SOUNDPEATS Capsule3 Pro Wireless Earbuds
User Guide
Product Overview
The SOUNDPEATS Capsule3 Pro are wireless earbuds featuring Active Noise Cancellation (ANC) and a focus on cost-effectiveness. This guide provides instructions for setup, operation, and troubleshooting.
Getting Started
First Start:
- Open the charging case. The earbuds will automatically power on.
- Tear off the insulating film on the earbuds' charging contacts.
- Place the earbuds back into the charging case.
- Close the charging case lid. The earbuds will enter charging mode.
- Open the charging case lid again. The earbuds will automatically power on and enter pairing mode.
- On your device, turn on Bluetooth and select "SOUNDPEATS Capsule3 Pro" to connect.
Reset:
- Place both earbuds into the charging case.
- Press and hold the button on the charging case for 10 seconds.
- The LED indicator on the charging case will flash white and red, then turn off.
- Close the charging case lid and open it again. The earbuds are activated.
Product Diagram
The product diagram illustrates the earbuds and charging case, showing the placement of earbuds within the case and the charging contacts.
Wearing
Diagrams show how to properly wear the earbuds for optimal fit and sound quality.
Touch Control
| Operation | Action |
|---|---|
| Power On | Automatically open the charging case lid; the earbuds will automatically power on. |
| Power Off | Place the earbuds back into the charging case and close the lid. |
| Play/Pause/Call | Tap the touch button once. |
| Play Next Song | Double-tap the touch button. |
| Play Previous Song | Triple-tap the touch button. |
| Volume Up | Tap the touch button on the right earbud for 1.5 seconds. |
| Volume Down | Tap the touch button on the left earbud for 1.5 seconds. |
| Activate Voice Assistant | Tap the touch button three times. |
| Switch ANC/Transparency Mode | Long press the touch button for 2 seconds. |
| Game Mode | Tap the touch button three times. |
Q&A
Q1: What does the LED indicator on the charging case mean?
The LED indicator on the charging case shows the remaining power:
- 100% - 50%: Green light is on.
- 49% - 10%: Yellow light is on.
- Under 10%: Red light is on.
Note: When charging, the indicator light flashes slowly. When fully charged, the light stays on.
Q2: How to charge the charging case?
- Connect the charging cable to the charging case and an AC adapter (not included).
- Ensure the charging case is properly connected.
Q3: Why are the earbuds sometimes not connecting to the phone when in the charging case?
- Ensure the charging contacts are clean and free of debris.
- Make sure the earbuds are properly seated in the charging case.
- If the issue persists, reset the earbuds as described in the "Reset" section.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC ID
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- (1) this device may not cause interference, and
- (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible de compromettre le fonctionnement.
Note:
Under Industry Canada regulations, this radio transmitter may only be used with an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut être utilisé avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé par Industrie Canada pour l'émetteur afin que l'utilisateur, à l'effet de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, doit choisir de préférence le type d'antenne et de gain de façon que la puissance isotrope rayonnée équivalente (pire) n'excède pas celle qui est nécessaire à l'établissement d'une communication satisfaisante.
Note
The earbuds and charging case are not toys. Keep them away from children and pets. Do not expose the earbuds and charging case to extreme temperatures (below 0°C/32°F or above 45°C/113°F). Do not use the earbuds while a thunderstorm is occurring. Do not disassemble or modify the earbuds or charging case in any way. Do not use the charging case with a damaged cable or plug. Do not immerse the earbuds or charging case in water or any other liquid.
Multilingual Content
This document contains information in multiple languages, including English, German, French, Spanish, Italian, Japanese, and Chinese. The primary language for this document is English.
