YEELIGHT

Introduction

Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please contact the customer line.

Specifications

The following tables detail the specifications for the Yeelight GU10 Smart Bulb W1 models.

Model: YLDP004

Model: YLDP004-A

Installation Steps

Install the bulb

Install the bulb and turn on the power.

Diagram Description: The diagram shows a hand screwing a light bulb into a ceiling fixture. An arrow indicates the next step, which is turning on a light switch.

Notes:

1. Make sure that the power is off when installing, removing, or examining the light bulb.
2. Do not use this product in a lamp with a dimmer (e.g., a desk lamp with a round dimmer switch) to avoid damaging the product.
3. Do not use this product in a damp environment.
4. Do not use the light bulb in a narrow and ill-ventilated lamp shade as it may cause weak signals or heat dissipation issues.

⚠️ Caution: Improper installation or use in poorly ventilated shades may lead to signal issues or overheating.

Connect to Yeelight App

This product can be controlled on the Yeelight App and configured to interact with other Yeelight products.

Download App

Search for "Yeelight" in an App store or scan the QR code to download and install the app.

[QR Code for Yeelight App Download]

Using the Yeelight App

Add Device

• Go to the Yeelight App homepage and click "+" in the upper right corner to add your device.
• Proceed with the configuration as instructed on the App.
• Once you've added a device successfully, you can find it in the device list.

Note: Operation procedures may differ due to App updates. Please follow the instructions within the app.

This product can also be controlled via Mi home, Google Home App, and Amazon Alexa. Download and install one of these apps from an app store and configure your device as instructed.

Restore to factory settings

Use the switch to turn the light bulb on and off five times (on for two seconds and off for two seconds). The light bulb will start to change colour or brightness alternately and automatically change to white light with full brightness after five seconds. This indicates that the light bulb has been restored to its factory settings.

Warnings

• Before using this product, please ensure your voltage matches the product's working voltage. Using it with a different voltage may damage the product and cause safety hazards.
• Do not disassemble this product, as the light diodes can cause eye damage.
• The light bulb will heat up during operation. Do not use it in a closed fixture for extended periods. Ensure sufficient ventilation for heat dissipation.
• For indoor use only.
• Disconnect power before installation to prevent the risk of electric shock.
• Use in Dry Locations only.
• For lamps with a significantly higher weight than the lamps they replace, attention should be drawn to the fact that the increased weight may reduce the mechanical stability of certain luminaires and lamp holders and may impair contact making and lamp retention.
• Under normal use, maintain a separation distance of at least 20cm between the antenna and the user's body.

RF Exposure Information

The Maximum Permissible Exposure (MPE) level is calculated based on a distance of d=20cm between the device and the human body. To maintain compliance with RF exposure requirements, a separation distance of 20 cm between the device and the human should be maintained.

Warranty Conditions

A new product purchased from the Alza.cz sales network is guaranteed for 2 years. If repair or other services are needed during the warranty period, contact the product seller directly. You must provide the original proof of purchase with the date of purchase.

The following are considered a conflict with the warranty conditions, for which the claimed warranty may not be recognized:

• Using the product for any purpose other than that for which it is intended, or failing to follow the instructions for maintenance, operation, and service.
• Damage to the product by natural disaster, intervention by an unauthorized person, or mechanical damage due to the buyer's fault (e.g., during transport, cleaning with inappropriate means, etc.).
• Natural wear and aging of consumables or components during use (e.g., batteries, etc.).
• Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
• If anyone has made modifications, alterations to the design, or adaptations to change or extend the product's functions compared to the purchased design, or used non-original components.

EU Declaration of Conformity

Qingdao Yeelink Information Technology Co., Ltd. hereby declares that the radio equipment type YLDP004/YLDP004-A complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.yeelight.com.

CE