GOXTREME GS1 1-Axis Selfie Gimbal

Manuals in your language are available online: FR, IT, ES, PT, PL, SV, NL, EN. Visit: bit.ly/3RKV96L

Disclaimer

Easypix makes no representations or warranties with respect to this manual. To the maximum extent permitted by law, Easypix expressly limits its liability for breach of any warranty that may be implied to the replacement of this manual with another. Easypix reserves the right to revise this publication at any time without incurring an obligation to notify any person of the revision. Easypix is not responsible or liable for misuse of the information contained herein. For suggestions or corrections, please notify Easypix.

All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For safety and compliance, only the manufacturer shall perform repairs to components. Failure to observe this information can result in injury or equipment damage.

Copyright © by Easypix GmbH. All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, without prior written permission from the publisher.

Contact: Easypix GmbH, Em Parkveedel 11, 50733 Köln, Germany, support@easypix.com, www.easypix.com

Retaining Instructions

Read this manual and its safety instructions before using this product. Follow all instructions to avoid fire, explosions, electric shocks, or other hazards that may result in damage to property and/or severe or fatal injuries. The product should only be used by persons who have fully read and understand this manual. Ensure all users have read and follow these warnings and instructions. Keep all safety information for future reference and pass it on to subsequent users. The manufacturer is not liable for material damage or personal injury caused by incorrect handling or non-compliance with safety instructions.

Explanation of Safety Warnings

[!] WARNING: Indicates a hazard with a medium level of risk which, if not avoided, could result in serious injury.

[NOTICE]: Indicates information considered important, but not hazard-related.

Product Introduction

The GOXTREME GS1 gimbal is a high-quality, single-axis motorized gimbal, tripod, and selfie stick with a removable remote control. Its 3-in-1 functionality ensures smooth and stable videos and photos with your smartphone. An action camera can also be attached for selfie shots.

Intended Use

This product is intended for use wherever videos, photos, or selfies are taken and image stability is critical.

Restrictions

[!] WARNING: The product is not suitable for children under 3 years due to choking hazard.

• Contains small parts. Ensure adult supervision for children to prevent swallowing.
• Not suitable for use underwater or in wet conditions. Keep the gimbal dry at all times.
• Avoid exposing the gimbal to extreme temperatures.

Safety Instructions

[!] WARNING: This product is only suitable for its described purpose. The manufacturer is not liable for damage caused by abnormal use.

[!] WARNING: Read this manual carefully before use and ensure the remote control battery is installed correctly.

• Keep the gimbal out of the reach of small children.
• Ensure the gimbal is not obstructed during use to prevent damage to the internal motor mechanism.
• Dispose of waste and residues at the end of the product's service life according to local laws and regulations.
• Do not use the product if it appears damaged in any way.

Operating Environment

• Do not expose the device to abnormally high or low temperatures. Store the device at room temperature in a dry, dust-free location. Never expose the product to high temperatures or direct sunlight.
• Protect the product from falls, shock, and impact.

Description of the Product

The GOXTREME GS1 Gimbal features the following components:

• 1. Power On/Off & Smartphone Insertion: Controls power and allows smartphone insertion at a 90° angle.
• 2. LED Indicator: Shows the status of the gimbal.
• 3. Gimbal Motor: The motorized axis providing stabilization.
• 4. USB Socket: For charging the gimbal.
• 5. Screw Cap: Used for securing the gimbal.
• 6. Selfie Stick Adjustment: Mechanism to extend or retract the selfie stick.
• 7. Remote LED Indicator: Shows the status of the remote control.
• 8. Shutter Button: Used to take photos or start/stop video recording with the remote.
• 9. Tripod: Integrated legs for stable placement.

Diagram Description: The diagram shows a close-up of the smartphone clamp mechanism with numbered indicators for power/insertion, LED, motor, and USB socket. Another diagram shows the main body of the gimbal with the selfie stick adjustment, remote control attachment point, shutter button, and the integrated tripod base.

Using Your Gimbal

The gimbal is designed for various applications, whether at home or on the move. For correct configuration, always place your smartphone into the holder before switching the device on. For best stabilization, center the smartphone in the clamp for optimal balance.

The remote control can be used attached to the handle or detached for remote operation up to 10m, especially when the gimbal is placed on a surface using its integrated tripod.

Step 1: Unfold the Gimbal

• Open the screw cap.
• Unfold the gimbal and then close the screw cap.
• Move the smartphone holder to release it from the lock.

Step 2: Charging the Gimbal

• Charge the gimbal using the provided USB cable.
• Connect one end of the cable to the gimbal's USB port and the other end to a computer or USB charger with an output not exceeding 1,000mA.
• The LED indicator confirms the battery is charging.

[!] WARNING:

• To avoid the risk of electric shock, do not insert the power cord with wet hands.
• In the unlikely event of overheating, smoke, or unpleasant odors, disconnect the unit immediately from the charging cable.
• Never attempt to access or replace the built-in battery.

Step 3: Remote Bluetooth Pairing

The remote control can be slid upwards to detach from the handle and used remotely up to 10m.

• Remove the plastic tab to enable the battery connection.
• Long press the shutter button for 3 seconds to activate the remote.
• The LED will illuminate, and Bluetooth pairing mode will start automatically.
• Search for new Bluetooth devices in your smartphone's Bluetooth settings menu. The remote will appear as "H5".
• The LED will turn off when Bluetooth pairing is complete.

Diagram Description: A diagram shows the remote control with labels for LED and Shutter button, and a smartphone with a Wi-Fi symbol indicating connection.

Step 4: Inserting the Smartphone

Ensure the cradle is unlocked and the smartphone is centered in the holder.

Diagram Description: The diagram illustrates the process of placing a smartphone into the gimbal's clamp, showing the clamp opening and then holding the phone securely.

Step 5: Selfie Stick or Tripod

Extend the selfie stick or set up the integrated tripod.

Diagram Description: Two images show the gimbal: one extended as a selfie stick held by a hand, and another set up as a tripod with a smartphone attached.

Step 6: Switch On the Gimbal

• With the smartphone in position, long-press the power button for 3 seconds to turn on the stabilizer.
• The stabilizer will activate and configure itself.

Diagram Description: A close-up view shows a finger pressing the power button on the gimbal handle.

Step 7: Changing the Orientation

Short-press the power button to change the gimbal's position from horizontal to vertical.

Note: If the position is changed multiple times, the bracket may snap in, and the gimbal will automatically switch off.

Diagram Description: An illustration shows the gimbal rotating 90 degrees from a horizontal to a vertical position, with an indicator for the power button and the angle.

Step 8: Switch Off the Gimbal

Turn off the stabilizer by long-pressing the power button for 3 seconds.

Change the Remote Control Battery

To change the battery, open the remote control using the recess on the side. A new CR1632 battery is required.

Diagram Description: A sequence of 6 steps illustrates how to change the remote control battery. Step 1: Extend selfie stick. Step 2: Slide remote upwards to remove. Step 3: Open top cover. Step 4: Change CR1632 battery. Step 5: Close top cover. Step 6: Slide remote back into position.

[!] WARNING:

• Only use batteries approved for this product's remote control.
• Remove the battery if the remote will not be used for an extended period.

[NOTICE]: Devices containing built-in batteries must be disposed of according to applicable local regulations and not thrown into household garbage to avoid irreversible pollution.

Box Contents

• Gimbal
• USB cable
• Manual EN/DE

Manuals in further languages are available for download at: www.easypix.info/download-manuals/download/gs1/

Technical Specifications

Disposal

Packaging Disposal: For disposal, separate packaging into different types. Cardboard and board must be disposed of as paper, and foil must be recycled.

[Recycling Symbol Description: A symbol indicating separate collection for recycling.]

Multilingual disposal instructions are provided, including French and Italian, detailing separation of packaging materials and local collection guidelines.

[WEEE Symbol Description: A symbol showing a crossed-out wheeled bin, indicating disposal of Waste Electrical and Electronic Equipment and/or Battery by users in private households in the European Union.]

This symbol on the product or packaging indicates it cannot be disposed of as household waste. Dispose of waste equipment and/or battery via the applicable take-back scheme for recycling. For more information, contact your city office, the shop where you purchased the equipment, or your household waste disposal service. Recycling helps conserve natural resources and protects human health and the environment.

Declaration of Conformity

The EC Declaration of Conformity for GS1 Gimbal can be downloaded here: www.easypix.info/download/pdf/doc_gs1.pdf

[Brand Logo: EASYPIX LIFESTYLE ELECTRONICS] [CE Mark Symbol]