach of children.
• Away from water, moisture, oil, or grease.
• Away from any flammable substance.

If the power cord is damaged, it must be replaced by authorized dealers or similarly qualified persons to avoid a hazard.

Circuit Breaker Operation

When appliances are connected to the converter and power is “ON”, if the circuit breaker opens, it indicates the converter is overloaded with too many appliances. Connecting too many appliances draws excessive power, causing the circuit breaker to trip. If this occurs, switch the converter “OFF”, unplug it from the wall outlet, and reduce the load by unplugging appliances. Unplug the converter from the wall. Press the circuit breaker button. Wait a few minutes, then switch the power to the “ON” position. Then switch “ON” appliances one by one, ensuring their combined rated power does not exceed the converter's rating power.

Remarks

This model is single phase. Waveform is sinuous and without distortion.

Instructions for the Converter

Familiarize yourself with the various features and facilities by studying the diagrams below to obtain maximum benefit from the converter.

Front of the Converter

Diagram showing the front panel of the Voltage Converter VP. Features include a power switch, power source LED indicator, and output socket. The unit is labeled 'Step-up & Step-down Voltage Converter'.

Rear of the Converter

Diagram showing the rear panel of the Voltage Converter VP. Features include a circuit breaker reset button and input connection points. The unit displays CE certification and a voltage selection warning.

Connection and Operation

Step 1: Connect Electrical Appliances

Check the wattage requirement of your equipment from the nameplate and specifications to determine the correct wattage and which converter to use. If your appliances' voltage rating is 110V, your main voltage must be 220V. If your appliances' voltage rating is 220V, your main voltage rating must be 110V.

Step 2: Connect to Electrical Mains

Plug the AC mains cord into a wall socket as shown in the diagram and switch “ON”. Select the correct input voltage according to your area mains. Ensure all appliances are turned “OFF” before making connections. Make connections as shown in the diagrams, ensuring the total starting power needed does not exceed the rated maximum output power of the converter.

Step 3: Switch On the Converter

Switch the power to “ON”. Press the power “ON/OFF” switch to the “ON” position, and the LED will illuminate. Switch “ON” the appliances one by one.

Illustrations demonstrating the connection of appliances to the Voltage Converter VP. One diagram shows a television connected, and another shows a refrigerator. Both illustrate the converter plugged into a wall socket and the appliance plugged into the converter's output, with emphasis on correct input voltage selection (230V/110V).

Technical Data and Warranty

Technical Data

Models

A series of product images showcasing the VOLT POLSKA Voltage Converter VP models: VP 500 VA, VP 1000 VA, VP 2000 VA, VP 3000 VA, and VP 5000 VA.

Warranty Information

Warranty Card

DATE OF PURCHASE:

SHIPPING ADDRESS:

SIGNATURE / STAMP:

DAMAGE DESCRIPTION:

SERVICE COMMENTS:

FILL IN IF NEEDED. (*) Cross incorrect.

I agree to pay the cost of repair due to: expiration of the warranty period / warranty void.

Before proceeding with the repair, service will inform by phone about the exact costs. Please attach a copy of the purchase document (receipt or invoice) to the complaint. The full regulations of service repairs can be found on our website.

CE [WEEE symbol]