B-hyve Hose Faucet Timer Quick Start Guide

Box Contents

• Hose Faucet Timer
• Wi-Fi Hub
• Quick Start Guide

Getting Started: Setup Guide

1. 1) Open the B-hyve App

   Log into your B-hyve account and navigate to 'devices' under settings to add the Hose Faucet Timer as a new device. The app will guide you through the remaining setup process.

   For new users, search for "B-hyve" and download the free Android or iOS app. Create an account to begin timer setup.

2. 2) Power Your Wi-Fi Hub

   Hub MAC Address: Write down the 12-digit alphanumeric code found on the back of the hub.

   Plug the hub into an indoor outlet. Ensure it is within range of your B-hyve device and Wi-Fi signal. Avoid placing the hub in areas where the signal must travel through dirt or thick steel barriers.

3. 3) Enter Pairing Mode

   Press the B-hyve button on the hub to enter pairing mode. The hub will flash a blue light every 5 seconds.

4. 4) Power Your Hose Faucet Timer

   Insert two new AA Batteries (sold separately). The timer is now in pairing mode and will flash a blue light every 5 seconds. You will also hear two clicks approximately 6 seconds apart; this is normal and confirms the valve is closed before water is turned on.

   Timer MAC Address: Write down the 12-digit alphanumeric code located on the bottom of the timer.

   Note: If you need to re-pair or perform a factory reset, press the [on/off button] quickly 5 times.

   Battery Replacement: Replace batteries when the timer flashes a red light every 5 seconds, or when the app notifies you. If you remove or change batteries, you will need to reconnect via Bluetooth to set the correct time and date.

5. 5) Install the Timer

   Your timer is now ready to be attached to any standard hose faucet. Do not place the timer in an underground valve box.

6. 6) Turn on Your Water

   The water supply must remain on for the timer to function correctly.

Manual Watering

To activate manual watering, press and hold the [on/off button] for 5 seconds. To stop watering, even during a programmed cycle, press the [on/off button] once.

Specifications

Timer Specifications

Hub Specifications

Compliance Information

FCC Statement: FCC ID: ML6HT25 & ML6-BH1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment into an outlet on a circuit different from the receiver's; Consult the dealer or an experienced radio/TV technician for help.

This device meets the FCC and IC requirements for RF exposure in public or controlled environments. The end user is advised to maintain a distance of 20 cm from the timer and any personnel to ensure compliance with RF exposure regulations.

IC Statement: IC: 3330A-HT25 & 3330A-BH1. This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.

French Compliance Note: Cet appareil a été testé et déclaré conforme aux limites d'exposition pour les appareils numériques de classe B, selon la section 15 de la Règlementation de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet appareil produit, utilise et peut émettre de l'énergie radio fréquence et, si elle n'est pas installée et utilisée conformément aux instructions, peut causer des interférences nuisibles aux communications radio. Cependant, il n'est pas garanti que des interférences ne se produisent pas dans une installation particulière. Si cet appareil cause des interférences gênantes à la réception d'un signal radio ou de télévision, ce qui peut être déterminé en allumant et en éteignant l'appareil, l'utilisateur peut corriger les interférences en suivant une des mesures suivantes : Réorientez ou repositionnez l'antenne de réception. Augmentez la distance entre l'appareil et le récepteur. Branchez l'appareil dans une prise sur un circuit différent du circuit sur lequel le récepteur est branché. Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide. Cet appareil est conforme aux exigences de la FCC et de l'IC concernant l'exposition aux ondes dans un environnement public ou contrôlé. Il est conseillé à l'utilisateur final de maintenir une distance de 20 cm du contrôleur pour assurer la conformité aux réglementations d'exposition RF. Information de conformité pour le Canada Déclaration de l'IC : Cet appareil est conforme à la norme RSS d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit tolérer toutes les interférences, dont les interférences pouvant causer un fonctionnement non désiré. Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.

Spanish Support Note: Consulte el manual del usuario en línea para obtener instrucciones en español.

Need Help?

If you encounter a problem, please use the following resources before returning your B-hyve to the store.

Scan the QR Code [QR Code] for access to a full user manual, videos, and more.

Call us: [Call] 1-800-488-6156

Text us: [Text] 801-797-2319

Or visit us at: Community.Orbitonline.com