Panasonic Ventilating Fan Installation Instructions

IMPORTANT SAFETY INFORMATION

To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always observe the following safety precautions.

Symbol Word Panels:

• WARNING: Denotes a potential hazard that could result in serious injury or death.
• CAUTION: Denotes a hazard that could result in minor injury.
• NOTICE: Denotes a hazard that could result in property damage.

Instruction Symbols:

• Symbol 1: Used to alert users to a specific operating procedure that must be followed.
• Symbol 2: Used to alert users to a specific operating procedure that must NOT be performed.
• Symbol 3: Used to alert users not to disassemble the equipment.
• Symbol 4: Used to alert users to make sure of grounding.

WARNING

• Use this unit only as intended by the manufacturer.
• Switch power off at the service panel and lock it before servicing or cleaning.
• Installation and electrical wiring must be done by qualified persons according to all applicable codes and standards.
• Ensure sufficient air for proper combustion and exhausting of gases from fuel-burning equipment.
• Do not damage electrical wiring or other hidden utilities when cutting or drilling.
• Ducted exhaust fans must always be vented outdoors.
• If installed over a tub or shower, it must be marked as appropriate and connected to a GFCI protected branch circuit.
• Do not use non-manufacturer recommended replacement parts (e.g., 3D printed parts).
• This product must be properly grounded.
• Do not use with solid-state speed control devices, as they may cause harmonic distortion and humming.
• Do not install in a ceiling insulated beyond R60.
• Do not disassemble the unit for reconstruction.
• Install the fan at least 1.5 m (5 feet) above the floor.

CAUTION

• Follow all local electrical and safety codes, including the NEC and OSHA, using UL approved wire nuts.
• Ensure electric service supply voltage is AC 120V, 60Hz.
• Use special-purpose or dedicated parts, such as mounting fixtures, if provided.
• Wear gloves to protect hands during installation.
• Do not install where interior room temperature may exceed 104°F (40°C).
• For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
• Do not kink the supply wiring.

NOTICE

• Provide make-up air for proper ventilation.
• Do not connect multiple units in parallel; it may cause malfunction.
• Do not install the fan above or inside a 45-degree angle projected outwards from cooking equipment.
• Do not install the unit where ducts are configured in a way that causes successive or excessive bending, or squeezed ducts close to the adapter.

PLEASE READ PRIOR TO INSTALLING THIS FAN

These fans are designed for continuous ventilation to maintain a healthy environment at low CFM levels 24 hours a day. With the optional Multi-Speed module, fans can run continuously at pre-set lower levels (0-100 CFM for FV-0511VK models, 0-120 CFM for FV-1115VKL3). The installer must pre-set the lower setting during installation.

For spot ventilation, fans can handle intermittent needs. Basic models offer three speeds. With the optional Multi-Speed module, speeds can increase up to 150 CFM (FV-1115VKL3) or 110 CFM (FV-0511VK models) when activated by a switch or optional modules like a condensation sensor (FV-CSVK1), motion sensor (FV-MSVK1), or combined sensor (FV-CMVK3).

A High/Low Delay Timer is included to return the fan to its pre-set continuous ventilation mode. The installer should consult with the homeowner for the desired timer setting (0-60 minutes) during installation.

DESCRIPTION

These products are UL listed under file No. E78414. They utilize a sirocco fan driven by a DC motor with an integral transformer, designed for long life, high dynamic response, wider speed ranges, and energy savings. The grille is a spring-attached, quick-removal type with a built-in damper to prevent backflow. The blower uses a high-capacity sirocco fan for reduced noise. The lighting unit is an energy-saving LED (10 W to 12.5 W) providing illumination similar to a 40 W to 60 W incandescent lamp. The night light function consumes 0.1 W to 1.5 W. The unit is TYPE IC-INHERENTLY PROTECTED.

FCC Note: This equipment complies with Part 15 of the FCC Rules for Class B digital devices. It generates, uses, and can radiate radio frequency energy. If it causes harmful interference, reorient the antenna, increase separation, connect to a different circuit, or consult a dealer/technician. Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

SDoC Responsible Party: Panasonic Corporation of North America, Two Riverfront Plaza, Newark, NJ 07102, 1-866-292-7299.

This device complies with Part 15 of the FCC Rules.

UNPACKING

Unpack the unit carefully and verify all parts against the Supplied Accessories list.

SUPPLIED ACCESSORIES AND DIMENSIONS

For models: FV-0511VKSL3, FV-0511VKL3, FV-1115VKL3

• Parts include: Grille, Warranty sheet & Installation instructions, Flex-Z Fast® bracket (with 4 tapping screws), Self-drilling screw, 4 inch duct reducer (optional).
• Dimensions provided in diagrams show measurements in inches and millimeters for various components like the fan body, duct adapter, and bracket.

For model: FV-0511VKSL3K

• Parts include: Grille, Warranty sheet & Installation instructions, Flex-Z Fast® bracket (with 4 tapping screws), Self-drilling screw, 4 inch duct reducer (optional).
• Dimensions provided in diagrams show measurements in inches and millimeters.

WIRING DIAGRAM

The wiring diagram illustrates connections for AC 120V, 60Hz power supply to the fan, light, and optional switches. It specifies connections for live, neutral, and earth ground wires. A warning is included not to connect the red signal wires to a live power supply, as it can damage the product. An optional switch should be used for signal wires.

FEATURES

• Optimum ventilation performance: Utilizes Smart Flow microchip technology to monitor static pressure and adjust fan RPM for consistent performance despite duct resistance.
• Outstanding Energy Savings: WhisperGreen Select® fans use DC motor technology, achieving 30% - 70% greater energy efficiency than ENERGY STAR® requirements.
• Pick-A-Flow® Feature: Allows selection of airflow speeds (50/80/110 CFM for FV-0511VK models, 110/130/150 CFM for FV-1115VKL3) via a switch on the fan. Fans can run continuously or intermittently.

Pick-A-Flow® Switch Diagram shows the switch and model numbers with corresponding air volumes.

INDICATIONS (Plug 'N PlayTM FUNCTION DEVICES)

Panasonic offers optional Plug 'N Play™ modules for enhanced functionality:

• Multi-Speed module (FV-VS15VK1): Allows continuous low-speed ventilation and boosts to high speed for intermittent needs. It's included with FV-0511VKSL3 and FV-0511VKSL3K models. Users can select airflow (CFM) and time delay settings. Choosing a Pick-A-Flow® setting automatically adjusts the Multi-Speed settings.
• Condensation Sensor module (FV-CSVK1): Turns the fan on or boosts speed when humidity is detected, working with the FV-VS15VK1. It anticipates condensation and expels humid air. Pre-set to run for 20 minutes, it then checks humidity and temperature.
• Motion Sensor module (FV-MSVK1): Turns the fan on or boosts speed when motion is detected, also working with the FV-VS15VK1. It's pre-set to run for 20 minutes and re-checks for movement. The sensor has a detection range of 10 feet (3 m) and a 90° field of view at 77°F (25°C).
• Wi-Fi control module (WP100PBA Swidget®): Enables wireless control via the Swidget iOS or Android app using Wi-Fi. Allows connection, grouping, and balancing of products via Bluetooth 5.0 mesh. Features include boost mode control, light module control, sensor status viewing, air quality monitoring, fault notifications, and energy consumption monitoring. Requires a wireless router and internet connection.
• Motion sensor + Condensation sensor module (FV-CMVK3): Activates the fan based on condensation or motion detection. Offers various configurations for motion control, light operation, and fan operation, including automatic shut-off after set periods.

Plug 'N Play™ Modules Combinations: A table details how combining modules (e.g., FV-MSVK1 + FV-VS15VK1) affects fan operation based on motion and humidity detection, including low speed, boost to high speed, and automatic return to low speed after delay times.

INSTALLATION (Plug 'N PlayTM FUNCTION DEVICES)

1. Remove the corresponding connector cover by squeezing the tabs on the clasp.
2. Plug the module into the main PCB box and fix it to the slot, ensuring the connector clicks into place.

INSTALLATION (CEILING MOUNTING)

1. Disconnect power supply and wear gloves.
2. Remove the adapter plate by pressing the tab and sliding the adapter out. Disconnect plugs and remove the machine screw.
3. Install the Flex-Z Fast® bracket: Align and bend down tabs to fit between joists (16" to 24"). Secure with tapping screws. Extend the bracket to the other joist and secure.
4. Install the circular exhaust duct: Secure conduit or stress relief to the junction box knock-out hole. Connect the duct to the adapter using clamps/ties and seal with mastic or foil tape. Secure the adapter to the bracket with self-drilling screws.
5. Wiring: Refer to the wiring diagram (Page 7). Connect fan wires using approved wire connectors, following electrical codes.
6. Insert fan body: Slide the fan body into the adapter assembly until the hook clicks. Secure the fan body to the adapter with a machine screw (M4X8) and to the bracket with two self-drilling screws. Plug the connector into the receptacle.
7. Sealing: Caulk the gap between the flange and ceiling to prevent air leakage.
8. Install grille: For models FV-0511VKL3, FV-0511VKSL3, FV-1115VKL3, insert mounting springs, connect LED lamp wire, and fix the motion sensor into the grille. Adjust switches as desired. For model FV-0511VKSL3K, follow similar steps, ensuring sensor covers are replaced correctly. Ensure LED lamp and sensor cables are fixed to hooks.

CAUTION: Ensure the LED connector is correctly positioned. Fix cables to hooks before assembling the grille. Wait 8-10 seconds for the fan to start when the switch is ON.

INSTALLATION (WALL MOUNTING)

1. Disconnect power supply and wear gloves.
2. Remove the adapter plate as described for ceiling mounting.
3. Install the Flex-Z Fast® bracket: Align and bend down tabs to fit between studs (16" to 24"). Secure with tapping screws. Extend the bracket to the other stud and secure.
4. Install the circular exhaust duct: Secure conduit to the junction box knock-out hole. Connect the duct to the adapter and seal. Secure the adapter to the bracket with self-drilling screws.
5. Wiring: Complete wiring as per step 4 on page 13.
6. Insert and secure fan body: Slide the fan body into the adapter until it clicks. Secure the fan body to the bracket with self-drilling screws and to the adapter with a machine screw.
7. Finish wall work and install grille: Refer to steps 7 and 8 (p. 14). Ensure the adapter is installed upward.

INSTALLATION (RETROFIT)

1. Disconnect power supply and wear gloves.
2. Remove the existing fan, leaving ductwork and wiring in place.
3. Cut opening: Use the provided template to mark and cut the ceiling or wall opening.
4. Install Flex-Z Fast® bracket: Insert the bracket between joists or studs (16" to 24"), aligning and securing it with tapping screws. Extend to the other joist/stud and secure.
5. Install circular exhaust duct and conduit: Pull down the duct and conduit. Connect the duct to the adapter and seal. Secure conduit and connect wires as per the wiring diagram (Page 13). Install the adapter to the bracket using self-drilling screws.
6. Finish installation: Follow steps 5 through 8 (p. 13 to p. 14) for the remaining installation process.

MAINTENANCE (CLEANING)

WARNING: Disconnect power supply before working on the unit.

CAUTION: Perform routine maintenance annually. Wear gloves. Do not use harsh chemicals. Do not immerse the motor in water. Do not soak resin parts in water over 140°F (60°C). Do not use cleaning sprays, solvents, or water on or near sensors.

1. Remove grille: Pull down one mounting spring, disconnect the wire from the receptacle, then pull down the other spring.
2. Clean grille: Use non-abrasive kitchen detergent and wipe dry. Do not use hot water.
3. Clean fan body: Remove dust and dirt with a vacuum cleaner. Use a damp cloth with kitchen detergent to remove dirt, then wipe dry.
4. Reinstall the grille after cleaning.

PRACTICAL GUIDE TO INSTALLATION

• Ducting: Use the shortest, straightest duct routing possible for best airflow, noise, and energy efficiency. Avoid using ducts smaller than recommended. Insulate ducts to reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve rated airflow.
• Duct Size: A circular 6-inch duct is recommended for optimal performance.
• Sealing: Seal all duct joints and exterior penetrations with caulk or similar material to create an airtight path, minimize heat loss/gain, and reduce condensation potential.
• Insulation: Wrap insulation around ducts and/or the fan to minimize condensation buildup and building heat loss/gain.
• Termination: Use a 4-inch or 6-inch roof jack, wall cap, or soffit vent with a backdraft damper. Ensure a 2-3 ft straight run before any elbows. Mechanically connect duct to termination and seal with mastic or approved foil-faced tape. In attic installations, caulk the box to the drywall.

SPECIFICATIONS

Detailed specifications are provided for base model fans and multi-speed fans, including:

• Model Numbers: FV-0511VKSL3, FV-0511VKL3, FV-0511VKSL3K, FV-1115VKL3.
• Airflow Direction: Exhaust.
• Voltage/Frequency: AC 120V, 60Hz.
• Duct Diameter: 4 inches or 6 inches.
• Air Volume (CFM): Ranges vary by model and speed setting (e.g., 50-110 CFM, 110-150 CFM).
• Noise: Measured in sones, typically less than 0.3 sones.
• Speed: Revolutions per minute (rpm) listed for various airflow settings.
• Power Consumption: Listed in Watts (W) for the fan and lighting/night light.
• Weight: Listed in pounds (lb.).

Performance is based on HVI procedures 915, 916, and 920.

PRODUCT SERVICE

Warning Concerning Removal of Covers: The unit should only be serviced by qualified technicians.

For service or parts, contact Panasonic Call Center at 1-866-292-7299 (USA) or 1-800-669-5165 (Canada).

Contact Information:

• Panasonic Corporation of North America, Two Riverfront Plaza, Newark, NJ 07102, www.panasonic.com
• Panasonic Canada Inc., 5770 Ambler Drive, Mississauga, Ontario L4W 2T3, www.panasonic.ca