Manuals+

Fisher Type Y693 Gas Blanketing Regulator

Instruction Manual
Form 5342
March 2015

Introduction

The Accu-Pressure™ Type Y693 Gas Blanketing Regulator is a pressure reducing regulator with external registration requiring a downstream control line. It is used for accurate pressure control on pressure blanketing systems. The regulator helps in controlling emissions from the blanketed product and protects against contamination by atmospheric conditions.

WARNING: Failure to follow these instructions or to properly install and maintain this equipment could result in an explosion, fire and/or chemical contamination causing property damage and personal injury or death.

Fisher® regulators must be installed, operated and maintained in accordance with federal, state and local codes, rules and regulations and manufacturer's instructions.

If the regulator vents gas or a leak develops in the system, service to the unit may be required. Failure to correct trouble could result in a hazardous condition.

Installation, operation and maintenance procedures performed by unqualified personnel may result in improper adjustment and unsafe operation. Use qualified personnel when installing, operating and maintaining the Type Y693 regulator.

Scope of the Manual

This instruction manual includes installation, startup, maintenance and parts information for the Type Y693 Gas Blanketing Regulator.

Specifications

The Specifications table lists specifications for the Type Y693 Gas Blanketing Regulator. Specifications for a given regulator as it originally comes from the factory are stamped on the spring case nameplate.

Body Sizes and End Connection Styles

Maximum Allowable Inlet Pressure

Maximum Outlet (Casing) Pressure

Outlet Pressure Ranges

See Table 1

Maximum Operating Outlet Pressure to Avoid Internal Part Damage

Material Temperature Capabilities

Spring Case Connection

Approximate Weights

Table 1. Outlet (Control) Pressure Ranges
OUTLET PRESSURE RANGE COLOR CONTROL SPRING WIRE DIAMETER PART NUMBER
psig bar In. mm
Light diaphragm plate 0.5 to 2.0 in. w.c. 1 to 5 mbar Brown 0.109 2.77 1D892527022
2 to 5 in. w.c. 5 to 12 mbar Red 0.120 3.05 1D892627022
5 to 8 in. w.c. 12 to 20 mbar Black 0.130 3.30 1D892727012
8 to 18 in. w.c. 20 to 45 mbar Gray 0.156 3.96 1D893227032
18 to 32 in. w.c. 45 to 80 mbar Dark Green 0.182 4.62 1D893327032
Heavy diaphragm plate 1 to 2 69 to 138 mbar Dark blue 0.225 5.72 1H975827032
1.5 to 3.3 103 to 228 mbar Orange 0.250 6.35 1H975927032
2 to 5 138 mbar to 0.3 bar Yellow 0.283 7.19 1P615427142
Heavy diaphragm plate with brass closing cap and heavy duty spring adjustor 2 to 5.5 138 mbar to 0.4 bar Green stripe 0.363 9.22 0Y066427022
4 to 10 276 mbar to 0.7 bar Silver 0.406 10.3 1H802427032

The regulator will maintain a positive vessel pressure reducing the possibility of vessel wall collapse. The Type Y693 is available in NPS 1-1/2 and 2 / DN 40 and 50 body sizes.

Installation

WARNING: Personal injury, equipment damage or leakage due to escaping accumulated gas or bursting of pressure-containing parts may result if the gas blanketing regulator is overpressured or is installed where service conditions could exceed the limits given in Specifications or where conditions exceed any ratings of the adjacent piping or piping connections. To avoid such injury or damage, provide pressure-relieving or pressure-limiting devices (as required by Title 49, Part 192, of the U.S. Code of Federal Regulations, by the National Fuel Gas Code Title 54 of the National Fire Codes of the National Fire Protection Association or by other applicable codes) to prevent service conditions from exceeding those limits. A regulator should be inspected immediately for damage after any overpressure condition.

Additionally, physical damage to the gas blanketing regulator could result in personal injury and property damage due to escaping accumulated gas. To avoid such injury and damage, install the gas blanketing regulator in a safe and well ventilated location.

Installation Steps

Key numbers referenced in this section are shown in Figures 3, 4 and 5.

  1. Use qualified personnel when installing, operating and maintaining the regulator. Before installing, inspect the regulator for any shipment damage or foreign material that may have collected during crating and shipment. Make certain the body interior is clean and the pipelines are free of foreign material. Apply pipe compound only to the male pipe threads.
  2. The regulator may be installed in any position as long as the flow through the body is in the direction indicated by the flow arrow attached to the body. Install the regulator as close as possible to the blanketed vessel using a straight run of pipe the same size or larger as the regulator body. Position the body (key 28) and/or diaphragm spring case (key 23) so it will not collect moisture or debris into the screened vent (as shown in Figure 2). If the regulator requires repositioning, refer to the body area maintenance procedures and/or the diaphragm and spring case area maintenance procedures in the Maintenance section to reposition the screened vent for the application. If a block valve is required, install a full flow valve between the regulator and the blanketed vessel.
  3. Attach a downstream pressure control line to the female connection in the lower spring case. The female pressure connection is a 1/2 NPT in the steel or stainless steel lower spring case and a 3/4 NPT for the aluminum lower spring case. Connect the other end of the control line to the vessel. To allow for self-drainage, install the control line at an angle so that any liquid material will drain away from the regulator. See Figures 4 and 5 for the location of the external control line connection.

WARNING: If the regulator vents some gas or a leak develops in the system, it indicates that service is required. Failure to take the regulator out of service immediately may create a hazardous condition. In hazardous or flammable gas service, vented gas may accumulate and cause personal injury, death or property damage due to fire or explosion. Vent a regulator in hazardous gas service to a remote, safe location away from air intakes or any hazardous location. The vent line or stack opening must be protected against condensation or clogging.

A typical installation of the Type Y693 regulator is shown in Figure 2. The diagram illustrates the regulator connected to a vessel/tank with gas blanketing pressure, including block valves and vent valves.

  1. For proper regulator operation, a spring case vent (key 56) is required to allow atmospheric pressure to register on the diaphragm. The spring case vent must be kept open and positioned in such a manner to prevent the spring case from collecting moisture, corrosive chemicals or other foreign material. To allow maximum flexibility in installing the regulator, the vent assembly is supplied separately in a bag. Install the vent assembly in the 3/4 NPT vent tapping and position the vent pointed down as shown in Figure 2. Depending on the orientation of the regulator, the elbow (key 75) supplied with the vent may not be required to position the vent pointed down.
  2. To remotely vent the regulator, remove the vent and install obstruction-free tubing or piping into the 3/4 NPT vent tapping. Provide protection on a remote vent by installing a screened vent cap into the remote end of the vent pipe.
  3. If continuous operation of the system is required during inspection or maintenance, install a parallel regulator with a three-valve bypass around the regulator.

Startup and Adjustment

WARNING: To avoid personal injury, property damage or equipment damage caused by bursting of pressure containing parts or explosion of accumulated gas, never adjust the control spring to produce an outlet pressure higher than the upper limit of the outlet pressure range or that particular spring (see Table 1). If the desired outlet pressure is not within the range of the control spring, install a spring of the proper range according to the Diaphragm and Spring Case Area section of the maintenance procedure.

With installation completed, the regulator can be placed in operation by slowly opening the upstream and downstream block valves, if used, while using gauges to monitor pressure. The regulator takes control when downstream pressure is established.

The regulator has been adjusted at the factory to provide approximately the reduced pressure requested. To ensure the correct pressure setting, always use a pressure gauge to verify the outlet pressure setting. The range of allowable pressure settings is stamped on the spring casing nameplate.

If a pressure setting beyond the stamped range is required, install a spring with the desired range by following the procedures for changing the spring and diaphragm in the Maintenance section. To adjust the pressure setting, perform the following steps (key numbers are referenced in Figures 3, 4 and 5):

  1. Remove the closing cap (key 3, if required).
  2. Turn the adjusting screw (key 2) either clockwise to increase outlet pressure or counterclockwise to decrease outlet pressure. The regulator will go into immediate operation. To ensure correct operation, always use a pressure gauge to monitor the blanket pressure when making adjustments.
  3. Replace the closing cap (key 3, if required).

Shutdown

First, close the nearest upstream shutoff valve and then, close the nearest downstream shutoff valve and the block valve on the control line (refer to Figure 2). Next, open the vent valve between the regulator and the downstream shutoff valve nearest to it. Then, open the upstream vent valve and the vent valve in the control line. All pressure between these shutoff valves is released through the open vent valves, since a gas blanketing regulator remains open in response to the decreasing downstream pressure. If vent valves are not installed, safely bleed off both inlet and outlet pressures, and check that the regulator contains no pressure.

Principle of Operation

The Type Y693 Gas Blanketing Regulator reduces a higher-pressure gas to maintain a positive low pressure of blanket gas over a stored liquid (see Figure 2). Also, when the vessel (or tank) is suddenly cooled, causing vapors to contract, the regulator replaces the volume of contracting vapors with a volume of blanketing gas to prevent the internal vessel pressure from decreasing. In both cases, a positive vessel pressure prevents outside air from entering the vessel and reduces the possibility of atmospheric pressure collapsing the vessel.

Gas blanketing regulators respond to a slight decrease in internal vessel pressure (caused by pump out or atmospheric cooling) by throttling open to increase the flow rate of gas into the vessel. When the vessel's liquid level has been lowered to the desired point and the vapor pressure reestablished, the regulator throttles closed.

When the liquid level drops and vessel pressure decreases below the setting of the control spring, the spring force on the diaphragm opens the disk assembly to supply the required flow of gas to the vessel. When vessel pressure has been satisfied, outlet pressure tends to increase slightly, acting on the diaphragm. When the outlet pressure exceeds the control spring setting, the diaphragm moves to close the disk assembly.

Maintenance

Regulator parts are subject to normal wear and must be inspected and replaced as necessary. The frequency of inspection and replacement of parts depends upon the severity of service conditions or the requirements of local, state and federal regulations. Due to the care Emerson™ takes in meeting all manufacturing requirements (heat treating, dimensional tolerances, etc.), use only replacement parts manufactured or furnished by Fisher®.

WARNING: To avoid personal injury, property damage or equipment damage caused by sudden release of pressure, isolate the regulator from all pressure and cautiously release trapped pressure from the regulator before attempting disassembly.

Body Area Maintenance Procedures

For the Aluminum lower casing version only:

Key numbers are referenced in Figure 4.

This procedure is for gaining access to the disk assembly, orifice and body O-ring. All pressure must be released from the regulator, before these steps can be performed.

  1. Remove the cap screws (key 18) that hold the lower casing assembly (key 9) to the body (key 28). Separate the lower casing from the body.
  2. Inspect and replace the orifice (key 27) if necessary. Lubricate the threads of the replacement orifice with a good grade of pipe thread sealant. Install the orifice with 75 to 100 ft-lbs / 102 to 136 N•m of torque.
  3. Inspect the disk (key 99) for nicks, cuts and other damage. Unscrew the machine screw (key 12) and replace the disk with a new part if necessary. Install the new disk, disk washer and machine screw (keys 99, 98 and 12) and tighten to a torque of 1 to 2 ft-lbs / 1 to 3 N•m.
  4. Inspect the bias spring (key 85) and disk holder (key 25). Unscrew the disk holder (key 25) from the valve stem (key 13) and replace the bias spring with a new part, if necessary. Lubricate the disk holder threads and carefully tighten to 5 to 7 ft-lbs / 7 to 9 N•m.
  5. Inspect the body O-ring (key 16) for damage and/or wear and replace if necessary.
  6. Install the lower casing assembly (key 9) to the body (key 28) with cap screws (key 18). Uniformly tighten the two cap screws to a torque of 45 to 50 ft-lbs / 61 to 68 N-m.

For the Steel or Stainless Steel Lower Casing Version Only:

Key numbers are referenced in Figure 5.

This procedure is for gaining access to the disk assembly, orifice, body gasket and split ring. All pressure must be released from the regulator, before these steps can be performed.

  1. Unscrew the union nut (key 19) from the body (key 28) and remove the lower casing assembly (key 20) and split ring (key 17).
  2. Inspect and replace the orifice (key 27) if necessary. Lubricate the threads of the replacement orifice with a good grade of pipe thread sealant. Install the orifice with 75 to 100 ft-lbs / 102 to 136 N•m of torque.
  3. Inspect the disk (key 99) for nicks, cuts and other damage. Unscrew the machine screw (key 12) and replace the disk with a new part if necessary. Install the new disk, disk washer and machine screw (keys 99, 98 and 12), and hand tighten to a torque of 1 to 2 ft-lbs / 1 to 3 N•m.
  4. Inspect the bias spring (key 85) and disk holder (key 25). Unscrew the disk holder (key 25) from the valve stem (key 13) and replace the bias spring with a new part, if necessary. Lubricate the disk holder threads and carefully tighten to no more than 5 to 7 ft-lbs / 7 to 9 N•m.
  5. If necessary, install a replacement body gasket (key 16) into the body (key 28).
  6. Slide the union nut (key 19) as far as it will go onto the lower casing assembly (key 20). Install both halves of the split ring (key 17) into the slots of the lower casing assembly (key 20) and secure them by sliding the union nut down on the split ring.
  7. Install the lower casing assembly (key 20) with the attached split ring (key 17) and union nut (key 19) to the body (key 28).
  8. Tighten the union nut (key 19) until the lower casing assembly (key 20) is secure on the body (key 28).

Diaphragm and Spring Case Area

This procedure is for gaining access to the spring, diaphragm and lever assembly stem. All pressure must be released from the diaphragm case assembly before these steps can be performed. Key numbers are referenced in Figures 3, 4 and 5.

To Change the Control Spring:

  1. Remove the closing cap (key 3, if required), and turn the adjusting screw (key 2) counterclockwise until all compression is removed from the control spring (key 1).
  2. Remove the adjusting screw (key 2) and upper spring seat (key 4 or 44). Change the control spring to match the desired spring range.
  3. Replace the upper spring seat and install the adjusting screw (key 2).
  4. Install a replacement closing cap gasket (key 35), if necessary, and reinstall the closing cap (key 3, if required).
  5. If the spring range was changed, be sure to change the stamped spring range on the nameplate.

To Disassemble and Reassemble Diaphragm Parts:

For the Aluminum lower casing version only:

Key numbers are referenced in Figures 3 and 4.

  1. Remove the downstream external control line. Remove the closing cap (key 3), and turn the adjusting screw (key 2) counterclockwise to remove the adjusting screw (key 2). Remove the upper spring seat (key 4 or 44) and the control spring (key 1).
  2. Remove the hex nuts (key 22), cap screws (key 21) and spring case (key 23).
  3. Remove the diaphragm assembly (key 5) plus attached parts by tilting them so that the pusher post (key 8) slips off the lever assembly (key 49). To separate the diaphragm (key 5) from the attached parts, unscrew the spring holder cap screw (key 30) from the pusher post (key 8).
  4. Inspect the pusher post and replace if required.
  5. To replace the lever assembly (key 49), remove the machine screws (key 11), cotter pin (key 14) and clevis pin (key 10). To replace the valve stem (key 13), unscrew the cap screws (key 18) from the body (key 28) and remove the lower casing assembly (key 9). Pull the valve stem (key 13) out of the lower casing assembly (key 9).
  6. To inspect the body bushing (key 97), remove the bushing snap ring (key 74) and carefully remove the body bushing from the lower casing assembly (key 9).
  7. During the assembly procedure, use lubricants on parts as indicated in Figure 4 and replace parts as required.
  8. Install the body bushing O-ring (key 64) on the body bushing (key 97). A wiper retaining ring (key 63) is required to hold the wiper (key 66) in place while the bushing is installed into the lower casing assembly (key 9). Ensure that the wiper is properly oriented with the wiper lip pointing inward toward the diaphragm. Install the bushing snap ring (key 74) to hold the body bushing in place.
  9. Apply a moderate coating of lubricant to the valve stem (key 13). Install the stem O-ring (key 15) and the two back-up rings (key 69, one on each side of the O-ring) onto the valve stem (key 13).
  10. Install the valve stem (key 13) from the body side of the bushing, this is to ensure that the O-ring groove does not damage the wiper.
  11. Install the lever assembly (key 49) into the stem (key 13) and insert the clevis pin (key 10) and cotter pin (key 14). Secure the lever assembly (key 49) with the machine screws (key 11). Carefully tighten the machine screws to a torque of 7 to 9 ft-lbs / 9 to 12 N•m.
  12. Install the diaphragm and plate assembly (key 5, pattern side up) on the pusher post. Then install the lower spring seat (key 4).
  13. Lubricate the diaphragm cap screw threads (key 30) and insert the cap screw to secure the diaphragm parts to the pusher post (key 8). Carefully tighten to a torque of 7 to 9 ft-lbs / 9 to 12 N•m.
  14. Install the assembled parts in the lower casing (key 9). Make sure that the lever (key 49) fits in the pusher post (key 8) and that the holes in the diaphragm align with the holes in the lower casing.
  15. Install the spring case (key 23) on the lower casing assembly (key 9) so that the vent assembly (key 56) is correctly oriented, and secure with the cap screws (key 21) and hex nuts (key 22) finger tight only.
  16. Insert the control spring (key 1) into the spring case (key 23), followed by the upper spring seat (key 4 or 44) and the adjusting screw (key 2).
  17. Turn the adjusting screw (key 2) clockwise until there is enough control spring (key 1) force to provide proper slack to the diaphragm (key 5). Using a crisscross pattern, finish tightening the cap screws (key 21) and hex nuts (key 22) to 18 to 21 ft-lbs / 24 to 28 N•m of torque. To adjust the outlet pressure to the desired setting, refer to the Startup and Adjustment section.
  18. Install a replacement closing cap gasket (key 35) if necessary, and then install the closing cap (key 3, if required).
  19. Connect the downstream control line and refer to the Startup section before putting the regulator back in operation.

For the Steel or Stainless Steel Lower Casing Version only:

Key numbers are referenced in Figures 3 and 5.

  1. Remove the downstream external control line. Remove the closing cap (key 3, if required), and turn the adjusting screw (key 2) counterclockwise to remove the adjusting screw (key 2). Remove the upper spring seat (key 4 or 44) and the control spring (key 1).
  2. Remove the hex nuts (key 22), cap screws (key 21) and spring case (key 23).
  3. Remove the diaphragm assembly (key 5) plus attached parts by tilting them so that the pusher post (key 8) slips off the lever assembly (key 9). To separate the diaphragm (key 5) from the attached parts, unscrew the spring holder cap screw (key 30) from the pusher post (key 8).
  4. Inspect the pusher post and replace if required.
  5. Inspect the lower spring seat (key 4), lower diaphragm head (key 6) and the lower diaphragm head gasket (key 7) and replace if necessary.
  6. To replace the lever assembly (key 9), remove the machine screws (key 11). To replace the valve stem (key 13), unscrew the union nut (key 19) from the body (key 28) and remove the lower casing assembly (key 20) and split ring (key 17). Pull the valve stem (key 13) out of the lower casing assembly (key 20).
  7. To inspect the body bushing (key 97), remove the bushing snap ring (key 74) and carefully remove the body bushing from the lower casing assembly (key 20).
  8. During the assembly procedure, use lubricants indicated parts (Figure 5) and replace parts as required.
  9. Install the body bushing O-ring (key 64) on the body bushing (key 97). To install the wiper (key 66), place a small swab of lubricant into the body bushing to hold the wiper in place while the bushing is installed into the lower casing assembly (key 20). Ensure that the wiper is properly oriented with the wiper lip pointing inward toward the diaphragm. Install the bushing snap ring (key 74) to hold the body bushing in place.
  10. Apply a moderate coating of lubricant to the valve stem (key 13). Install the stem O-ring (key 15) and the two back-up rings (key 69, one on each side of the O-ring) onto the valve stem (key 13).
  11. Install the valve stem (key 13) from the body side of the bushing, this is to ensure that the O-ring groove does not damage the wiper.
  12. Install the lever assembly (key 9) into the stem (key 13) and secure the lever assembly (key 9) with the machine screws (key 11). Carefully tighten the machine screws to a torque of 2 to 3 ft-lbs / 3 to 4 N•m.
  13. Always use a new lower diaphragm plate gasket (key 31). Install the parts on the pusher post in the order listed below:
    • Lower diaphragm plate gasket (key 7)
    • Lower diaphragm plate (key 6)
    • Diaphragm and plate assembly (key 5) pattern side up
    • Lower spring seat (key 4)
  14. Lubricate the diaphragm cap screw threads (key 30) and insert the cap screw to secure the diaphragm parts to the pusher post (key 8). Carefully tighten to a torque of 7 to 9 ft-lbs / 9 to 12 N•m.
  15. Install the assembled parts in the lower casing (key 20). Make sure that the lever (key 9) fits in the pusher post (key 8) and that the holes in the diaphragm align with the holes in the lower casing.
  16. Install the spring case (key 23) on the lower casing assembly (key 20) so that the vent assembly (key 56) is correctly oriented, and secure with the cap screws (key 21) and hex nuts (key 22) finger tight only.
  17. Insert the control spring (key 1) into the spring case (key 23), followed by the upper spring seat (key 4 or 44) and adjusting screw (key 2).
  18. Turn the adjusting screw (key 2) clockwise until there is enough control spring (key 1) force to provide proper slack to the diaphragm (key 5). Using a crisscross pattern, finish tightening the cap screws (key 21) and hex nuts (key 22) to 18 to 21 ft-lbs / 24 to 28 N•m of torque. To adjust the outlet pressure to the desired setting, refer to the Startup and Adjustment section.
  19. Install a replacement closing cap gasket (key 35) if necessary, and then install the closing cap (key 3).
  20. Connect the downstream control line and refer to the Startup section before putting the regulator back in operation.

Parts Ordering

When contacting your local Sales Office about this regulator, include the type number and all other pertinent information stamped on the nameplate.

Parts List

In this parts list, parts marked NACE are intended for corrosion-resistant service as detailed in the National Association of Corrosion Engineers (NACE) standard MR0-175-90.

Type Y693 Regulator (Figures 3, 4 and 5)

Aluminum lower casing version (Figures 3 and 4)

Key Description Part Number
1 Control Spring, Plated steel See Table 1
2 Adjusting Screw
0.5 to 32 in. w.c. / 1 to 80 mbar spring 1A5896X0022
1 to 5 psig / 69 mbar to 0.3 bar spring 1L928608012
2 to 5.5 psig / 138 mbar to 0.4 bar spring 1A500528982
4 to 10 psig / 276 mbar to 0.7 bar spring 1A500528982
3 Closing Cap
0.5 to 32 in. w.c. / 1 to 80 mbar spring 1A589544022
1 to 5 psig / 69 mbar to 0.3 bar spring 1A589544022
2 to 5.5 psig / 138 mbar to 0.4 bar spring, Brass 1H798714012
4 to 10 psig / 0.28 to 0.69 bar spring, Brass 1H798714012
4 Lower Control Spring Seat, Plated steel
0.5 to 32 in. w.c. / 1 to 80 mbar spring 14B4240X012
1 to 5 psig / 69 mbar to 0.3 bar spring 14B4240X012
2 to 5.5 psig / 0.14 to 0.38 bar spring (2 required) 1H7974X0012
4 to 10 psig / 0.28 to 0.69 bar spring (2 required) 1H7974X0012
5* Diaphragm Assembly
0.5 to 32 in. w.c. / 1 to 80 mbar springs
Nitrile (NBR) 1N9721X0012
Fluorocarbon (FKM) 1N9721X0022
1 to 10 psig / 69 mbar to 0.7 bar springs
Nitrile (NBR) 1N9722X0012
Fluorocarbon (FKM) 1N9722X0022
6 Lower Diaphragm Plate
Stainless steel 0V003935032
Stainless steel (NACE) 0V0039X0022
7* Diaphragm Plate Gasket, Composition 1A348704022
8 Pusher Post ΟΥ096435072
Stainless steel ΟΥ096435072
9 Lever Assembly
NPS 1-1/2/ DN 40 14B4053X052
NPS 2/DN 50 14B4053X062
Stainless steel (NACE) 1E3409X0052
Stainless steel (NACE) 1E3409X0052
11 Machine Screw, Stainless steel (2 required) 1A866935032
12 Machine Screw, Stainless steel 1A8664X00A2
13 Stem
Stainless steel 24B1765X012
Stainless steel (NACE) 24B1765X012
15* Stem O-ring
Nitrile (NBR) 1P4207X0072
Fluorocarbon (FKM) 1L949306382
Perfluoroelastomer (FFKM) 1P4207X0082
16* Body Gasket
Nitrile (NBR) T12587T0012
Fluorocarbon (FKM) T12587T0022
18 Cap Screw, Plated steel (2 required) 1H974724052
21 Diaphragm Case Cap Screw, Plated steel (12 required) 1B136324052
22 Hex Nut, Zinc-plated steel (12 required) 1A309324122
23 Spring Case, Aluminum AE6180X0012
25* Disk Holder, Stainless steel 24B1952X012
Stainless steel (NACE) 24B1952X022
27 Orifice, Stainless steel, 1/2 in. / 13 mm 1A928835032
NPT
NPS 1-1/2 14B3192X012
NPS 2 14B3192X022
Flanged
CL125 FF NPS 2/DN 50 14B3193X012
CL250 RF NPS 2/DN 50 14B3193X022
WCC Steel NPT NPS 1-1/2 14B3192X032
NPS 2 14B3192X042
Flanged CL150 RF NPS 1-1/2 / DN 40 14B4053X012
NPS 2/DN 50 14B4053X022
28 Body
WCC Steel NPT NPS 1-1/2 14B3194X012
NPS 2 14B3194X022
Flanged CL150 RF NPS 1-1/2 / DN 40 14B3195X012
NPS 2/DN 50 14B3195X022
CL300 RF NPS 1-1/2 / DN 40 14B3195X032
NPS 2/DN 50 14B3195X042
EN PN 16, 25 and 40 RF Flanged NPS 1-1/2 / DN 40 14B3195X092
NPS 2/DN 50 14B3195X102
30 Cap Screw, Plated steel
0.5 to 32 in. w.c. / 1 to 80 mbar spring 1A667824052
1 to 5 psig / 69 mbar to 0.3 bar spring 1B720924052
2 to 5.5 psig / 138 mbar to 0.4 bar spring 1E4539X0012
4 to 10 psig / 276 mbar to 0.7 bar spring 1E4539X0012
35* Closing Cap Gasket, Neoprene (CR) 1N446206992
44 Spring Seat, Aluminum ΟΥ095644012
50 Nameplate
51 Drive Screw
56 Vent Assembly Type Y602-8, Plastic 17A6573X022
63 Wiper Retaining Ring 14B2153X012
64* Bushing O-ring
Nitrile (NBR) 1L142906992
Fluorocarbon (FKM) 1P1676X0032
66* PTFE Wiper 14B1553X012
69* PTFE Back-up ring (2 required) 14B2150X012
72 Reducing Nipple, Plastic 14B3323X012
74 Bushing Snap Ring, Stainless steel 14B1764X012
75 Elbow, Plastic 14B3191X012
79 Pin, Stainless steel 1H972935032
80 Lubricant
85 Bias Spring, Stainless steel 14B2154X012
Stainless steel (NACE) 14B3540X012
93 Hex Nut, Plated steel
2 to 5.5 psig / 138 mbar to 0.4 bar spring 1A352424122
4 to 10 psig / 276 mbar to 0.7 bar spring 1A352424122
97 Body Bushing
Stainless steel 24B1455X012
Stainless steel (NACE) 24B1455X022
98 Disk Washer, Stainless steel 14B1954X012
99* Disk
Nitrile (NBR) 14B1953X032
Fluorocarbon (FKM) 14B1953X022
Perfluoroelastomer (FFKM) 14B1953X052
Stainless steel trim (NACE)
Neoprene (CR) 14B1953X042
Fluorocarbon (FKM) 14B1953X022
Perfluoroelastomer (FFKM) 14B1953X052

Steel and Stainless Steel Lower Casing Version (Figures 3 and 5)

Key Description Part Number
1 Control Spring, Plated steel See Table 1
2 Adjusting Screw
0.5 to 32 in. w.c. / 1 to 80 mbar spring 1A5896X0022
1 to 5 psig / 69 mbar to 0.3 bar spring 1L928608012
2 to 5.5 psig / 0.14 to 0.38 bar spring 1A500528982
4 to 10 psig / 0.28 to 0.69 bar spring 1A500528982
3 Closing Cap
Aluminum 1A589544022
Steel 1J880124092
Stainless Steel 1J8801X0022
NPT
NPS 1-1/2 14B3194X032
NPS 2 14B3194X042
Flanged
CL150 RF NPS 1-1/2 / DN 40 14B3195X052
NPS 2/DN 50 14B3195X062
CL300 RF NPS 1-1/2/ DN 40 14B3195X072
NPS 2/DN 50 14B3195X082
EN PN 16, 25 and 40 RF Flanged NPS 1-1/2 / DN 40 14B3195X092
NPS 2/DN 50 14B3195X102
4 Lower Control Spring Seat, Plated steel
0.5 to 32 in. w.c. / 1 to 80 mbar spring 14B4240X012
1 to 5 psig / 69 mbar to 0.3 bar spring 14B4240X012
2 to 5.5 psig / 0.14 to 0.38 bar spring (2 required) 1H7974X0012
4 to 10 psig / 0.28 to 0.69 bar spring (2 required) 1H7974X0012
5* Diaphragm Assembly
0.5 to 32 in. w.c. / 1 to 80 mbar spring Nitrile (NBR) 1N9721X0012
Fluorocarbon (FKM) 1N9721X0022
1 to 10 psig / 69 mbar to 0.7 bar springs Nitrile (NBR) 1N9722X0012
Fluorocarbon (FKM) 1N9722X0022
6 Lower Diaphragm Plate Stainless steel 0V003935032
Stainless steel (NACE) 0V0039X0022
7* Diaphragm Plate Gasket, Composition 1A348704022
8 Pusher Post Stainless steel (NACE) ΟΥ096435072
9 Lever Assembly Stainless steel (NACE) 1E3409X0052
11 Machine Screw, Stainless steel (2 required) 1A866935032
12 Machine Screw, Stainless steel 1A8664X00A2
13 Stem Stainless steel (NACE) 24B1765X012
15* Stem O-ring Nitrile (NBR) 1P4207X0072
Fluorocarbon (FKM) 1L949306382
Perfluoroelastomer (FFKM) 1P4207X0082
16* Body Gasket, Composition 1A348004032
17 Snap Ring, Steel ΟΥ095828982
19 Union Nut WCC Steel OZ017624092
Stainless Steel WCC Steel (NACE) 0Z0176X0012 OZ017624092
20 Lower Casing Assembly WCC steel 34B1452X012
Stainless steel 34B1452X022
21 Diaphragm Case Cap Screw, Plated steel (12 required) 1B136324052
22 Hex Nut, Zinc-plated steel (12 required) 1A309324122
23 Spring Case WCC steel 34B2157X012
Stainless steel 34B2157X022
25* Disk Holder Stainless steel 24B1952X012
Stainless steel (NACE) 24B1952X022
27 Orifice Stainless Steel, 1/2 in. / 13 mm OL040135032
Stainless steel (NACE), 1/2 in. / 13 mm 0L0401X0012
28 Body WCC Steel NPT NPS 1-1/2 14B3194X012
NPS 2 14B3194X022
Flanged CL150 RF NPS 1-1/2 / DN 40 14B3195X052
NPS 2/DN 50 14B3195X062
CL300 RF NPS 1-1/2/ DN 40 14B3195X072
NPS 2/DN 50 14B3195X082
EN PN 16, 25 and 40 RF Flanged NPS 1-1/2 / DN 40 14B3195X092
NPS 2/DN 50 14B3195X102
WCC Steel (NACE) NPT NPS 1-1/2 14B3194X052
NPS 2 14B3194X062
30 Cap Screw, Plated steel
0.5 to 32 in. w.c. / 1 to 80 mbar springs 1A667824052
1 to 5 psig/69 mbar to 0.3 bar springs 1B720924052
2 to 5.5 psig / 138 mbar to 0.4 bar spring 1E4539X0012
4 to 10 psig / 276 mbar to 0.7 bar spring 1E4539X0012
35* Closing Cap Gasket, Neoprene (CR) 1N446206992
44 Spring Seat, Aluminum ΟΥ095644012
50 Nameplate
51 Drive Screw
56 Vent Assembly Type Y602-8, Plastic 17A6573X022
63 Wiper Retaining Ring 14B2153X012
64* Bushing O-ring Nitrile (NBR) 1L142906992
Fluorocarbon (FKM) 1P1676X0032
66* PTFE Wiper 14B1553X012
69* PTFE Back-up ring (2 required) 14B2150X012
72 Reducing Nipple, Plastic 14B3323X012
74 Bushing Snap Ring, Stainless steel 14B1764X012
75 Elbow, Plastic 14B3191X012
79 Pin, Stainless steel 1H972935032
80 Lubricant
85 Bias Spring, Stainless steel 14B2154X012
Stainless steel (NACE) 14B3540X012
93 Hex Nut, Plated steel
2 to 5.5 psig / 138 mbar to 0.4 bar spring 1A352424122
4 to 10 psig / 276 mbar to 0.7 bar spring 1A352424122
97 Body Bushing Stainless steel 24B1455X012
Stainless steel (NACE) 24B1455X022
98 Disk Washer, Stainless steel 14B1954X012
99* Disk Nitrile (NBR) 14B1953X032
Fluorocarbon (FKM) 14B1953X022
Perfluoroelastomer (FFKM) 14B1953X052
Stainless steel trim (NACE) Neoprene (CR) 14B1953X042
Fluorocarbon (FKM) 14B1953X022
Perfluoroelastomer (FFKM) 14B1953X052

Diagrams

Figure 1 shows a Type Y693 Gas Blanketing Regulator.

Figure 2 illustrates a typical Type Y693 installation, showing the regulator connected to a vessel/tank with gas blanketing pressure, including block valves and vent valves.

Figure 3 displays the Type Y693 Adjusting Screw/Control Spring Combinations with diagrams of different spring case configurations and their corresponding control springs.

Figure 4 shows the Type Y693 Regulator, Aluminum Lower Casing Version, with a detailed diagram and key numbers.

Figure 5 shows the Type Y693 Regulator, Steel or Stainless Steel Lower Casing Version, with a detailed diagram and key numbers.

Contact Information

Industrial Regulators

Emerson Process Management Regulator Technologies, Inc.
USA - Headquarters
McKinney, Texas 75070 USA
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574

Asia-Pacific
Shanghai 201206, China
Tel: +86 21 2892 9000

Europe
Bologna 40013, Italy
Tel: +39 051 419 0611

Middle East and Africa
Dubai, United Arab Emirates
Tel: +971 4811 8100

Natural Gas Technologies

Emerson Process Management Regulator Technologies, Inc.
USA - Headquarters
McKinney, Texas 75070 USA
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574

Asia-Pacific
Singapore 128461, Singapore
Tel: +65 6770 8337

Europe
Bologna 40013, Italy
Tel: +39 051 419 0611
Chartres 28008, France
Tel: +33 2 37 33 47 00

Middle East and Africa
Dubai, United Arab Emirates
Tel: +971 4811 8100

TESCOM

Emerson Process Management Tescom Corporation
USA - Headquarters
Elk River, Minnesota 55330-2445, USA
Tels: +1 763 241 3238
+1 800 447 1250

Europe
Selmsdorf 23923, Germany
Tel: +49 38823 31 287

Asia-Pacific
Shanghai 201206, China
Tel: +86 21 2892 9499

For further information visit www.fisherregulators.com

The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their respective owners. Fisher is a mark owned by Fisher Controls International LLC, a business of Emerson Process Management.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. Emerson reserves the right to modify or improve the designs or specifications of such products at any time without notice.

Emerson Process Management Regulator Technologies, Inc. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson Process Management Regulator Technologies, Inc. product remains solely with the purchaser.

© Emerson Process Management Regulator Technologies, Inc., 1994, 2015; All Rights Reserved

Models: Y693 Gas Blanketing Regulator, Y693, Gas Blanketing Regulator, Blanketing Regulator, Regulator

File Info : application/pdf, 12 Pages, 1.75MB

PDF preview unavailable. Download the PDF instead.

EMERSON FISHER Y693 (01)

References

Related Documents

Preview POSI-SEAL Type A31A Cryogenic High Performance Butterfly Valve Instruction Manual
Comprehensive instruction manual for the POSI-SEAL Type A31A Cryogenic High Performance Butterfly Valve, covering installation, maintenance, parts ordering, and specifications. Includes detailed procedures, safety warnings, and parts lists.
Preview Fisher 299H Series Pressure Reducing Regulators Instruction Manual
Comprehensive instruction manual for Fisher 299H Series pressure reducing regulators, covering installation, adjustment, maintenance, and parts ordering. Designed for broad capacity in distribution, industrial, and commercial applications, these regulators feature integral pilots and handle inlet pressures up to 175 psi.
Preview Fisher Type 114PL High-Pressure Reducing and Low-Flow System: Instruction Manual
Instruction manual for the Fisher Type 114PL High-Pressure Reducing and Low-Flow System. Covers installation, startup, adjustment, maintenance, specifications, operational schematics, safety warnings, and parts ordering. Includes model numbers D104438X012, BSL85, and RPE.
Preview Fisher Type EZR Pilot-Operated Regulator Instruction Manual
Instruction manual for the Fisher Type EZR Pilot-Operated Regulator, covering its description, characteristics, operation, installation, maintenance, and troubleshooting. Includes specifications for various pilot types and regulator options.
Preview Fisher 1261-R and 1261-E Self-Operated Control Valves Instruction Manual
This instruction manual provides comprehensive guidance for the Fisher 1261-R and 1261-E self-operated control valves. It details product descriptions, specifications, installation procedures, maintenance guidelines (including packing and trim), parts ordering, and dimensional data. The manual is essential for proper installation, operation, and maintenance to ensure safety and optimal performance.
Preview Fisher 299H Series Pressure Reducing Regulators Instruction Manual
Comprehensive instruction manual for Fisher 299H Series pressure reducing regulators, covering installation, adjustment, maintenance, specifications, and parts ordering. Includes details on 299H, 299HR, 299HV, and 299HVR models, their operation, and safety warnings for industrial and commercial applications.
Preview Fisher 8560 Eccentric Disc Butterfly Control Valve Instruction Manual
This instruction manual provides detailed information on the installation, maintenance, and parts for the Fisher 8560 Eccentric Disc Butterfly Control Valve, covering sizes NPS 2 through 12.
Preview Fisher FIELDVUE DVC6200 Digital Valve Controller Instruction Manual
Comprehensive instruction manual for the Fisher FIELDVUE DVC6200 Digital Valve Controller, covering installation, configuration, operation, maintenance, troubleshooting, specifications, wiring, calibration, diagnostics, and parts. Developed by Emerson for industrial control applications.