OTTO 10" Ring Light Tripod Kit
Model: OTRLGTST
Safety and General Information
Please read all safety instructions before using this product. Improper use of this product may result in damage to this or attached products. To ensure the product works well, please never use the product in the following conditions:
- Moist or underwater condition.
- Do not use chemical solvent on cleaning this product.
- Do not subject the device to liquid or attempt to disassemble the device.
- Do not use this product in an aircraft.
- Do not expose the device to direct sunlight, heat or flame.
[warning] WARNING [warning]
- ONLY CONNECT USB CORD TO POWER SUPPLY WITH 1A MAX.
- HANDLE WITH CARE, DO NOT USE SHARP METAL OBJECTS.
- STORE THE UNIT IN A DRY PLACE WHEN NOT IN USE.
- INDOOR USE ONLY.
Product Specifications
| Model | OTRLGTST |
|---|---|
| Officeworks Product Code | OTRLGTST |
| Light diameter | 10" |
| Light temperature | 3200-6000K |
| Phone holder width | 62-100mm |
| Tripod height | 80-180cm |
| Rated input | 5V [USB] 1A |
| Rated power | 12.5W (Max) |
| Power supply | USB 2.0 cable (included) |
Assembly Instructions
-
Step 1: Prepare the folded tripod stand.
Description: The image shows a folded tripod stand, which is the starting point for assembly.
-
Step 2: Loosen the screw knob anticlockwise.
Description: A hand is shown loosening a screw knob on the tripod stand in an anticlockwise direction.
-
Step 3: Use both hands to pull the stand legs open.
Description: Both hands are used to pull the legs of the tripod stand outwards to open it.
-
Step 4: Adjust the stand legs then tighten the screw knob.
Description: The stand legs are adjusted to the desired position, and then the screw knob is tightened to secure them.
-
Step 5: Loosen the screw knobs on the middle pole and the top pole.
Description: Screw knobs located on the middle and top poles of the tripod are loosened.
-
Step 6: Pull the poles up to the height (max 1.8m) you want and tighten the knobs.
Description: The poles are extended upwards to the desired height, up to a maximum of 1.8 meters, and the knobs are tightened to secure the height.
-
Step 7: Install the tripod ball-head on the tripod and tighten it.
Description: The ball-head is attached to the top of the tripod and tightened securely.
-
Step 8: Install the ring light and the phone holder on the ball-head and tighten it.
Description: The ring light and the phone holder are mounted onto the ball-head and tightened.
-
Step 9: Loosen the ball-head knob to adjust the right light then tighten, assembly completed.
Description: The ball-head knob is loosened to adjust the angle of the ring light, and then retightened. Assembly is now complete.
Function
The height is adjustable; loosen the locking device to adjust it and tighten whenever needed. The LED light has 3 light modes with 10 adjustable brightness levels.
Component Identification:
- 1: Increase brightness [plus-sign]
- 2: Light mode [mode-icon]
- 3: Decrease brightness [minus-sign]
- 4: On/off [power-button]
- 5: Phone holder
- 6: LED light
- 7: Tripod
- 8: Main pole
- 9 & 10: Locking device
- 11: Ball head
Description of diagram: The diagram illustrates the OTTO 10" Ring Light Tripod Kit. It shows the ring light with an attached phone holder, connected via a cable to a control unit. The control unit features buttons labeled 1, 2, 3, and 4 for brightness adjustment and power. The tripod stand is depicted with its main pole, locking devices, and ball head, with corresponding numbers pointing to each component.
Packing Accessories
- 10" LED Ring Light with USB cable x 1
- Phone cradle x 1
- Phone cradle holder x 1
- Connector piece x 1
- Tripod x 1
- Instruction manual x 1
(Smart phone device and power adaptor are not included.)
Product Warranty
Valid for Australian Customers Only
Officeworks Ltd warrants that this product will be free from defects and work as intended for 3 years from the date of purchase by the original customer. If the product has any defects or does not work as specified during the Warranty Period, Officeworks will, at its election and at its expense, repair or replace the product.
This warranty does not apply:
- to cosmetic damage;
- to damage caused by consumables used in connection with the product;
- where the product has not been used in accordance with all provided instructions;
- to damage arising from fair wear and tear;
- where the product has not been subject to reasonable use;
- where the product has been intentionally or negligently damaged; and/or
- if the customer has attempted to repair the product.
To make a claim under this warranty, please return your product with your receipt or proof of purchase to your nearest Officeworks store or contact 1300 633 423.
This warranty is provided in addition to any rights you may be entitled to under the Competition & Consumer Act 2010. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Officeworks Ltd
236-262 EAST BOUNDARY ROAD
EAST BENTLEIGH VIC 3165 AUSTRALIA
MADE IN CHINA
