boAt Rockerz 268 Wireless Earphone Neckband

Introduction

Thank you for choosing boAt Rockerz 268. This manual guides you through the functionality of the wireless earphone neckband. Understanding Bluetooth and device connection is essential for headset usage. We advise reading this manual thoroughly before use and referring to it for guidance.

Package Contents

• 1 x Rockerz 268
• 1 x USB Type C charging cable
• 2 x Pairs of additional earmuffs (Small & Large)
• 1 x Manual
• 1 x Warranty Card
• 1 x Catalogue

Visual Description: The package includes the boAt Rockerz 268 wireless neckband, a USB Type C charging cable, two extra pairs of silicone earmuffs in different sizes, the user manual, a warranty card, and a catalogue.

Functions

1. Power on: When switched off, press and hold the [Multi-function Button] (MFB) for 3 seconds. A voice prompt confirms powering on. The white LED flashes once.
2. Power off: In powered on state, press and hold the MFB for 5 seconds. A voice prompt confirms powering off. The red LED flashes before the device turns off.
3. Play/Pause: Short press the MFB to play or pause music.
4. Volume Up: Short press the [Volume Up Button] (+) to increase volume. A voice prompt indicates maximum volume.
5. Volume Down: Short press the [Volume Down Button] (-) to decrease volume. A voice prompt indicates minimum volume.
6. Answer/End call: Short press the MFB once to answer or end a call.
7. Reject call: Press and hold the MFB for 2 seconds during an incoming call to reject it.
8. Redial: Double press the MFB to redial the last contacted phone number.
9. Previous Track: Press and hold the [Volume Down Button] (-) for 2 seconds to go back to the previous track or restart the current track.
10. Next Track: Press and hold the [Volume Up Button] (+) for 2 seconds to skip to the next track.
11. Reset Device (Clear Paired List): In pairing mode (white and red LEDs flashing), press and hold both the [Volume Up Button] and [Volume Down Button] simultaneously for 5 seconds. The white LED stays on for 2 seconds, indicating the paired device list has been cleared.
12. Dual Pairing: Connect the earphone to one device. Then, switch off both the earphone and the device's Bluetooth. Connect the earphone to a second device, then switch on the first device's Bluetooth. The earphone should connect to both. If not, manually reconnect the first device to activate dual pairing.
13. BEAST™ Mode: Triple press the MFB to switch to Low Latency mode (BEAST™ Mode), indicated by a sound prompt. Triple press again to turn it off and return to normal mode. This mode is designed for gamers to reduce latency and improve the gaming experience.
14. ENx™ Tech: The ENx™ tech algorithm cancels background noise for clear voice calls. This feature is activated by default on the microphone. It ensures clear voice transmission in various environments like traffic, railway stations, or airports.
15. Voice Assistant: Long press the MFB for 1 second to activate the smart voice assistant.

To Pair with Bluetooth

1. When the device is switched off, press and hold the MFB for 4 seconds to power on and enter pairing mode. A voice prompt will announce pairing mode, and the white and red LEDs will flash alternately.
2. On your media device, enable Bluetooth and search for "Rockerz 268" in the list of available devices.
3. Select "Rockerz 268". If prompted for a passcode, enter "0000" to establish the Bluetooth connection.
4. Upon successful connection, the white LED will flash once every 5 seconds.

Note: The neckband will automatically turn off if no pairing is established within 5 minutes.

Visual Description: A diagram shows a smartphone with Bluetooth enabled, displaying "Rockerz 268" in the device list, ready for connection.

To Charge

Use a USB Type C charging cable to charge the earphone via a laptop or an adapter.

1. Low Battery: When the remaining battery is below 20%, a "Battery Low" prompt will sound every 5 minutes, and the red LED will flash 3 times every few seconds.
2. Charging: A solid red LED indicates the earphone is charging. The earphone should not be turned on while charging.
3. Fully charged: A solid white LED indicates the earphone is fully charged.

Specifications

Safety Cautions

• Do not dismantle or remove the product's battery yourself, as this could cause fire or electrical breakdown. Servicing should only be done by qualified service providers or the manufacturer.
• Clean earphones carefully with only a damp soft cloth. Do not use oily volatile liquids. Keep earphones away from extremely hot or cold substances.
• Damage not caused by manufacturing defects will void the product warranty.
• Do not use earphones when it is unsafe, such as while operating a vehicle, crossing a street, or in any activity requiring full environmental awareness.
• To prevent hearing damage, ensure the music player volume is at an appropriate level when wearing the earphones. Exposure to noise levels at or above 85 dB can gradually lead to hearing loss.

Charging Norms & Precautionary Guidelines:

• Charger/Brick/Adapter: 5V 2A
• Cable/Wire: Standard Cable (35 strands @0.10mm diameter/strand)

Other accessories can be paired if their specifications meet the above norms.