Numatic Floor Machine: HFS & HFM Series

Machine Set-up Guide

Follow these steps for machine setup:

1. Attach brush/pad.
2. Connect power cable.
3. Ensure brush/pad is correctly fitted.
4. Attach transport wheels.
5. Adjust handle height.
6. Operate machine.

Cable and Brush Fitting

Cable: Securely connect the power cable.

Brush Fitting:

• Attach the brush.
• Ensure the brush is correctly mounted.
• Check for proper fit.

Transport Wheels: Attach transport wheels for easy movement.

Handle Height Adjustment

Adjust the handle to the desired height for comfortable operation.

Machine Operation

Follow the numbered steps for operating the machine.

HFT1530 Twin Speed

This model features two speed settings:

• Hi: 300 rpm
• Lo: 150 rpm

FMH Face Fitting

Instructions for fitting the decorative faceplate:

1. Align and attach the faceplate components.
2. Secure the faceplate in place.

About the Machine

Rating Label: Contains essential machine information such as voltage, frequency, power, weight, model, and manufacturer details.

WEEE Directive: Floor machines and accessories should be recycled environmentally friendly. Do not dispose of with household waste. Follow European Directive 2002/96/EC.

PPE (Personal Protective Equipment): Required PPE may include:

• Ear Protection ?
• Safety Footwear ?
• Head Protection ⛑️
• Safety Gloves ?
• Dust/Allergen Protection ?
• Eye Protection ?
• Protective Clothing ?
• Hi-Vis Jacket ?

Caution: Wet Floor Sign ⚠️

Note: A risk assessment should determine the appropriate PPE.

Safety Critical Component: Mains Lead H05VV-F 15M x 3 Core x 1.5mm²

Information for Floor Machine

Warnings:

• Exercise care and attention during use.
• Perform regular and preventative maintenance for safe operation.
• Operators must be instructed on correct use.
• Failure to maintain or use correct parts can render the equipment unsafe.
• Always quote Model Number / Serial Number when ordering spare parts.
• Do not use on surfaces with gradients exceeding machine limits.
• Avoid sudden stops or sharp turns on inclines.
• Clean only while descending ramps.
• This machine is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge. Children should be supervised.
• Use only supplied or specified brushes. Other brushes may impair safety.
• Ensure correct assembly and operation according to safety regulations.
• Take all necessary precautions for operator and bystander safety.
• Wear non-slip footwear when scrubbing. Use a respiratory mask in dusty environments.
• Switch off power before cleaning, servicing, or maintenance. Disconnect mains-powered machines by removing the plug; disconnect battery-powered machines using the ON/OFF button.
• Secure unattended machines against unintentional movement.
• Read detergent/liquid manufacturer's instructions.
• Do not allow the supply cord to contact rotating brushes or pads.

Caution:

• Not suitable for picking up hazardous dust.
• Store indoors only.
• For indoor use only.

Notes: Intended for commercial use (hotels, schools, hospitals, factories, shops, rental businesses). Meets IEC 60335-2-67 requirements.

DO:

• Ensure competent persons unpack/assemble.
• Keep machine clean.
• Keep brushes in good condition.
• Replace worn/damaged parts immediately.
• Regularly examine power cord for damage. If damaged, have it replaced by manufacturer, service agent, or qualified person.
• Replace power cord only with correct Numatic approved parts.
• Ensure work area is clear of obstructions and people.
• Ensure work area is well-lit.
• Pre-sweep the area to be cleaned.

DON'T:

• Use steam cleaners or pressure washers. Do not use in rain.
• Perform maintenance or cleaning with the power plug connected.
• Allow inexperienced persons to perform repairs. Call experts.
• Strain or pull cable to disconnect.
• Leave brush pad on machine when not in use.
• Allow inexperienced/unauthorized operators without training to use the machine.
• Expect trouble-free operation without correct maintenance.
• Run machine over power cable during operation.
• Lift or pull machine by operating triggers; use main handle.
• Remove handle except for service/repair.

Specifications

The document includes detailed specifications for various Numatic floor machine models (HFS, HFM, HFT, FMH) in multiple languages, including EN, DE, FR, NL, PT, IT, ES, PL, SV, FI, DA. The specifications cover:

• Motor power (W)
• Speed (rpm)
• Brush size (mm)
• Pad size (mm)
• Working range (m)
• Weight (kg)
• Sound pressure level (dB(A))
• Hand-Arm Vibration (m/s²)
• Dimensions (mm)

A table presents these specifications across different models, allowing for comparison.

UKCA Declaration of Conformity

This section confirms that Numatic International Limited declares, under its sole responsibility, that the specified products (HFM, HFS, HFT, FMH Single Disc - Floor Treatment - Commercial) conform to relevant UK and EU directives and standards, including Machinery Directive, EMC Directive, and RoHS Directive. It lists the relevant standards and regulations.