About This Product
The CTSMZ002.2 is an analogue Mazda Steering Wheel Control Interface. It does not support Time/Date Change or Temperature Display.
A photograph shows the Connects2 interface module, a wiring harness with multiple colored wires and connectors, and a 12-way molex connector. Icons indicate Analogue, USB, Plug and Play, Park Brake, Reverse Gear, and Speed Pulse functionality.
Product Contents:
- Interface
- Harness
- Instruction
Prior to Installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure you use the correct tools to avoid damage to the vehicle or product. Connects2 cannot be held responsible for the installation of this product.
Wiring Colour Codes
| Wire Colour | Function | Wire Colour | Function |
|---|---|---|---|
| Yellow | Permanent 12V | Purple | Right Rear Speaker + |
| Black | Ground | Purple/Black | Right Rear Speaker - |
| Red | 12V Ignition | Green | Left Rear Speaker + |
| Orange | Illumination | Green/Black | Left Rear Speaker - |
| Blue/White | Amp Remote | Grey | Right Front Speaker + |
| Pink | Speed Pulse | Grey/Black | Right Front Speaker - |
| Green | Park Brake | White | Left Front Speaker + |
| Purple/White | Reverse | White/Black | Left Front Speaker - |
Technical Support
Connects2 aims to provide a fast and suitable resolution for any technical issues. When contacting Connects2, please provide as much information as possible to speed up the process.
Please use our dedicated online technical support centre: support.connects2.com
Subscribe to our YouTube Channel for installation guides and tips: www.youtube.com/connects2 ▶️
Fitting Guide
Step 1
Remove and disconnect the original head unit.
Step 2
Connect the 12-way molex connector of the head unit patch lead (supplied separately) to the interface.
Step 3
Connect the opposite end of the head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit. This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect.
Important Note: This step must be completed before connecting power to the interface. Failure to do so may result in no steering wheel control function.
Step 4
Connect the 14-way molex connector to the interface.
Step 5
Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For aftermarket head units without an ISO connector, please refer to the wiring colours on Page 2.
Step 6
Connect the female vehicle specific connector to the male vehicle connector. Test head unit for correct operation.
Steering Wheel Control Functions
A close-up photograph of a car's steering wheel controls shows the functions: Source, Track -, Volume -, Mute, Track +, and Volume +.
Application
This interface is compatible with the following Mazda models:
| Mazda Model | Years | Mazda Model | Years |
|---|---|---|---|
| Mazda 2 | 2003> | Mazda CX-7 | 2007> |
| Mazda 3 | 2004> | Mazda Demio | 1998-2003 |
| Mazda 5 | 2005> | Mazda MPV | 1999-2004 |
| Mazda 6 | 2002> | Mazda MX-5 (NB/NC) | 1999> |
| Mazda CX-5 | 2012> | Mazda Premacy | 1999-2004 |
| Mazda B-Series | 1999 - 2006 | Mazda RX-8 | 2003 - 2010 |
| Mazda BT-50 | 2006-2009 | Mazda Tribute | 2001 - 2004 |
| Mazda 626 | 1999 - 2002 |
Connects2
