MULTI-Module Firmware Downloads
Welcome to EdgeTX! - EdgeTX
High Performance Open Source Radio Control Link - ExpressLRS
User Manual for Jumper models including: ROC90, ROC90 Gimbals Sensor, Gimbals Sensor, Sensor
Changzhou Smoothies Electronics Co., Ltd. T12MAX Remote control 2ANTI-T12MAX 2ANTIT12MAX t12max
File Info : application/pdf, 21 Pages, 2.43MB
DocumentDocument9: $(+' 4 /1 -./$' B$'*-V( !*-B 0$&./-/()0'
A8 ).*-$('.
).*-$('.
Thank you for purchasing the Jumper T12 radio system. Please read this instruction manual carefully before use to ensure correct and safe use. Due to version upgrades,there have been changes. The information contained in this manual is subject to change without notice.
Many radio control models are equipped with powerful motors and sharp spinning propellers . Please exercise caution when working on models. Ensure power is disconnected from your models and remove propellers when performing maintenance. Do not operate the T12 radio system under the following conditions.
During bad weather or high wind conditions such as rain, hail, snow, storms, or electromagnetic events. During any conditions of limited visibility. In areas where people, property, powerlines, roads, vehicles or animals may be present. lf you are feeling tired or unwell or under the influence of drugs or alcohol. lf the radio or model appears to be damaged or not functioning correctly. In areas of high 2.4ghz interference or in locations where the use of 2.4ghz radios is prohibited . When the battery is too low to function.
EdgeTX is an experimental firmware. No warranty or implied warranty is given as to the quality and reliability of this firmware. The RC model can cause serious injury or even death if not handled properly. If you choose to use EdgeTX firmware, you will be solely responsible for your model. The author of EdgeTX is not responsible for any injury or damage caused by the use of the EdgeTX firmware. Please use it with caution. The EdgeTX firmware can be found here: https://edge-tx.org ExpressLRS firmware at https://www.expresslrs.org Multi-protocol firmware at https://downloads.multi-module.org
Radio System Overview
Trainer Port 2 Positions Switch
USB-C 10W Fast Charging 2 Positions Switch
Adjustable and Foldable Antenna
Standard JR module
Compartment
Battery Tray
S1 Dial 3 Positions Switch 2 Positions Switch Status Indicator Light
Power Button VS-L Gimbal Trim Button
SYS Button
Page Button RTN Button
Foldable Handle
S2 Dial 3 Positions Switch 2 Positions Switch Status Indicator Light
VS-L Gimbal Trim Button Strap Loop Wheel 1.7"LCD Screen
Note: In order to prevent T12 from entering DFU mode during charging and to reduce the probability of firmware loss during charging, T12 is equipped with a separate Boot0 button. To enter DFU mode, shut down the radio, press and hold the Boot0 button, and then connect the USB cable.
T12 is set to MODE2 (the left-hand throttle) out of the factory. The user can change the mode by himself by reversing the gimbals, and then long-press the "sys" key to enter the "RADIO SETUP" page, turn to the bottom to "mode" and select the corresponding mode
Please use two 18650 batteries under the same brand and model (with the same interna resistance) to power the T12. Make sure that the anode and cathode are not reversedwhen inserting the battery, T12 has a built-in USB charging function, You can connect theradio to a USB to charge the battery.Charging indicator: the green light flashes when theradio is not inserted with batteries; the green light is always on when the battery is charging;the green light is off when the charging is complete. Attn: When the battery is installed in the T12 for the first time, please keep the battery voltage consistent to reduce the burden on the voltage balance circuit.
There are two ways to update EdgeTX firmware. 1.Update firmware by EdgeTX companion. (For more details, please refer to T12 Manual) 2.Update firmware via SD card (lf passed over 1version, please use the first method to update) if your device is not in the Windows system, please use the 2nd method. This is a BOOTLOADER function designed by the EdgeTX developer team, efficient and simple. The upgrade requires two steps. Firstly, copy the firmware downloaded from EdgeTX website to the SD card"FIRMWAREp folder. Secondly find the firmware file you just copied in the remote control SD card, long-press the ENT key to upgrade the bootloader (as shown below)
<
;
;
Adjustment instructions for gimbal stick height
1 Remove the gimbal stick ends locking screw. 2Turning the gimbal stick ends clockwise will shorten the gimbal stick length. Turning it counterclockwise will lengthen the gimbal
stick. 3After adjusting the gimbal stick length, hold the gimbal stick end with your hand and tighten the locking screw.
Warning: The gimbal of the radio controller is a precision device. Excessive force when turning the gimbal stick end may cause the gimbal shaft to come off and become damaged. Do not turn the gimbal head before removing the locking screw!
Locking screw Gimbal stick end
We reserve all the right for the final explanation
FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.