Compliance proofs for products: LANCOM Systems GmbH
User Guide for LANCOM Systems models including: 1793VA, VDSL Voip VPN Router, Voip VPN Router, VPN Router, 1793VA, Router
LANCOM 1793VA: LANCOM Systems GmbH
File Info : application/pdf, 1 Pages, 587.89KB
DocumentDocumentHardware Quick Reference LANCOM 1793VA Gigabit Ethernet 10/100/1000 TE / NT NT VDSL / ADSL ETH 4 ETH 3 ETH 2 ETH 1 Analog 2/4 Analog 1/3 Config (Com) ISDN 1 ISDN 2 USB DC 12 V VDSL / ADSL interface Use the supplied DSL cable for the IP-based line to connect the VDSL interface and the provider's telephone socket. For more information, please contact your Internet service provider. Ethernet interfaces Use an Ethernet cable to connect one of the interfaces ETH 1 to ETH 4 to your PC or a LAN switch. Analog interfaces Connect analog terminal devices to the analog interfaces either directly via RJ11, or with the help of the enclosed TAE adapters. Further adapters are optionally available. Configuration interface Use a serial configuration cable to connect the serial interface (COM) to the serial interface of the device you want to use for configuring / monitoring (separately available). ISDN interfaces ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS. ISDN 2: Internal (NT) ISDN bus. A 100-Ohm resistor for line termination is switchable in LCOS. USB interface You can use the USB interface to connect a USB printer or a USB memory stick. Power After connecting the cable to the device, turn the bayonet connector 90° clockwise until it clicks into place. Use only the supplied power adapter. Cloud-ready Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times. Please observe the following when setting up the device i The power plug of the device must be freely accessible. For devices to be operated on the desktop, please attach the adhesive rubber footpads Do not rest any objects on top of the device Keep all ventilation slots on the side of the device clear of obstruction In case of wall mounting, use the drilling template as supplied Rack installation with the optional LANCOM Rack Mount (separately available) Mounting & connecting LANCOM 1793VA Power Off Green, permanently* Red / green blinking Red blinking 1x green inverse blinking* 2x green inverse blinking* 3x green inverse blinking* Device switched off Device operational, resp. device paired / claimed and LANCOM Management Cloud (LMC) accessible Configuration password not set. Without a configuration password, the configuration data in the device is unprotected. Charge or time limit reached Connection to the LMC active, pairing OK, device not claimed Pairing error, resp. LMC activation code not available LMC not accessible, resp. communication error Online Off Green, blinking Green, permanently Red, permanently WAN connection inactive WAN connection is established (e.g. PPP negotiation) WAN connection active WAN connection error DSL Off Interface deactivated Green, permanently DSL connection active Green, flickering DSL data transfer Red, flickering DSL transfer error Red / orange, blinking DSL hardware error Orange, blinking DSL training Orange, permanently DSL sync Green, blinking DSL connecting ISDN 1, 2 Off Interface deactivated Green, permanently D-channel active Green, flickering ISDN data transfer Red, flickering ISDN transfer error Red / orange, blinking ISDN hardware error ETH 1, 2, 3, 4 Off Green, permanently Green, flickering No networking device attached Connection to network device operational, no data traffic Data transmission VoIP Off Green, permanently Red, permanently Red or green, inverse flashing No SIP accounts defined or VCM is off All defined and active SIP accounts (outgoing) were successfully registered Not all defined and active SIP accounts were registered (possibly still in process) Number of currently used lines (connecting or connected) VPN Off Green, permanently Green, flashing VPN connection inactive VPN connection active VPN connecting Reset Reset button Operated e.g. with a paper clip short press: Restart the device long press: Reset the device Analog 1, 2, 3, 4 Off Green, permanently Orange, blinking Green, blinking Interface deactivated Interface activated Incoming call Connection active Hardware Power supply 12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection Power consumption Max. 15 W Environment Temperature range 035 °C; humidity 095 %, non-condensing Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; dimensions 210 x 45 x 140 mm (W x H x D) Number of fans None; fanless design without rotating parts, high MTBF Interfaces WAN: VDSL2 VDSL2 as per ITU G.993.2; profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 35b VDSL Supervectoring as per ITU G.993.2 (Annex Q) VDSL2 vectoring as per ITU G.993.5 (G.Vector) Compatible with VDSL2 and U-R2 from Deutsche Telekom (1TR112) ADSL2+ over ISDN as per ITU G.992.5 Annex B/J with DPBO, ITU G.992.3, and ITU G.992.1 ADSL2+ over POTS as per ITU G.992.5 Annex A/M with DPBO, ITU G.992.3, and ITU.G.992.1 Supports just one virtual connection at a time in ATM (VPI-VCI pair) ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode. Up to 3ports can be operated as additional WAN ports. Ethernet ports can be electrically disabled in the LCOS configuration. USB USB 2.0 hi-speed host port for connecting USB printers (USB print server), serial devices (COM-port server) or USB drives (FAT file system) ISDN 1 / ISDN 2 ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS. According to the settings, connect an ISDN cable either to the NTBA or the ISDN terminal device. ISDN 2: Internal (NT) ISDN bus. Use an ISDN cable to connect the ISDN device to the ISDN interface. Analog 1 / Analog 3 Use the cable of your analog devices to connect them with the analog interfaces. If Analog 2 / Analog 4 necessary use the adapters from the LANCOM Analog Adapter Set. Config (Com) / V.24 Serial configuration interface/COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for optional connection of analog/GPRS modems. Supports internal COM-port server and provides transparent asynchronous serial-data transfer via TCP. WAN protocols VDSL, ADSL, Ethernet ISDN PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without DHCP), RIP-1, RIP-2, VLAN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD Package content Cable Adapters Power adapter 1 DSL cable for an IP-based line, 4.25 m 2 TAE adapters (RJ11 - TAE) External power supply adapter (230 V), 12 V / 2 A DC/S; barrel / bayonet (EU), LANCOM item no. 111303 (not for WW devices) *) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud. This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device`s WEBconfig interface under "Extras > License information". If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request. Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 111764/0622 LED description & technical details