Wharfedale Pro EVP-XP Series
Professional Loudspeaker User Manual
This User Manual covers the following models: EVP-X12P, EVP-X12PM, EVP-X15P, EVP-X15PM, EVP-X215P, EVP-X15PB, EVP-X18PB Subwoofers.
Contents:
- Page 1: Warning and Safety Instructions
- Page 2: Specifications/Operating and Use
- Page 3: Product Features/ EVP-X12PM/15PM Panel
- Page 4: EVP-X18PB Rear Panel Diagram
- Page 5: EVP-X15PB and EVP-X18PB Operation
- Page 6: Single EVP-X18PB with Stereo Mid/High Active System and Stereo Active Sub and Mid/High System
- Page 7: Stereo Passive Mid/High Speaker with Active Sub System and EVP-X15P/18PB Block Diagram
⚠️ WARNING & SAFETY INSTRUCTIONS ⚠️
- READ INSTRUCTIONS carefully before operating this product.
- RETAIN these instructions.
- COMPLY WITH WARNINGS - All warnings and instructions for this product should be adhered to.
- WATER & MOISTURE - This Wharfedale Pro unit should not be used near liquids. It should not have liquids placed on or in close proximity as there are DANGEROUS VOLTAGES present.
- VENTILATION/AIR FLOW: This Wharfedale Pro unit should not have its heat sinks obstructed from air flow. It should not be situated in a built-in installation that may hamper air flow to the heat sinks. It should not be placed near heat sources.
- POWER SUPPLY: This Wharfedale Pro unit should be only connected to a power supply as stated on the unit. Power supply cables should be routed where they will not be walked on or pinched by objects placed adjacent or upon them.
- ELECTRIC SHOCK: Care should be taken that the grounding of this unit is NOT defeated. Do not use this unit's power cable with an extension cable unless the pins can be fully inserted.
- CABLES - Use quality screened cables for signal connections.
- RIGGING, SUSPENDING, MOUNTING: The rigging, suspension or mounting of this speaker system can expose members of the public to serious health risks and even death. UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE MOUNT THIS SYSTEM UNLESS YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT SAFETY REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT PROPERLY QUALIFIED OR DO NOT KNOW OF PERTINENT REGULATIONS, CONSULT QUALIFIED PERSONNEL FOR ADVICE AND ASSISTANCE.
- CAUTION: These professional loudspeaker systems are capable of generating very high sound pressure levels. Use care with placement and operation to avoid exposure to excessive levels that can cause permanent hearing damage.
- SERVICING - The user should not attempt to service this product except that mentioned in this manual.
Unpacking
All Wharfedale Pro products are fully checked before leaving the factory. After unpacking please inspect cabinets for any physical damage. Please retain the shipping carton if possible and internal packing material in case the unit needs to be returned. Please check as soon as possible the unit is functioning. In the event of any damage please contact your dealer immediately so that a written claim for damages can be made.
Wharfedale Pro Limited Warranty*
Wharfedale Pro EVP-XP Series loudspeaker systems are warranted to be clear of manufacturing or materials defects for a period of one year from the original date of purchase. In the event of malfunction, contact your authorised Wharfedale Professional dealer or distributor for information.
*Be aware that warranty details may differ from country to country. Contact your dealer or distributor for information. These terms do not infringe your statutory rights.
Specifications
| Model Name | EVP-X12P | EVP-X12PM | EVP-X15P | EVP-X15PM | EVP-X215P | EVP-X15PB | EVP-X18PB |
|---|---|---|---|---|---|---|---|
| SYSTEM TYPE | 12" 2-way | 12" 2 way monitor | 15" 2-way | 15" 2-way monitor | 2x15" 2 way | 15" compact sub | 18" compact sub |
| FREQ RESP +/- 3 DB | 55 - 20kHz | 50Hz-20kHz | 45 - 20kHz | 50 - 20kHz | 40 - 20kHz | 45 - 200Hz | 40 -200Hz |
| FINISH MATERIAL | Black carpet | Black carpet | Black carpet | Black carpet | Black carpet | Black carpet | Black carpet |
| TRIPOD STAND BOTTOM | Yes | No | Yes | No | No | No | No |
| TRIPOD STAND TOP | No | No | No | No | No | Yes | Yes |
| INPUTS: INPUT A | Switchable balanced mic or line level input | Line level input | Line level input | Line level input | Switchable balanced mic or line level input | Line level input | Line level input |
| INPUTS: INPUT B | NA | NA | NA | NA | Line level input | NA | NA |
| INPUTS: SPEAKER LEVEL INPUT | NA | NA | NA | NA | NA | 1/4" TS Phone Jack | 1/4" TS Phone Jack |
| INPUT CONNECTORS: INPUT A | Combined Jack and XLR | Combined Jack and XLR | Combined Jack and XLR | Combined Jack and XLR | Combined Jack and XLR | Combined Jack | Combined Jack |
| INPUT CONNECTORS: INPUT B | XLR & RCA Socket | NA | NA | NA | XLR & RCA Socket | Combined Jack | Combined Jack |
| INPUT SENSITIVITY: MIC | 5mV | 5mV | 5mV | 5mV | 5mV | NA | NA |
| INPUT SENSITIVITY: RCA | 0.5V | 0.5V | 0.5V | 0.5V | 0.5V | NA | NA |
| INPUT SENSITIVITY: LINE | 0.775V | 0.775V | 0.775V | 0.775V | 0.775V | 0.775V | 0.775V |
| INPUT IMPEDANCE: MIC | 470 OHMS | 470 OHMS | 470 OHMS | 470 OHMS | 470 OHMS | 470 OHMS | 470 OHMS |
| INPUT IMPEDANCE: LINE INPUT A | 47K | 47K | 47K | 47K | 47K | 10K | 10K |
| INPUT IMPEDANCE: LINE INPUT B | 10kohms | 10K | 10K | 10K | 10K | 10K | 10K |
| LINE OUTPUT TYPE | Balanced Male XLR connector | Balanced Male XLR connector | Balanced Male XLR connector | Balanced Male XLR connector | Balanced Male XLR connector | Balanced Male XLR connector | Balanced Male XLR connector |
| LINE OUTPUT HIGH PASS FILTER | HF Shelving +/-12dB@10KHZ | HF Shelving +/-12dB@10KHZ | HF Shelving +/-12dB@10KHZ | HF Shelving +/-12dB@10KHZ | HF Shelving +/-12dB@10KHZ | NA | NA |
| MAIN EQ | 5 band graphic EQ | LF Shelving +/-12dB @80Hz | 5 band graphic EQ | LF Shelving +/-12dB @80HZ | LF Shelving +/-12dB @80HZ | LPF: 150HZ, 24dB | LPF: 150Hz, 24dB |
| ACTIVE CROSSOVER | NA | NA | NA | NA | NA | NA | NA |
| PHASE SWITCH | NA | NA | NA | NA | 0 or 180° | 0 or 180° | 0 or 180° |
| AMPLIFIER POWER: CONTINUOUS | 300W | 300W | 400W | 400W | 400W | 400W | 400W |
| AMPLIFIER POWER: PEAK | 500W | 500W | 600W | 600W | 600W | 600W | 600W |
| EXTENSION SPEAKER OUTPUT | NA | 1 | NA | 1 | NA | NA | NA |
| PROTECTION TYPE | Dynamic/AGC | Dynamic/AGC | Dynamic/AGC | Dynamic/AGC | Dynamic/AGC | Dynamic/AGC | Dynamic/AGC |
| POWER ON INDICATOR | GREEN LED | GREEN LED | GREEN LED | GREEN LED | GREEN LED | GREEN LED | GREEN LED |
| SYSTEM DYNAMIC AGC | ORANGE LED | ORANGE LED | ORANGE LED | ORANGE LED | ORANGE LED | ORANGE LED | ORANGE LED |
| DIMENSION MM (HXWXD) | 590X430X370 | 560x424x441 | 675X460X450 | 645X445X473.5 | 1058X502X467 | 591X460X510 | 610X522X610 |
| WEIGHT (NET) KG | 22.9 | 22.5kg | 29.5 | 27.4 | 46.8 | 35.1 | 49.2 |
| WEIGHT (GROSS) KG | 25.6 | 25.1kg | 33.6 | 30.5 | 51.6 | 38.1 | 52.3 |
Operating/Use
- The EVP-X12P, X15P, X215P feature 2 x combined jack and XLR inputs. The two stereo inputs are mixed down to mono enabling the connection of stereo output products.
- Connect the provided power cable to the IEC mains connector on the rear of the cabinet.
- Connect the signal cable (balanced or unbalanced, see table and description) from the audio mixer or processor securely to your EVP-XP unit (the internal amplifier should be off, power down mode). Where possible, use quality connectors. Only use screened audio cable for the signal input from the audio mixer or processor. If possible, use balanced line signal leads for optimum quality (see description and table of balanced line operation).
- If using XLR CONNECTORS, insert the XLR until locked in. If using a jack plug, insert until secure.
- Power up the audio mixer or processor, ensuring connections are made.
- Power up the EVP-XP internal amplifier with levels set to zero. Confirm speakers are operating.
- The EVP-XP all feature a balanced Male XLR connector on the line output.
- The EVP-X12PM, X15PM has one speaker extension output allowing the addition of another speaker.
Product Features
Product Features of the EVP-XP Series:
- 300W RMS/500W Peak amplifier (EVP-X12P, EVP-X12PM)
- 400W RMS/600W Peak amplifier (EVP-X15P, 15PM, 215P)
- Thermal, DC fault and short circuit protection
- Hi/Low EQ control in the master section
- 5 Band Graphic EQ (EVP-X12PM/15PM only)
- External speaker output connector (EVP-X12PM/15PM only)
- Integral tripod stand adaptor (except monitors)
- Balanced line output
- Integral, preset limiter prevents clipping distortion
- Combined Jack and XLR balanced input connectors
- Power on and system AGC protect LED indicators
EVPX-15PB and EVPX-18PB Active Subwoofers
- Stereo line input and speaker level input available for the powered subwoofer
- Peak limiter that protects the amplifier and speaker from clipping.
- 0°, 180° Phase switch
- Built-in 600 watt (peak), 400 watt (continuous) amplifier
- Thermal, DC fault and short circuit protection
- Power on and system AGC protect LED indicators
- Integral, preset limiter prevents clipping and distortion. Line-level stereo inputs are summed before being sent to the subwoofer's internal amplifier. This feature allows the subwoofer to operate in stereo systems using a single subwoofer.
- A pair of integral 150Hz, 24dB/Oct crossovers to send a high-pass, balanced, line-level, stereo signal to a pair of powered satellite full-range speakers or an external amplifier for passive satellite speakers.
- A speaker-level, 1/4" TS phone jack is provided. This input is useful in applications, such as those employing powered mixers, in which it is more practical to bring a full-range, speaker-level signal to the subwoofer amplifier.
- The EVP-X15/18PB is a 15/18 inch direct-radiating powered subwoofer. A built-in 600 watt (peak) amplifier accepts stereo or mono line level inputs via balanced, XLR connectors as well as single channel speaker level input via a 1/4 inch phone jack. Integral signal processing includes a stereo crossover and limiting for the internal amplifier. A pair of XLR out-put connectors may be used to pass the input signals to another system or to send a high-pass, line-level stereo signal to a pair of powered, full-range speakers.
EVP-X12PM/15PM Panel & Description:
The rear panel of the EVP-X12PM/15PM features several controls and connectors:
- Level control: Adjusts the overall volume of the amplified signal.
- 5 band EQ: This Five-Band Graphic EQ allows boosting or cutting your signal by up to 12dB at specific frequency centers, useful for reducing low-frequency rumble or feedback.
- Parallel Line input and output: These two jacks provide a signal input to the unit and allow for daisy-chaining the signal to another EVP-X15PM or amplifier combination.
- Speaker out: A post EQ, powered output designed for speakers with a minimum impedance of 8 ohms. This output should only be connected to non-powered monitor speakers. The EVP-X15M is an ideal extension monitor.
- Power switch: Turns the unit on and off.
- AC Input connector: Connects the included line cord for AC power. Ensure connection to a properly grounded AC supply. Using an improper line voltage may damage the equipment. NEVER REMOVE OR CUT THE GROUND PIN OF THE LINE CORD PLUG.
- Fuse: If the fuse fails, it must be replaced with the same type and value to avoid equipment damage and prevent voiding the warranty.
The panel shows a layout with numbered controls: 1. Level control, 2. 5-band EQ, 3. Balanced Line Input/Output jacks, 4. Speaker Out, 5. Power switch, 6. AC Input connector, 7. Fuse holder.
EVP-X18PB Rear Panel Description
The rear panel of the EVP-X18PB features the following controls and connectors:
- Input A Connectors: Electronically balanced, XLR and 1/4" phone connectors for line-level input signal.
- Output A Connectors: Provide either a loop-thru or high-passed, line-level output.
- Speaker Level Input: A 1/4" phone jack for connecting speaker-level output from an amplifier or powered mixer.
- Volume Control: Adjusts the sound volume level.
- Output A&B Switch: Selects signal routing for Outputs A & B. Options are 'THRU' (direct pass-through) or 'HIGH PASS' (100Hz, 24dB/Oct filter).
- Phase Switch: Selects phase between NORMAL (0°) and REVERSE (180°).
- Power Switch: Turns the AC power ON and OFF.
- AC Input: Connector for the included power cable.
EVP-X15/18PB Operation Details
Detailed descriptions of the rear panel connectors and controls for the EVP-X15/18PB models:
- INPUT A & INPUT B CONNECTORS: These electronically balanced, XLR and 1/4" phone connectors accept input signal from line-level sources. INPUT A and INPUT B are combined before being routed to the EVP-X15/18PB Low Pass Filter and internal amplifier. INPUT A and INPUT B are also routed to the OUTPUT A and OUTPUT B connectors.
- OUTPUT A & OUTPUT B CONNECTORS: OUTPUT A & B provide either a loop-thru or high-passed, line-level output of the signal from the INPUT A and INPUT B connectors respectively. These connectors work with the OUTPUT A &B switch.
- SPEAKER LEVEL INPUT: This 1/4" phone jack allows connection of the speaker level output of an amplifier or powered mixer to the EVP-X15/18PB internal amplifier.
- VOLUME: This control enables you to adjust the sound volume level. This does not affect OUTPUT A & B.
- OUTPUT A&B SWITCH: This switch affects the signal sent to the OUTPUT A & B connectors.
- THRU: The INPUT A signal is passed directly to the OUTPUT A connector and INPUT B signal is passed directly to the OUTPUT B connector.
- High Pass Filter (HPF): The INPUT A signal is first passed through a 100Hz, 24dB High Pass Filter before being sent to the OUTPUT A connector, whilst the INPUT B signal is first passed through a 100Hz, 24dB High Pass Filter before being sent to the OUTPUT B connector.
- PHASE SWITCH: This switch enables you to select a phase. It is usually set to NORMAL (0°). The REVERSE (180°) setting may improve low-range sounds, depending on the type and location of the entire speaker system. Try both settings and select the one with better sounding low-range output.
- POWER switch: This switch turns the AC power ON and OFF.
- AC input: The power cable that is included with the unit should be inserted here.
System Connection Diagrams
Single EVP-X18PB with Stereo Mid/High Active System
This configuration shows one EVP-X18PB subwoofer used with two EVP-X15P mid/high speakers. Signals from a mixer's line outputs are fed into the INPUT A and INPUT B of the EVP-X18PB. The OUTPUT A & B switch on the EVP-X18PB is set to the HPF position. The high-pass filtered outputs from the EVP-X18PB are then connected to the inputs of the two EVP-X15P speakers.
Stereo Active Sub and Mid/High System
This setup utilizes two EVP-X18PB subwoofers, each paired with an EVP-X15P mid/high speaker. Signals from a mixer's line outputs are fed into the INPUT A and INPUT B of each EVP-X18PB. The OUTPUT A & B switch on both EVP-X18PB units is set to the HPF position. The high-pass filtered outputs from each EVP-X18PB are then connected to the inputs of their respective EVP-X15P speakers.
Stereo Passive Mid/High Speaker with Active Sub System
In this configuration, two EVP-X15 passive mid/high speakers are used with two EVP-X18PB active subwoofers. Left and Right outputs from separate power amplifiers are connected to the EVP-X15 speakers. The EVP-X18PB subwoofers receive their input signals, and their high-pass filtered outputs are routed to the EVP-X15 speakers. The diagram shows the connections for the EVP-X15 (with its own controls like High Frequency Boost/Level) and the EVP-X18PB (with Volume, Input A/B, Output A/B, Phase, Power, AC Input).
EVP-X15P/18PB Block Diagram
The block diagram illustrates the signal flow within the EVP-X15P/18PB. Input signals (A and B) are received and can be routed through a High Pass Filter (HPF) or directly (THRU). The signal then passes through an Equalizer (EQ) and a Low Pass Filter (LPF) before reaching the amplifier section, which is rated at 400W and includes a limiter. The output stage provides outputs A & B, which can be either THRU or HPF. The diagram also shows the Phase switch (0°/180°) and the connection for Speaker Level Input.
Manufacturer Information
Wharfedale International Limited, IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU England.
WHARFEDALE website: www.wharfedalepro.com
IAG Professional reserve the right to alter or improve specifications without notice. All rights reserved © 2004 Wharfedale Pro. A member of the International Audio Group.
