Manuals+

Horizon Fitness Andes 5 & 7i Elliptical Trainer Bedienungsanleitung

This manual provides comprehensive instructions for the assembly, operation, and maintenance of the Horizon Fitness Andes 5 and Andes 7i elliptical trainers.

Important Safety Information

WARNING: To reduce the risk of burns, fire, electric shock, or injury:

Grounding Instructions

In case of malfunction or failure of the elliptical trainer, grounding provides the path of least resistance for electric current and helps reduce the risk of electric shock. The equipment comes with a power cord that includes an grounding conductor and a grounding plug. The plug must be connected to an outlet that is properly installed and grounded in accordance with all applicable local codes and ordinances. Improper connection of the equipment-grounding conductor can result in electric shock. Consult a qualified electrician or service person if you have doubts about proper grounding. Do not modify the plug provided with the equipment. If it does not fit the outlet, have a qualified electrician install a proper outlet.

WARNING: Only connect this equipment to a properly grounded outlet. Do not use the equipment if the cord or plug is damaged, even if the equipment is otherwise functioning normally. Never use equipment that appears damaged or has become wet. Repairs and replacement parts are available from your local dealer.

WARNING: The heart rate monitoring system may be inaccurate. Overtraining can lead to serious injury or death. If your performance decreases unusually, stop training immediately!

Assembly

WARNING: Pay close attention during some assembly steps. It is very important that you follow the assembly instructions precisely to ensure all parts are tightened securely. Failure to follow the assembly instructions may result in parts of the elliptical trainer not being tightened sufficiently, coming loose, and causing noise. To avoid damage to your elliptical trainer, re-read the assembly instructions and correct any errors that may have occurred during assembly.

Before beginning assembly, enter the serial number of the elliptical trainer below. The serial number and model name can be found on the frame.

Enter Serial Number and Model Name:

Serial Number: [ ]

Model Name: ELLIPTICAL HORIZON FITNESS

Included Tools: Before Assembly

Included Parts:

Unpacking:

Unpack the equipment where it will be used. Place the elliptical trainer's packaging on a flat surface. We recommend placing a protective sheet on your floor to prevent scratches. Do not open the packaging if it is lying on its side.

NOTE: During each assembly step, ensure ALL nuts and bolts are lightly tightened before ONE is fully tightened.

NOTE: We recommend lubricating the screw threads with a little grease during assembly. Any type of grease, such as bicycle grease, is suitable.

Need Help?

If you have questions or missing parts, please contact our customer service. Contact information can be found on the back of the user manual or on the warranty card.

Assembly Step 1

  1. Remove the 4 pre-attached washers (A) and 4 screws (B) from the main frame (2).
  2. Carefully pull the console cable from the console mast (1) and then connect it to the other console cable from the main frame (2).
  3. Attach the console mast (1) to the main frame (2) using the 4 washers (A) and 4 screws (B) removed in Step A.

Screw Bag for Step 2 Includes:

Part Type Description Quantity
C RING Φ16.0ΧΦ26.2X11.5T 2
D WASHER Φ16.0ΧΦ25.0X1.5T 4
E WASHER Φ8.6ΧΦ26.0X2.0T 2
F SPRING WASHER Φ8.2ΧΦ15.4X2.0T 2
G SCREW M8X1.25PX20L 2
H COVER 2
  1. Attach the arm stride set (3) to the console mast (1) with 1 ring (C), 2 washers (D), 1 washer (E), 1 spring washer (F), and screw (G) and 1 cover (H).
  2. Repeat Step A on the other side.
  3. Attach the console mast cover (4 & 5) to the main frame (2).

Assembly Step 3

Screw Bag for Step 3 Includes:

Part Type Description Quantity
F SPRING WASHER Φ8.2ΧΦ15.4X2.0T 2
I SCREW M8X1.25PX70L-12L 2
J WASHER Φ8.2ΧΦ20.0X1.5T 2
K NUT M8X1.25P 2
  1. Attach the pedal arm (6) to the arm stride set (3) with 1 screw (I), 1 washer (J), 1 spring washer (F), and 1 nut (K).
  2. Repeat Step A on the opposite side of the elliptical trainer.

Specifications

Andes 5

ECB Magnetic Brake System
Dimensions: 1740 x 690 x 1750 mm (66" x 27" x 69")
Folded Dimensions: 1025 x 690 x 1750 mm (40" x 27" x 69")
Max User Weight: 136 kg / 300 lbs
Net Weight: 78.7 kg / 174 lbs
Gross Weight: 93.7 kg / 207 lbs

Andes 7i

Induction Brake System
Dimensions: 1740 x 690 x 1720 mm (66" x 27" x 68")
Folded Dimensions: 1025 x 690 x 1720 mm (40" x 27" x 69")
Max User Weight: 136 kg / 300 lbs
Net Weight: 82.5 kg / 182 lbs
Gross Weight: 97.5 kg / 215 lbs

ASSEMBLY COMPLETE!

Folding System

Folding:

  1. Position the pedal wheel correctly. For easier folding, position the left or right pedal wheel in the ideal folding range (see Figure 1 below).
  2. Turn the pedal arm and position the pedal wheel as shown in Figure 2 or Figure 3.
  3. Grip the handle (Figure 4).
  4. Pull upwards until the guide rail set locks into place.

Unfolding:

  1. Grip the handle, push slightly forward.
  2. Pull up on the handle to release the lock.
  3. Pull backward and then fold the equipment down.

Transport

WARNING! Our training equipment is built with high-quality, heavy components. Therefore, be careful and seek assistance for transport if necessary. Failure to heed this warning may result in injury.

Elliptical Trainer Operation

This section explains how to use your elliptical trainer and its programs. The BASIC OPERATIONS section in the TECHNICAL MANUAL includes the following instructions:

Andes 5 Console Operation

Note: The console has a thin protective layer of clear plastic. Please remove it before use.

A) LCD DISPLAYS: Time, Distance, Speed, RPM, Resistance, Heart Rate, Calories, Watts, HR Wheel, Resistance Profile, Connection to Passport.

B) ENERGY SAVER MODE: To reduce energy consumption, your equipment automatically switches to energy saver mode (after 15 minutes of standby) and can be reactivated by pressing any button.

C) ARROW KEYS: Use the up and down arrows to select a program, set up your console, or change resistance during exercise.

D) ENTER KEY: Confirms training program or user profile settings.

E) START/STOP Button: Press to start, pause, or resume exercise. Press and hold the stop button for 3 seconds to reset the console to zero.

F) DISPLAY CHANGE / BACK BUTTON: Allows you to scroll through display modes and workout summaries. Pressing this button allows you to switch between display columns and between the resistance profile (top bar) and the current workout watt profile (bottom bar). Also used for navigation back to user setup.

G) Audio Jack: Connect your phone or MP3 player to play music through the integrated speaker during your workout.

H) Resistance Direct Select Buttons: Use these buttons to select the desired training resistance directly.

I) SPEAKERS: Play music through the speakers when your media player is connected.

J) SMART DEVICE TRAY FOR PHONE AND BOOK: Holds your phone, tablet, or reading material.

K) PASSPORT: Displays when connected to Passport.

L) PASSPORT QUICK SELECT BUTTON: Used to connect to Passport. Press this button when you want to synchronize with Passport.

M) VOLUME BUTTON: Used to adjust volume up and down.

Andes 7i Console Operation

Note: The console has a thin protective layer of clear plastic. Please remove it before use.

A) LCD DISPLAYS: Time, Distance, Speed, RPM, Resistance, Heart Rate, Calories, Watts, HR Wheel, Resistance Profile, Connection to Passport.

B) ENERGY SAVER MODE: To reduce energy consumption, your equipment automatically switches to energy saver mode (after 15 minutes of standby) and can be reactivated by pressing any button.

C) ARROW KEYS: Use the up and down arrows to select a program, set up your console, or change resistance during exercise.

D) ENTER KEY: Confirms training program or user profile settings.

E) START/STOP Button: Press to start, pause, or resume exercise. Press and hold the stop button for 3 seconds to reset the console to zero.

F) CHANGE DISPLAY / BACK BUTTON: Allows you to scroll through display modes and workout summaries. Pressing this button allows you to switch between display columns and between the resistance profile (top bar) and the current workout watt profile (bottom bar). Also used for navigation back to user setup.

G) Audio Jack: Connect your phone or MP3 player to play music through the integrated speaker during your workout.

H) Resistance Direct Select Buttons: Use these buttons to select the desired training resistance directly.

I) SPEAKERS: Play music through the speakers when your media player is connected.

J) SMART DEVICE TRAY FOR PHONE AND BOOK: Holds your phone, tablet, or reading material.

K) PASSPORT: Displays when connected to Passport.

L) PASSPORT QUICK SELECT BUTTON: Used to connect to Passport. Press this button when you want to synchronize with Passport.

M) VOLUME BUTTON: Used to adjust volume up and down.

Andes 5 Program Profiles

Heart Rate Training Zones:

PASSPORT: Displays when the equipment is in Passport mode and can be synchronized with Passport.

Andes 7i Program Profiles

Heart Rate Training Zones:

WATT SCALE AND PROFILE DISPLAY: This display shows your current workout watts, e.g., a 50W point appears when you reach or select 25-50 watts. You can return to the workout profile display using the Change Display button.

Note: The scale only shows up to 400 W in the Watt programs to reflect your target watt range of 25-400 watts.

PASSPORT: Displays when the equipment is in Passport mode and can be synchronized with Passport.

Getting Started

QUICK START / QUICK START

  1. Ensure the equipment is powered on.
  2. Press the START/STOP button to begin training in manual mode.
  3. Press [up/down arrows] to adjust resistance during training.

Starting a Workout:

  1. Select Guest / User1 / User2 / User3 / User4.
  2. Enter weight.
  3. Enter age.
  4. Select a program.
  5. Select gender (required for FitTest program).
  6. Set program settings, time, difficulty level, etc.
  7. Press the START/STOP button to begin the workout.

Note: The console saves your settings for Users 1/2/3/4 for the next workout.

Canceling Selection / Resetting Console:

Press and hold the START/STOP button for 3 seconds.

Ending the Workout:

When your workout is finished, the bike will stop and beep. You can unplug the equipment, or it will automatically switch to energy saver mode after 15 minutes.

Program Information

Andes 5: 10 Programs

Manual, Intervals, Game, Weight Loss, Rolling, Reverse Train, Random, Constant Watts, THR Zone, Custom.

Andes 7i: 14 Programs

Manual, Intervals, Game, FitTest, Weight Loss, Weight Loss Plus, Rolling, Reverse Train, Constant Watts, Interval Watts, THR Zone, % THR, Strength Builder, Custom.

1) MANUAL/MANUAL:

Manually adjustable program without preset settings. Resistance can be changed at any time. Adjust your resistance manually during your workout. The user defines the time and resistance using the arrow keys and presses ENTER.

2) INTERVALS / INTERVALS:

Improves your strength, speed, and endurance by alternating between light and strong resistance to train your heart and muscles. Time-based program with 16 intensity levels to choose from. The user defines the time and resistance using the arrow keys and presses ENTER.

INTERVALS / INTERVALS (Table provided for Andes 5 & 7i with detailed level and time settings)

3) GAME/GAME:

This warm-up program simulates a car race. By pedaling fast and slow, you can control the car up and down. Avoid obstacles and try to stay on the track. Your remaining attempts are displayed on the upper LCD with 10 points per attempt. Each time you hit an obstacle, one point is deducted. You only have 11 attempts to complete the track, so be careful!

4) FIT-TEST/FITNESS TEST:

Test your current physical fitness. Keep the pedaling speed (RPM) between 60 and 80 during the test. The program automatically changes the resistance during the test according to a stored table. Try to maintain your speed until you can no longer. The console then compares your result with the stored table and shows your current fitness level.

Protocol for Men / Protocol for Women (Tables provided for level, time, and intensity in watts)

5) WEIGHT LOSS / WEIGHT LOSS:

Ideal for reducing body weight, alternating between strong and weak resistance, but always in the fat-burning zone. Time-based program with 16 intensity levels to choose from. The user defines the time and resistance using the arrow keys and presses ENTER. Drink enough water during and after training to improve weight loss.

WEIGHT LOSS (Table provided for level and time settings)

6) WEIGHT LOSS PLUS / WEIGHT LOSS PLUS (ANDES 7i ONLY):

Ideal for reducing body weight, alternating between strong and weak resistance, but always in the fat-burning zone. This is a time-based program with 15 levels, offering more choices and greater intensity than the Weight Loss program. The user defines the time and intensity using the arrow keys and presses ENTER. Drink enough water during and after training to improve weight loss.

WEIGHT LOSS PLUS (Table provided for level and time settings)

7) ROLLING / ENDURANCE:

Maintains your weight through gradual changes between weak and strong resistance, proportional to gradual changes between low and high heart rates.

8) REVERSE TRAIN / REVERSE TRAINING:

A special training program for muscle building. This program gradually increases resistance and prompts you to pedal forward (F) or backward (R) to achieve your fitness goals. Random.

REVERSE TRAIN / REVERSE TRAINING (Table provided for time and level settings)

9) RANDOM / RANDOM (ANDES 5 ONLY):

Specially designed program based on a table that simulates random resistance changes.

10) CONSTANT WATTS / WATTS:

This workout automatically adjusts resistance to keep you within a specific watt range, maintaining your desired training intensity.

  1. Select the WATT program using [arrow keys] and press ENTER.
  2. Define a time using [arrow keys] and press ENTER.
  3. Select the desired wattage using [arrow keys] and press ENTER.
  4. Then press START to begin the program.

11) INTERVAL WATT / INTERVAL WATT (ANDES 7i ONLY):

Here you can choose a high and a low WATT value. The interval program then alternates between these two values, making the workout very intense and effective.

  1. Select the INTERVAL WATT program using [arrow keys] and press ENTER.
  2. Define a time using [arrow keys] and press ENTER.
  3. Select the low watt target value and press ENTER.
  4. Select the high watt target value and press ENTER.
  5. Then press Start to begin the program.

12) THR ZONE / TARGET HEART RATE ZONE:

Simulate the intensity of your favorite sport, as the program's resistance automatically adjusts to keep you within a given target heart rate zone. (It is recommended to wear a chest strap during this workout. You can purchase this chest strap separately from your dealer.)

  1. Select the THR Zone program using [arrow keys] and press ENTER.
  2. Define a time using [arrow keys] and press ENTER.
  3. The HEART RATE window flashes and displays a preset target heart rate of 80 beats per minute. Select your target heart rate (from the pulse training table) using [arrow keys] and press ENTER.
  4. To start the program, press START ►II.

HEART RATE TRAINING / HEART RATE TRAINING

The first step in determining the correct intensity of your workout is to establish your maximum heart rate (max HR = 220 - your age). This age-based method provides an average statistical prediction of your maximum heart rate and is a good method for the majority of users, especially for those who are new to heart rate training. The most precise and accurate way to determine a person's maximum HR is through a medical test by a cardiologist or sports therapist who tests maximum exertion capacity. If you are over 40 and overweight, have had a primarily sedentary lifestyle for several years, or have a family history of cardiovascular disease, a medical test is recommended. This table provides examples for the heart rate range of a 30-year-old training in 5 different heart rate zones. For example, the maximum heart rate of a 30-year-old is: 220 - 30 = 190 beats per minute, and 90% of max HR is 190 x 0.9 = 171 beats per minute.

Example of Target Heart Rate Zone (Age: 30 years)

VERY HARD 90-100% < 5 MIN. 171-190 BEATS PER MINUTE Fit individuals and for competitive training
HARD 80-90% 2-10 MIN. 152-171 BEATS PER MINUTE Shorter workouts
MODERATE 70-80% 10-40 MIN. 133-152 BEATS PER MINUTE Medium-length workouts
LIGHT 60-70% 40-80 MIN. 114-133 BEATS PER MINUTE Longer and more frequent shorter workouts
VERY LIGHT 50-60% 20-40 MIN. 104-114 BEATS PER MINUTE Weight control and active recovery

Note: The heart rate program is based on your target heart rate. Resistance changes automatically depending on your pedaling speed.

13) % THR / % TARGET HEART RATE (ANDES 7i ONLY):

Beneficial for weight loss by maintaining the optimal training intensity for fat burning. Resistance is adjusted to keep you within your target heart rate zone. First, enter your personal data (your equipment will automatically calculate your maximum training heart rate), then select the percentage of your maximum heart rate at which you want to train. (It is recommended to wear a chest strap during this workout. You can purchase this chest strap separately from your dealer.)

14) STRENGTH BUILDER / STRENGTH BUILDER (ANDES 7i ONLY):

Gradual improvement of muscle strength with a preset program. Time-based program with 20 intensity levels to choose from. The user defines the time and resistance using the arrow keys and presses ENTER.

15) CUSTOM / CUSTOM:

User-adjustable workout, workout duration is 15 minutes.

  1. First, enter the program settings. The profile display guides you through all settings.
  2. Use the arrow keys to adjust resistance. Press ENTER to confirm values.
  3. The console shows your current number of completed segments and guides you through segments 1 to 15.
  4. After entering all settings, press START ►II.
  5. The program will reset if you press and hold ENTER for 5 seconds.

Using Your Media Player

  1. Plug your included AUDIO ADAPTER CABLE into the audio jack on the console and the headphone jack on your media player.
  2. Change playback settings directly on the media player.
  3. Unplug the audio adapter cable when not in use.

Synchronizing with Passport

  1. Use the arrow keys on the Passport remote control and scroll to the Setup icon. Then press Select.
  2. Follow the on-screen instructions. Press and hold the Passport Quick Select button on the console for 3-5 seconds.
  3. If synchronization is successful, you will see the PASSPORT icon on the console display.
  4. The message on the screen will inform you whether the connection was successful or not.

ENERGY SAVER / ENERGY SAVER MODE

This equipment features an energy saver mode. When the energy saver mode is activated, the display automatically enters standby mode (energy saver mode) after 15 minutes of inactivity. This feature saves energy because a large portion of the power flow to the equipment is interrupted until a button on the console is pressed.

Andes 5 Spare Parts List

(Exploded view diagram of the Andes 5 elliptical trainer with numbered parts)

NO. ENGLISH DESCRIPTION QTY. NO. ENGLISH DESCRIPTION QTY.
B24 BEARING; DRY; PAP 2015; SHUN DE; SHUN DE 2 11 LINK ARM SET;SEMI-ASSY;LEFT;S-EP580; 1
B26 ADJUSTABLE LEVELER 4 12 LINK ARM SET;SEMI-ASSY; RIGHT;S-EP580; 1
B28 TRANSPORTS WHEEL ;PC; BLACK; FC16; 2 AJ1 CRANK SET;WELDING; EP543-1US; 2
B29 PULL PIN; EP247 1 J03 COVER; CRANK;HIPS; Q520-7-3; EP580-2KM; 2
B30 CLIP CC S-12 EXTERNAL 1 J05 SCREW;SH;M10X60L-22L; HS; BED; G12.9; 2
B31 SPRING; CMP; Φ1.2ΧΦ14.5X17.0LX8.5N;SWP;WZN 1 J06 NUT;M10X1.5P; G10;BLACK ANNODIZED; 2
B32 AIR STICK; SLOW-DROP;75KG; MAX(331)MIN(213 1 J07 WASHER; FLAT; ΦΧ10.2ΧΦΧ15.0X1.5T;BL ZN;R 4
B39 COVER;STABILIZER TUBE; FRONT; HIPS, PH-88; 1 J04 SCREW;BH;M5X0.8PX8L;CT;PH;BZN; 6
B40 COVER;STABILIZER TUBE; MID; HIPS, PH-88;E 1 J08 SCREW;BH; Φ4X15L; SM;PH;BZN;POT 2
B41 SCREW;BH;Φ4X15L;SM;PH;BZN;POT 4 J09 COVER;CRANK; INNER;HIPS; Q520-7-3; EP580-2 2
B42 SCREW;BH;M8X1.25PX30L;HS;CRMO; 2 J10 WASHER;WW; Φ17.2ΧΦ22.5X0.5T;65MN 2
B43 NUT; NLK; M8X1.25P;BZN; 4 Q01 SIDE COVER-EXREAWORK; LEFT;SCREEN PRINT; 1
B45 WASHER; FLAT; ΦΧ8.2ΧΦΧ20.0X1.5T;BL ZN;RO 2 Q02 SIDE COVER-EXREAWORK;RIGHT;SCREEN PRINT 1
B51 WASHER;FLT; Φ12.0X25.0X1.5T;TFN; 1 Q10 COVER; CONSOEL MAST; BACK; HIPS;Q520-7-3;E 1
B52 SCREW;SPECIAL; M8X10L/Φ10X41L; MACHINE THR 1 Q09 COVER;CONSOEL MAST;FRONT;HIPS;Q520-7-3; 1
G06 ARM REST SET;SEMI-ASSY; LEFT DOWN;S-EP580; 1 Q04 SCREW;BH; Φ4X15L; SM;PH;WZN;POT 9
7 ARM REST SET;SEMI-ASSY; LEFT DOWN;S-EP580; 1 Q05 CLIP; STANDARD;WUSN-4039; 8
8 ARM REST SET;SEMI-ASSY; RIGHT DOWN;S-EP580; 1 Q06 BRACKET SIDE COVER 3
9 ARM REST SET;SEMI-ASSY; LEFT UP;S-EP580 1 Q07 SCREW;TRHW;OX4X15L; TC; PH;BED; POT;GRE 4
10 ARM REST SET;SEMI-ASSY; RIGHT UP;S-EP580 1 Q08 FIX PILLAR;PP;TM81 2
11 LINK ARM SET;SEMI-ASSY;LEFT;S-EP580; 1 P02 WIRE; SENSOR; 700MM;CYLINDRICAL MAGNETI 1
12 LINK ARM SET;SEMI-ASSY; RIGHT;S-EP580; 1 P11 CONSOLE WIRE;UP1;280MM;CKM254301-8P 1
AJ1 CRANK SET;WELDING; EP543-1US; 2 P03 SCREW;BH; Φ4X10L; TC; PH; BAN;POT 1
J03 COVER; CRANK;HIPS; Q520-7-3; EP580-2KM; 2 P04 POWER WIRE;DC;600MM(DC+CKM 25430101-2P) 1
J05 SCREW;SH;M10X60L-22L; HS; BED; G12.9; 2 P06 TIE STRAP ADHESIVE; 1
J06 NUT;M10X1.5P; G10;BLACK ANNODIZED; 2 P17 WIRELESS RECEIVER SET 1
J07 WASHER; FLAT; ΦΧ10.2ΧΦΧ15.0X1.5T;BL ZN;R 4 P07 CABLE TIE;NYLON; BLACK; 160L 3
J04 SCREW;BH;M5X0.8PX8L;CT;PH;BZN; 6 P08 CABLE TIE;NYLON; 300L; WHITE 1
J08 SCREW;BH; Φ4X15L; SM;PH;BZN;POT 2 P10 PLATE POWER SOCKET 1
J09 COVER;CRANK; INNER;HIPS; Q520-7-3; EP580-2 2 P05 SCREW;BUTTON HEAD; P4X10L; SHEET METAL THR 4
J10 WASHER;WW; Φ17.2ΧΦ22.5X0.5T;65MN 2 P11 WIRE; POWER SOCKET SET; 150 150 300;250 1
Q01 SIDE COVER-EXREAWORK; LEFT;SCREEN PRINT; 1 P12 WIRE; ELECTROMAGNET PWR;400MM;EL-2Y VH 1
Q02 SIDE COVER-EXREAWORK;RIGHT;SCREEN PRINT 1 P13 FILTER; POWER;3A;220V;BF1106C-3A-02;ERP 1
Q10 COVER; CONSOEL MAST; BACK; HIPS;Q520-7-3;E 1 P18 WIRE; CTRL BOARD PWR;BLACK; 250LOCK700L 1
Q09 COVER;CONSOEL MAST;FRONT;HIPS;Q520-7-3; 1 P19 WIRE; CTRL BOARD PWR; WHITE;250LOCK700L 1
Q04 SCREW;BH; Φ4X15L; SM;PH;WZN;POT 9 P20 CONTROLLER;DIGITAL BRAKING SYSTEM; EXTRA- 1
Q05 CLIP; STANDARD;WUSN-4039; 8 P09 SCREW;BH; Φ4X15L; TC; PH; BAN;POT 4
Q06 BRACKET SIDE COVER 3 P14 SCREW;BH; Φ4X12L; SM;PH;YZN;POT 1
Q07 SCREW;TRHW;OX4X15L; TC; PH;BED; POT;GRE 4 P21 EXTERNAL PWR;IN; 1.5MM;2M; 1
Q08 FIX PILLAR;PP;TM81 2 P21 EXTERNAL PWR;NEW ZEALAND; 1.5MM;2M; 1
P02 WIRE; SENSOR; 700MM; CYLINDRICAL MAGNETI 1 P21 EXTERNAL PWR;EUROPE; 1.5MM;2M 1
P11 CONSOLE WIRE; UP1;280MM;CKM254301-8P 1 P21 EXTERNAL PWR;CHINA; 1.5MM;2M 1
P03 SCREW;BH; Φ4X10L; TC; PH; BAN;POT 1 P21 EXTERNAL PWR; HK/KW/GB;1.5MM;2M; 1
P04 OVERCURRENT BREAKER;3A; 125V/250V; CITY B 1 P21 EXTERNAL PWR; US/CA/TH; 16AWG;2M 1
P11 WIRE; POWER SOCKET SET; 150 150 300;250 1 P21 EXTERNAL PWR WIRE SET; ISRAEL; 1.5MM;2 1
P12 WIRE; ELECTROMAGNET PWR;400MM;EL-2Y VH 1 P21 EXTERNAL PWR; ARGENTINA; 1.5MM;2M; 1
P13 FILTER; POWER;3A;220V;BF1106C-3A-02;ERP 1 P21 EXTERNAL PWR;SOUTH AFRICA; 1.5MM; 1
P18 WIRE; CTRL BOARD PWR;BLACK; 250LOCK700L 1 P21 EXTERNAL PWR; SWEDEN;2M;1.5MM 1
P19 WIRE; CTRL BOARD PWR; WHITE;250LOCK700L 1 P21 EXTERNAL PWR; BR; LENGTH:2M; 1.5MM2 1
P20 CONTROLLER;DIGITAL BRAKING SYSTEM; EXTRA- 1 P21 WIRE; EXTERNAL PWR;SET;CHILE USED; JIS2 U 1
P09 SCREW;BH; Φ4X15L; TC; PH; BAN;POT 4
P14 SCREW;BH; Φ4X12L; SM;PH;YZN;POT 1
P21 EXTERNAL PWR;IN; 1.5MM;2M; 1
P21 EXTERNAL PWR;NEW ZEALAND; 1.5MM;2M; 1
P21 EXTERNAL PWR;EUROPE; 1.5MM;2M 1
P21 EXTERNAL PWR;CHINA; 1.5MM;2M 1
P21 EXTERNAL PWR; HK/KW/GB;1.5MM;2M; 1
P21 EXTERNAL PWR; US/CA/TH; 16AWG;2M 1
P21 EXTERNAL PWR WIRE SET; ISRAEL; 1.5MM;2 1
P21 EXTERNAL PWR; ARGENTINA; 1.5MM;2M; 1
P21 EXTERNAL PWR;SOUTH AFRICA; 1.5MM; 1
P21 EXTERNAL PWR; SWEDEN;2M;1.5MM 1
P21 EXTERNAL PWR; BR; LENGTH:2M; 1.5MM2 1
P21 WIRE; EXTERNAL PWR;SET;CHILE USED; JIS2 U 1
B37 WASHER; FLAT; ΦΧ12.0ΧΦΧ23.0X2.5T;BLACK ZI 4
B38 SCREW;SH;M10X1.5PX20L;HS;BZN; 4
Z09 SCREW;BH;M8X70L-12L; HS;G8.8;BZN;BP; 2
JOZ NUT; NLK; M8X1.25P;BZN; 3
12 CONSOLE SET;SEMI-ASSY;S-EP581; 1
13 DRIVE SET;SEMI-ASSY;S-EP581; 1
14 FLYWHEEL SET;SA; EP257B; 1
15 CONSOLE SET;SEMI-ASSY; EP581-2KM; 1
V04 SAFETY LABEL;CE; EP581-2KM 1

Andes 7i Spare Parts List

(Exploded view diagram of the Andes 7i elliptical trainer with numbered parts)

NO. ENGLISH DESCRIPTION QTY. NO. ENGLISH DESCRIPTION QTY. NO. ENGLISH DESCRIPTION QTY. NO. ENGLISH DESCRIPTION QTY.
B32 AIR STICK;SLOW-DROP;75KG; MAX(331)MIN(213 1 10 B41 SCREW;BH;Φ4X15L; SM;PH;BZN;POT 4 G06 ARM REST SET;SEMI-ASSY; RIGHT UP;S-EP581 1 P05 SCREW;BUTTON HEAD; P4X10L; SHEET METAL THR 4
B38 SCREW;SH;M10X1.5PX20L;HS;BZN; 4 2 P03 SCREW;BH; Φ4X10L; TC; PH; BAN;POT 1 WRENCH; HEX;L-TYPE;#8MMX147L; 1 P08 CABLE TIE;NYLON;300L;WHITE 1
B42 SCREW;BH;M8X1.25PX30L;HS;CRMO; 2 11 LINK ARM SET;SEMI-ASSY;LEFT;S-EP581; 1 P15 CONSOLE WIRE; UP1;280MM;CKM254301-8P 1 Z09 SCREW;BH;M8X70L-12L;HS;G8.8;BZN;BP; 2
B43 NUT; NLK; M8X1.25P;BZN; 4 12 LINK ARM SET;SEMI-ASSY; RIGHT;S-EP581; 1 P02 WIRE; SENSOR; 700MM; CYLINDRICAL MAGNETI 1 Z02 NUT; NLK;M8X1.25P;BZN; 2
B45 WASHER; FLAT; ΦΧ8.2ΧΦΧ20.0X1.5T;BL ZN;RO 2 AJ1 CRANK SET; WELDING; EP543-1US; 2 P04 OVERCURRENT BREAKER;3A; 125V/250V; CITY B 1 Z07 WASHER; FLAT; ΦΧ8.6ΧΦΧ26.0X2.0T;BL ZN;RO 2
B39 COVER;STABILIZER TUBE; FRONT; HIPS, PH-88; 1 J03 COVER; CRANK; HIPS; Q520-7-3; EP580-2KM; 2 P11 WIRE; POWER SOCKET SET; 150 150 300;250 1 Z10 WASHER; FLAT; ΦΧ8.2ΧΦΧ20.0X1.5T;BL ZN;RO 2
B40 COVER;STABILIZER TUBE; MID; HIPS, PH-88;E 1 J05 SCREW;SH;M10X60L-22L; HS; BED; G12.9; 2 P12 WIRE; ELECTROMAGNET PWR;400MM;EL-2Y VH 1 Z04 WASHER; FLT; Φ16.0X25.0X1.5T; 4
B28 TRANSPORTS WHEEL; PC; BLACK; FC16; 2 J06 NUT;M10X1.5P; G10;BLACK ANNODIZED; 2 P13 FILTER; POWER;3A;220V;BF1106C-3A-02;ERP 1 Z05 SCREW;BH;M8X20L; HS;BZN;BP;G8.8; 2
B26 ADJUSTABLE LEVELER 4 J07 WASHER; FLAT; ΦΧ10.2ΧΦΧ15.0X1.5T;BL ZN;R 4 P18 WIRE; CTRL BOARD PWR;BLACK; 250LOCK700L 1 Z08 RING; RUBBER; Ψ26.2XΨ16.20X11.50 2
B24 BEARING; DRY; PAP 2015;SHUN DE; SHUN DE 2 J04 SCREW;BH; M5X0.8PX8L;CT;PH;BZN; 6 P19 WIRE; CTRL BOARD PWR; WHITE;250LOCK700L 1 WRENCH; HEX L-TYPE;5MM 52X140L; BLACK OX 1
B30 CLIP CC S-12 EXTERNAL 1 J08 SCREW;BH; Φ4X15L; SM;PH;BZN;POT 2 P20 CONTROLLER;DIGITAL BRAKING SYSTEM; EXTRA- 1 WRENCHOPEN-TYPE#13#15**DISC USE 005382-Z 1
B29 PULL PIN; EP247 1 J09 COVER; CRANK;INNER;HIPS; Q520-7-3; EP580-2 2 P09 SCREW;BH; Φ4X15L; TC; PH; BAN;POT 4
B31 SPRING;CMP; Φ1.2ΧΦ14.5X17.0LX8.5N;SWP; WZN 1 J10 WASHER;WW; Φ17.2ΧΦ22.5X0.5T;65MN 2 P14 SCREW;BH; Φ4X12L; SM;PH;YZN;POT 1
B35 SCREW;BH;M8X1.25PX45L;HS;BZN; 2 Q01 SIDE COVER-EXREAWORK;LEFT;SCREEN PRINT; 1 P21 EXTERNAL PWR;IN; 1.5MM;2M; 1
B36 NUT;HEX;3/8-16UNC-4T;SS41;BLACK ANNODIZE 4 Q02 SIDE COVER-EXREAWORK;RIGHT;SCREEN PRINT 1 P21 EXTERNAL PWR;NEW ZEALAND; 1.5MM;2M; 1
B51 WASHER; FLT;$12.0X25.0X1.5T;TFN; 1 Q05 SCREW;ΒΗ; Φ4X15L;TC; PH; BAN;POT 9 P21 EXTERNAL PWR;EUROPE; 1.5MM;2M 1
B52 SCREW;SPECIAL;M8X10L/Φ10X41L; MACHINE THR 1 Q06 CLIP; STANDARD;WUSN-4039; 8 P21 EXTERNAL PWR;CHINA; 1.5MM;2M 1
1 CONSOLE MAST SET;SEMI-ASSY;S-EP581; 1 Q07 BRACKET SIDE COVER 3 P21 EXTERNAL PWR; HK/KW/GB;1.5MM;2M; 1
2 FRAME SET;SEMI-ASSY;BACK;S-EP581; 1 Q08 SCREW; TRHW;OX4X15L;TC;PH;BED; POT; GRE 4 P21 EXTERNAL PWR; US/CA/TH; 16AWG;2M 1
3 PEDAL ARM SET;SEMI-ASSY;LEFT;S-EP581; P02 WIRE; SENSOR; 700MM; CYLINDRICAL MAGNETI 1 P21 EXTERNAL PWR WIRE SET; ISRAEL; 1.5MM;2 1
4 PEDAL ARM SET;SEMI-ASSY; RIGHR;S-EP581; 1 P11 CONSOLE WIRE; UP1;280MM;CKM254301-8P 1 P21 EXTERNAL PWR; ARGENTINA; 1.5MM;2M; 1
7 ARM REST SET;SEMI-ASSY;LEFT DOWN;S-EP581; 1 P03 SCREW;BH; Φ4X10L; TC; PH; BAN;POT 1 P21 EXTERNAL PWR;SOUTH AFRICA; 1.5MM; 1
8 ARM REST SET;SEMI-ASSY; RIGHT DOWN;S-EP581; 1 P04 OVERCURRENT BREAKER;3A; 125V/250V; CITY B 1 P21 EXTERNAL PWR; SWEDEN;2M;1.5MM 1
9 ARM REST SET;SEMI-ASSY; LEFT UP;S-EP581 1 P11 WIRE; POWER SOCKET SET; 150 150 300;250 1 P21 EXTERNAL PWR; BR; LENGTH:2M; 1.5MM2 1
10 ARM REST SET;SEMI-ASSY; RIGHT UP;S-EP581 1 P12 WIRE; ELECTROMAGNET PWR;400MM;EL-2Y VH 1 P21 WIRE; EXTERNAL PWR;SET;CHILE USED; JIS2 U 1
11 LINK ARM SET;SEMI-ASSY;LEFT;S-EP581; 1 P13 FILTER; POWER;3A;220V;BF1106C-3A-02;ERP 1
12 LINK ARM SET;SEMI-ASSY; RIGHT;S-EP581; 1 P18 WIRE; CTRL BOARD PWR;BLACK; 250LOCK700L 1
AJ1 CRANK SET; WELDING; EP543-1US; 2 P19 WIRE; CTRL BOARD PWR; WHITE;250LOCK700L 1
J03 COVER; CRANK; HIPS; Q520-7-3; EP580-2KM; 2 P20 CONTROLLER;DIGITAL BRAKING SYSTEM; EXTRA- 1
J05 SCREW;SH;M10X60L-22L; HS; BED; G12.9; 2 P09 SCREW;BH; Φ4X15L; TC; PH; BAN;POT 4
J06 NUT;M10X1.5P; G10;BLACK ANNODIZED; 2 P14 SCREW;BH; Φ4X12L; SM;PH;YZN;POT 1
J07 WASHER; FLAT; ΦΧ10.2ΧΦΧ15.0X1.5T;BL ZN;R 4 P21 EXTERNAL PWR;IN; 1.5MM;2M; 1
J04 SCREW;BH; M5X0.8PX8L;CT;PH;BZN; 6 P21 EXTERNAL PWR;NEW ZEALAND; 1.5MM;2M; 1
J08 SCREW;BH; Φ4X15L; SM;PH;BZN;POT 2 P21 EXTERNAL PWR;EUROPE; 1.5MM;2M 1
J09 COVER; CRANK;INNER;HIPS; Q520-7-3; EP580-2 2 P21 EXTERNAL PWR;CHINA; 1.5MM;2M 1
J10 WASHER;WW; Φ17.2ΧΦ22.5X0.5T;65MN 2 P21 EXTERNAL PWR; HK/KW/GB;1.5MM;2M; 1
Q01 SIDE COVER-EXREAWORK;LEFT;SCREEN PRINT; 1 P21 EXTERNAL PWR; US/CA/TH; 16AWG;2M 1
Q02 SIDE COVER-EXREAWORK;RIGHT;SCREEN PRINT 1 P21 EXTERNAL PWR WIRE SET; ISRAEL; 1.5MM;2 1
Q10 COVER; CONSOEL MAST; BACK; HIPS;Q520-7-3;EP580 1 P21 EXTERNAL PWR; ARGENTINA; 1.5MM;2M; 1
Q09 COVER; CONSOEL MAST;FRONT;HIPS;Q520-7-3;EP580 1 P21 EXTERNAL PWR;SOUTH AFRICA; 1.5MM; 1
Q04 SCREW;BH; Φ4X15L; SM;PH;WZN;POT 9 P21 EXTERNAL PWR; SWEDEN;2M;1.5MM 1
Q05 CLIP; STANDARD;WUSN-4039; 8 P21 EXTERNAL PWR; BR; LENGTH:2M; 1.5MM2 1
Q06 BRACKET SIDE COVER 3 P21 WIRE; EXTERNAL PWR;SET;CHILE USED; JIS2 U 1
Q07 SCREW; TRHW;OX4X15L; TC; PH;BED; POT; GRE 4
Q08 FIX PILLAR;PP;TM81 2
P02 WIRE; SENSOR; 700MM; CYLINDRICAL MAGNETI 1
P11 CONSOLE WIRE; UP1;280MM;CKM254301-8P 1
P03 SCREW;BH; Φ4X10L; TC; PH; BAN;POT 1
P04 OVERCURRENT BREAKER;3A; 125V/250V; CITY B 1
P11 WIRE; POWER SOCKET SET; 150 150 300;250 1
P12 WIRE; ELECTROMAGNET PWR;400MM;EL-2Y VH 1
P13 FILTER; POWER;3A;220V;BF1106C-3A-02;ERP 1
P18 WIRE; CTRL BOARD PWR;BLACK; 250LOCK700L 1
P19 WIRE; CTRL BOARD PWR; WHITE;250LOCK700L 1
P20 CONTROLLER;DIGITAL BRAKING SYSTEM; EXTRA- 1
P09 SCREW;BH; Φ4X15L; TC; PH; BAN;POT 4
P14 SCREW;BH; Φ4X12L; SM;PH;YZN;POT 1
P21 EXTERNAL PWR;IN; 1.5MM;2M; 1
P21 EXTERNAL PWR;NEW ZEALAND; 1.5MM;2M; 1
P21 EXTERNAL PWR;EUROPE; 1.5MM;2M 1
P21 EXTERNAL PWR;CHINA; 1.5MM;2M 1
P21 EXTERNAL PWR; HK/KW/GB;1.5MM;2M; 1
P21 EXTERNAL PWR; US/CA/TH; 16AWG;2M 1
P21 EXTERNAL PWR WIRE SET; ISRAEL; 1.5MM;2 1
P21 EXTERNAL PWR; ARGENTINA; 1.5MM;2M; 1
P21 EXTERNAL PWR;SOUTH AFRICA; 1.5MM; 1
P21 EXTERNAL PWR; SWEDEN;2M;1.5MM 1
P21 EXTERNAL PWR; BR; LENGTH:2M; 1.5MM2 1
P21 WIRE; EXTERNAL PWR;SET;CHILE USED; JIS2 U 1
B37 WASHER; FLAT; ΦΧ12.0ΧΦΧ23.0X2.5T;BLACK ZI 4
B38 SCREW;SH;M10X1.5PX20L;HS;BZN; 4
Z09 SCREW;BH;M8X70L-12L; HS;G8.8;BZN;BP; 2
JOZ NUT; NLK; M8X1.25P;BZN; 3

Disposal Information

Disposal Information: HORIZON Fitness products are recyclable. At the end of its useful life, please dispose of the equipment properly (local collection point).

Contact

Johnson Health Tech. GmbH
Europaallee 51
50226 Frechen

General Information:

Phone: 02234 - 9997 - 100
Email: info@johnsonfitness.eu

Technical Hotline:

Phone: 02234 - 9997 - 500
Email: support@johnsonfitness.eu
Telefax: 02234 - 9997 - 200

www.johnsonfitness.eu

Models: Andes 7i Elliptical Trainer, Andes 7i, Elliptical Trainer, Trainer

File Info : application/pdf, 23 Pages, 7.62MB

PDF preview unavailable. Download the PDF instead.

Andes 5 und 7i Bedienungsanleitung Adobe InDesign CS6 (Windows) Adobe PDF Library 10.0.1

Related Documents

Preview Horizon Fitness Endurance 4 & 5 Elliptical Owner's Manual
Comprehensive owner's manual for Horizon Fitness Endurance 4 and Endurance 5 elliptical trainers, covering assembly, operation, programs, and maintenance.
Preview Horizon Fitness Club Series Elliptical User's Guide
Comprehensive user's guide for Horizon Fitness Club Series ellipticals (CSE3.6, CSE4.6), covering assembly, operation, maintenance, troubleshooting, and warranty information.
Preview Horizon Fitness 5.0U Upright Bike Owner's Manual - Operation, Assembly & Safety
Discover how to safely operate, adjust, and assemble your Horizon Fitness 5.0U Upright Bike with this comprehensive owner's manual. Includes detailed instructions and safety guidelines.
Preview Horizon 7.0AT Treadmill Owner's Manual
This owner's manual provides comprehensive instructions for the Horizon 7.0AT Treadmill, covering safety precautions, assembly, operation, console features, and various workout profiles. It guides users through setup, safe usage, and maximizing their fitness experience.
Preview Horizon Fitness 5.0R Recumbent Bike Owner's Manual
Comprehensive owner's manual for the Horizon Fitness 5.0R Recumbent Bike, covering assembly, operation, safety, and maintenance instructions.
Preview Horizon Bike Console OTA Software Update Guide
Step-by-step instructions to update the Horizon 5.0IC, 7.0IC, 5.0U, and 5.0R bike console software over-the-air using the nRF Connect for Mobile app on an iPhone. Includes visual descriptions and required steps.
Preview Horizon Fitness 7.0 AT Treadmill Owner's Manual
This owner's manual provides comprehensive instructions for the Horizon Fitness 7.0 AT Treadmill, covering assembly, operation, safety precautions, and maintenance. Learn how to set up, use, and care for your treadmill to maximize your fitness goals.
Preview Horizon Fitness HZ Series Treadmill User's Guide
Comprehensive user's guide for the Horizon Fitness HZ Series treadmills, including models T71 and T72. Covers assembly, safety precautions, operation, maintenance, troubleshooting, and warranty information.