VOVO | Bidet Toilet & Bidet Toilet Seat On-line mall – VOVO-US
User Guide for VOVO models including: TCB 9100GA Integrated Smart Bidet Toilet, TCB 9100GA, Integrated Smart Bidet Toilet, Smart Bidet Toilet, Bidet Toilet, Toilet
Integrated Smart Bidet Toilet TCB-9100WA (Auto) – VOVO USA
File Info : application/pdf, 36 Pages, 6.88MB
DocumentDocumentENGLISH/FRENCH/SPANISH
9100GA 9100WA 9100G 9100W
8200SA 8200S
8200SA (Black) 8200S (Black)
- TCB 9100GA / TCB 9100WA - TCB 9100G / TCB 9100W
Stainless Steel Nozzle
- TCB 8200SA / TCB 8200SA (Black) - TCB 8200S / TCB 8200S (Black)
Stainless Steel Nozzle
Extract bad water before install 1. Direct the supply hose end into a 3 gal (11.4)or larger bucket. 2. Make sure that the supply stop can provide a minimum of
1.0gal(3.7)or more in 10 seconds. 3. Shut off the water supply. Proceed to next step
415 x 700 x 545mm / 16.33 x 27.55 x 21.45 in
390 x 660 x 550mm / 15.35 x 25.98 x 21.65 in
~
)BOEUJHIUPOMZ
Y
TCB 8200SA / TCB 8200SA (Black) TCB 8200S / TCB 8200S (Black)
TCB 8200SA / TCB 8200SA (Black) TCB 8200S / TCB 8200S (Black)
- TCB 9100GA / TCB 9100WA - TCB 8200SA / TCB 8200SA (Black)
- Press Turbo button, Turbo wash will operate. - It starts from the lowest water pressure for
safety reason. - After using the Turbo wash, the posterior and
feminine wash pressure will automatically lowered to 1 level. - When the water pressure is level 1, please raise the water pressure again.
- TCB 9100GA / TCB 9100WA - TCB 8200SA / TCB 8200SA (Black)
- TCB 9100GA / TCB 9100WA - TCB 8200SA / TCB 8200SA (Black)
- TCB 9100G / TCB 9100W - TCB 8200S / TCB 8200S (Black)
- In power saving mode, if left unused for more than 1 hour, both the water temperature and seat temperature are reduced by one level compared to their current settings. - When the product is used again, the temperature will return to the original temperature setting.
- Press Turbo button, Turbo wash will operate. - It starts from the lowest water pressure for
safety reason. - After using the Turbo wash, the posterior and
feminine wash pressure will automatically lowered to 1 level. - When the water pressure is level 1, please raise the water pressure again.
- TCB 9100G / TCB 9100W - TCB 8200S / TCB 8200S (Black)
-En mode économie d'énergie, si vous ne l'utilisez pas pendant plus d'une heure, la température de l'eau et celle du siège seront maintenues à un niveau inférieur d'un cran par rapport aux réglages d'origine pour économiser de l'énergie. -Lorsque vous utiliserez à nouveau le produit, la temperature reviendra à ses paramètres d'origine.
- TCB 9100G / TCB 9100W - TCB 8200S / TCB 8200S (Black)
TCB 9100GA / TCB 9100WA / TCB 8200SA / TCB 8200SA (Black)
- TCB 9100GA / TCB 9100WA / TCB 8200SA / TCB 8200SA (Black)
TCB 9100GA / TCB 9100WA / TCB 8200SA / TCB 8200SA (Black)
TCB 9100G / TCB 9100W / TCB 8200S / TCB 8200S (Black)
TCB 9100GA / TCB 9100WA / TCB 8200SA / TCB 8200SA (Black)
TCB 9100G / TCB 9100W / TCB 8200S / TCB 8200S (Black)
~
Is the bidet power on? (For check the power LED on the body display unit.)
Unplug the power cord, wait for 5 minutes, then plug it back and check the power.
Is the LED on the body display or body control unit flashing?
For if the power+power-save LED on the main unit are flashing together, it indicates a water supply issue. Open the water supply valve fully and perform hard reset. If any other LED is flashing or the issue persists after following the above steps, please email to support@vovousa.com
The Seat is not warm
Have you replaced the remote
Please replace with new batteries
control batteries? Have you inserted and check the polarity. Refer to
them correctly?
page 13.
Is the seat temperature set to low level?
Adjust seat temperature with Seat Temp button on the remote control.
Is it in power saving mode?
When the power-save mode is on, you may need to wait for about 3 to 5 minutes, or you can turn off the power-save mode and use the desired temperature at any time.
The heater automatically switches off
after the user has been seated for 1 hour.
It turns back on when the user stand up.
- This is a safety measure to prevent
low-temperature burns.
The water is cold.
Is the bidet power on? (For check the power LED on the body display unit.)
Is the LED on the body display or body control unit flashing?
Have you replaced the remote control batteries? Have you inserted them correctly?
Unplug the power cord, wait for 5 minutes, then plug it back and check the power.
For if the power+power-save LED on the main unit are flashing together, it indicates a water supply issue. Open the water supply valve fully and perform hard reset. If any other LED is flashing or the issue persists after following the above steps, please email to support@vovousa.com
Please replace with new batteries and check the polarity. Refer to page 13.
Is the water temperature set to low level?
Is it in power saving mode?
Adjust water temperature with Water Temp button on the remote control.
If you find it difficult to wait for the cold water to warm up each time, please turn off the power-save mode, so you can use the warm water immediately.
Posterior / Feminine / TURBO
Water stops
wash will perform for 1 minute and it will stop automatically.
in the middle
of cleansing. Is the human body away from the
seat sensor?
Press the Posterior / Feminine / TURBO wash button again.
Please refer to pages 8-9 to locate the Seat Sensor and ensure that it is detecting the human body.
Is the water supply interrupted?
Wait until the water supply is restored.
Water is not Is the water shutoff valve closed?
spraying out.
Is the human body away from the seat sensor?
Is the hose twisted or bent?
Open the water shutoff valve.
Please refer to pages 8-9 to locate the Seat Sensor and ensure that it is detecting the human body.
Loosen the hose.
Water pressure Is the water pressure set to low
is weak
level?
Adjust the water pressure to higher level using the remote controller.
The water flows When the seat sensor is activated,
into toilet for a it may release some water before
few the
seconds near nozzle when
spraying. If the user change position while seated, the sensor will turn on and
sitting on the off and release some water.
toilet.
This symptom is not a malfunction.
When flushing doesn't work
Is the water shutoff valve fully
When waste open?
doesn't go
down during
Is the supplied water pressure not too weak?
flushing
Please fully open the water shutoff valve.
For smooth flushing, a minimum pressure of 0.15 MPa is required. Please refer the troubleshooting guide on www.vovo-us.com website. If the water pressure still weak please email to support@vovousa.com
Has any large debris (sanitary pads, Use a plunger or call a technician toothbrushes, etc.) been flushed to unclog. into the toilet?
When there is
leakage from Has the upper bidet unit been
the right side of the product
properly attached to the ceramic bowl?
during flushing?
If the upper bidet unit appears to be floating on the ceramic bowl when viewed from the right side, please attach it properly.
Auto
Is the auto flushing turned off?
flushing is (When off, the auto flushing LED not working. on the remote control will be off)
Press the Auto flushing button on the remote control again to turn it on.
Is there a power outage or is the
circuit breaker switched off?
The unit has no power. Is the power LED on the main
body's display panel turned off?
Wait until the power is restored. Or switch on the circuit breaker.
Press and hold the POWER/STOP button on the side control panel of the main body for 3 seconds to turn on the power.
All wash function Is the seat sensor blocked with wet
or deodorant
towel?
function operates
without someone Is the area where the seat sensor is
sitting on the seat. located wet?
Remove the wet towel.
Use a dry cloth to wipe away the water.
The drying air temperature is low.
The air blow stops during operation.
Is the air temperature set to low level?
The drying function will operate for 3 minutes and then stop automatically.
It may stop if the user changes their position while sitting.
The warm air drying function Is the human body away from the is not working seat sensor?
at all.
Adjust the air temperature with Dry Temp button on the remote control. Press Dry again.
Please refer to pages 8-9 to locate the Seat Sensor and ensure that it is detecting the human body.
Please refer to pages 8-9 to locate the Seat Sensor and ensure that it is detecting the human body.
Is the human body away from the seat sensor?
The deodorization function is not
Have you activated the deodorization function using the remote control?
operational.
Please refer to pages 8-9 to locate the Seat Sensor and ensure that it is detecting the human body.
Press the Deodorant button on the remote control to activate the deodorization function. When the deodorization function is activated, it will automatically turn on when the seat sensor detects a human body and will turn off after the seat sensor does not detect a human body for 1 minute.
Have you replaced the remote
Replace with new batteries and
control batteries? Have you inserted check the polarity. Refer to page
them correctly?
13.
Are the battery polarities
reversed?
Remote
Are the transmitter of the remote
control is not working.
and the receiver on the main unit obstructed?
Are the transmitter of the remote
and the receiver on the main unit
contaminated?
Insert the batteries in the correct order.
Remove any obstruction that may be blocking the transmitters and the receiver.
Wipe away any contamination.
Is the human body away from the seat sensor?
Please refer to pages 8-9 to locate the Seat Sensor and ensure that it is detecting the human body.
I can't flush the toilet with remote control.
Have you replaced the remote
Replace with new batteries and
control batteries? Have you inserted check the polarity. Refer to page
them correctly?
13.
Did you press the button consecutively?
This function cannot be used consecutively. Wait for approximately 10 seconds before the next flush.
Are the transmitter of the remote and the receiver on the main unit contaminated?
Wipe away any contamination.
Power Saving
Is the unit unplugged or is there a Plug in the unit or wait for the
power outage?
power to be restored.
Power saving Is the power save mode turned is not working. on?
if the power-save LED on the main body is turned off, press the power save button on the remote controller to turn on the power save mode.
TCB 9100GA / TCB 9100WA
TCB 9100G / TCB 9100W
TCB 8200SA /
TCB 8200S /
TCB 8200SA (Black) TCB 8200S (Black)
support@vovousa.com