GoXtreme GX1 Dual Gimbal

3-Axis Stabilizing Gimbal

• Compatible with action cams with max. size 6.5 x 4.5 x 2.7cm
• Compatible with smartphones with 6.5 - 8.5cm width
• App compatible with iOS 10.0 or higher / Android 5.0 or higher
• Max. carrying weight: 230g
• 4000mAh battery built-in

Important Warnings and Cautions

⚠️ WARNING: Do not turn on the gimbal until your smartphone or action cam is correctly installed and adjusted. Adjusting the position during operation can cause damage.

Please charge the gimbal fully before first use. Use the included action cam adapter for action cams. The gimbal should only be used in temperatures from 0°C to 40°C. Use of the battery in environments above 40°C can lead to fire or explosion. Use of battery below 0°C can lead to serious damage.

⚠️ CAUTION: The gimbal is a high-precision control device; damages may be caused if it is dropped or subjected to external force, potentially leading to malfunction.

• Make sure the rotation of gimbal axes is not blocked by external force when the gimbal is switched on.
• The gimbal is not waterproof or water-resistant. Prevent contact with liquid of any kind. Use a dry cloth for cleaning.
• Protect the gimbal from dust and sand during use.
• Hold the gimbal's handle still when powering up to ensure successful startup.
• Make sure batteries are fully charged before each use.
• For storage over 10 days, discharge the battery to 40%-65% to extend battery life.
• Charge and discharge the battery completely once every 3 months to keep it active.

Charging the Battery

Charging the Gimbal Battery: Connect the charger cable port on the gimbal's handle to a power source such as a power pack (not included), computer, or phone charger. Note: Do not charge the battery immediately after use if the gimbal is hot. Let the battery cool down to near room temperature.

Charging the Phone from the Gimbal (Powerbank): The USB power out port at the back of the gimbal can charge your smartphone/camera while recording. Note: An L-shape charging connector is required when the smartphone is mounted horizontally.

• Do not place the gimbal near flammable materials or surfaces.
• Never leave the battery unattended during charging.
• Check the charger and cable for damage before use. Never use a damaged cable. Do not clean the cable with alcohol or flammable solvents.
• The battery automatically stops charging when full.

Storage and Travel

Storage: Do not leave the gimbal near heat sources or exposed inside a vehicle on hot days. Store in a dry environment, away from temperatures over 40°C. Avoid over-discharge by not leaving the gimbal unused for too long when the battery is completely discharged.

Travel Notice: Discharge the battery power to 5% or lower before carrying the battery on an air flight.

Functions and Components

The GoXtreme GX1 Dual Gimbal features the following components:

• 1. Smartphone Holder: Secures your smartphone.
• 2. Pan Motor: Allows 330° horizontal rotation.
• 3. Battery Level Indicator: Shows battery status (3.1: >66%, 3.2: >33%, 3.3: <33%).
• 4. Joystick: Controls movement UP/DOWN (tilt) and LEFT/RIGHT (pan).
• 5. Bluetooth Light: Indicates Bluetooth connection status (Blue LED: connected, Flashing: trying to connect).
• 6. Operation Mode Indicator Light: Displays current mode (6.1 Pan and Tilt Follow Mode, 6.2 Pan Follow Mode, 6.3 Lock Mode).
• 7. Power / Mode Button: Powers the gimbal on/off (hold 3s) and switches modes (single press). Double press returns the camera to its original position.
• 8. Zoom Control: Controls zoom functionality.
• 9. Holder Adjustment: For adjusting the holder position.
• 10. Roll Motor: Allows 160° vertical rotation.
• 11. Balance Screw: Adjusts weight distribution for balance.
• 12. Adjustable Arm: Pull out or push to balance the smartphone/camera.
• 13. Tilt Motor: Allows 330° horizontal rotation.
• 14. USB Power Out: Port for charging external devices.
• 15. Micro USB Port: Port for charging the gimbal battery.
• 16. Shutter Button: Captures pictures and videos.
• 17. 1/4 Thread Screw: Standard mounting thread.

Mounting the Smartphone

Step 1: Ensure the gimbal is OFF. Slide the phone holder apart and slide the smartphone all the way right until it touches the tilt motor. The gimbal is compatible with smartphones measuring between 6.5 - 8.5cm in width.

Step 2: Adjust the weight distribution so the smartphone is as centered and slightly horizontal as possible, using the adjustable arm (12). Ensure the smartphone is securely placed to avoid falling out.

Step 3: Switch on the gimbal by pressing the power button for 3 seconds. The gimbal will automatically align itself.

Mounting the Action Cam

Step 1: Mount your action cam in the included adapter using the supplied screws. The adapter is compatible with action cams with a maximum dimensions of 6.5 x 4.5 x 2.7cm.

Step 2: Mount the adapter to the gimbal. Ensure the gimbal is OFF. Slide the holder apart and slide the action cam adapter all the way right until it touches the tilt motor.

Step 3: Adjust the weight distribution so the action cam adapter is as centered and slightly horizontal as possible, using the adjustable arm (12).

Step 4: Switch on the gimbal by pressing the power button for 3 seconds. Then, turn the camera forward by sliding the joystick (4) down.

Switching Between Operation Modes

You can manually adjust the smartphone/camera in different modes. The joystick can also control movement.

1. The stabilizer defaults to PAN & TILT FOLLOW MODE when switched on.
2. Single press the Mode button to switch to PAN FOLLOW MODE.
3. Single press the Mode button again to switch to LOCK MODE.
4. Single press once more to return to PAN & TILT FOLLOW MODE.

Mode Descriptions:

• PAN & TILT FOLLOW MODE: The roll axis is locked, and the smartphone follows the handle's movement in tilt and horizontal directions.
• PAN FOLLOW MODE: Roll axis and tilt axis are locked. The smartphone follows the handle's movement in the horizontal direction. The pan axis rotates smoothly with wrist turns.
• LOCK MODE: All three axes are locked, and the smartphone does not follow handle movement.

Switching from Horizontal to Vertical View

There are two ways to achieve vertical shooting mode:

1. Automatic Switching: Within any of the three modes, rotate the gimbal to the left or right by approximately 70°. The gimbal will automatically enter vertical shooting mode.
2. Manual Switching: Ensure the gimbal is switched off. Loosen the adjustment screw (9) on the back of the holder. Rotate the holder into a vertical position. Slide the smartphone into the holder. With the smartphone in place, re-tighten the screw.

App & Bluetooth Connection

Connect via Bluetooth to conveniently start/stop recording or take photos using the shutter button.

1. Power on the gimbal.
2. Activate Bluetooth on your smartphone.
3. Go to your smartphone's Bluetooth settings and connect to the gimbal.

Additional App Functions: The app offers features like Zoom in/out, Face tracking, Object tracking, Motion time lapse, and more.

1. Scan the QR code on the packaging or download the "Gimbal Pro" app from your app store (AppStore or GooglePlay).
2. Install the app on your iOS or Android smartphone.
3. Activate the Bluetooth function on your smartphone and connect it to the gimbal.
4. Open the Gimbal Pro app and follow the on-screen instructions.

Technical Specifications

All product specifications are correct at the time of print and are subject to change without prior notice. Easypix GmbH reserves the right for errors or omissions. For technical help, please visit our support area on www.easypix.eu.

Conformity

We hereby declare that the CE marking has been affixed to this product in accordance with the essential requirements and relevant provisions of the European directives. The EC Declaration of Conformity can be downloaded here: http://www.easypix.info/download/pdf/doc_gx1.pdf

CE

Disposal

Dispose of packaging: For disposal, separate packaging into different types. Cardboard and board must be disposed of as paper and foil must be recycled.

Disposal of Waste Electrical and Electronic Equipment and/or Battery: This symbol on the product or packaging indicates it cannot be disposed of as household waste. You must dispose of your waste equipment and/or battery by handing it over to the applicable take-back scheme for recycling. For more information, contact your city office, the shop where you purchased the equipment, or your household waste disposal service. Recycling helps conserve natural resources and protects human health and the environment.

⚠️ Battery warning:

• Never dismantle, crush, or pierce the battery, or allow it to short-circuit. Do not expose the battery to high temperatures. If the battery leaks or bulges, stop use.
• Always charge using the provided charger. Risk of explosion if the battery is replaced by an incorrect type.
• Keep the battery out of reach of children.
• Batteries may explode if exposed to naked fire. Never dispose of batteries in a fire.
• Dispose of used batteries observing local regulations.
• Before disposing of the device, please remove the battery.

The camera is not suitable for children under 3 years because of choking hazard.

Logos: RoHS, CE, FC, Made in China / Only for EU, EASYPIX LIFESTYLE ELECTRONICS