Laresar Evol 3 Robot Vacuum Cleaner

Table of Contents

• 1. Safety Instructions
• 2. Package List
• 3. Basic Parameters
• 4. Product Introduction
• 5. Preparation
• 6. Usage Instructions
• 7. Routine Maintenance
• 8. Common Problems
• 9. Troubleshooting

1. Safety Instructions

Usage Restrictions

• This device is for indoor home cleaning only. Do not use outdoors (e.g., on an open balcony), in non-floor-level areas (e.g., on a sofa), or in commercial/industrial environments.
• Do not use the device in areas without protective barriers, such as duplexes, open balconies, or on top of furniture.
• Do not use the product in environments with temperatures above 40°C or below 0°C, or where liquids or viscous substances are present on the floor.
• Secure the grounding cable at home before use to prevent it from being pulled during operation.
• Do not place fragile items (e.g., vases, plastic bags) on the floor, as this may cause the machine to get blocked or lead to damage from minor impacts.
• Keep the machine away from individuals (including children) with physical, mental, or sensory impairments.
• Do not allow children to use the device as a toy. Keep children and pets away from the machine when it is in operation.
• Store the cleaning brush in a location inaccessible to children.
• Do not place objects (including children and pets) on the stationary or moving machine.
• When the device is in operation, keep hair, pet fur, and fingers away from the suction port.
• Do not use the device to clean burning items, such as extinguished cigarette butts.
• Do not use the machine to clean long-haired carpets. Some dark carpets may not be cleaned normally.
• Do not use the device to vacuum hard or sharp objects, such as decorative debris, glass, or iron nails.
• Clean or maintain the device and docking station only when the device is powered off or the power supply is interrupted.
• Do not wipe the device with a damp cloth or liquid.
• Do not use the mopping function on carpets or furniture tops.
• Please follow the instructions in this manual when using the device. The user is responsible for damages and injuries caused by improper use.

Battery and Charging

• Do not use third-party batteries, docking stations, or chargers.
• Do not disassemble, repair, or modify the battery or docking station without authorization.
• Do not place the docking station near heat sources like radiators.
• Do not use a damp cloth or wet hands to wipe or clean the docking station's splitter.
• Dispose of used batteries properly by returning them to professional recycling companies.
• If the power cord is damaged or broken, do not use it and purchase a new one from authorized dealers.
• For transportation, ensure the device is powered on. It is recommended to use the original packaging.
• If the device will not be used for an extended period, turn it off and store it in a dry, cool place.
• Charge the device at least every 3 months to prevent battery damage from over-discharge.
• Only use the detachable power adapter supplied with this device to charge the battery.

Correct Disposal of this Product

This marking indicates that the product should not be disposed of with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your old device, please use the return and collection systems or contact the retailer where the product was purchased. They can ensure the product is recycled in an environmentally sound manner.

2. Package List

The package includes the following items:

• Robot Vacuum Cleaner
• Charging Station
• Water Tank
• Dust Bin
• Wipe Holder
• Mop
• Spare HEPA Filter and Sponge
• Power Adapter (for Charging Station)
• Remote Control
• Magnetic Strip
• Side Brush
• Cleaning Brush

3. Basic Parameters

PS: Rated power symbol reference is shown in the image above.

4. Product Introduction

Robot Components

Clean/Power Button: Short press to start or pause cleaning. Press and hold for 3 seconds to turn the device on or off.

Indicator Light: Blue light: Normal. Red light: Error. Blinking blue light: Connecting to network. Blinking violet light: Searching for robot.

Remote Control

• Automatic Cleaning
• Direction Buttons
• Spot Cleaning
• Mop Water Control: High/Medium/Low
• Home Button: Short press to return to charging station/pause.
• Reset Button: Press with a needle to reset the device.

Suction Height: Note: Set to High, the robot says "3Di". Medium, the robot says "2Di". Low, the robot says "1Di".

Sensor and Structure

Top View Components:

• 1. Top Cover
• 2. Button
• 3. Bumper
• 4. Infrared Anti-collision Sensor
• 5. Infrared Light Receiving Sensor

Bottom View Components:

• 1. Cliff Sensor
• 2. Charging Contacts
• 3. Universal Wheel
• 4. Wheels
• 5. Side Brush
• 6. Roller Brush
• 7. Battery Cover
• 8. Mop Holder Mounting Port

5. Preparation

Precautions

• Before operating the vacuum cleaner, remove cables and items scattered on the floor, and clear away easily falling, fragile, valuable, and potentially dangerous objects. Avoid the robot getting trapped, entangled, dragged, or knocked over, as this could lead to personal injury or property damage.
• Do not use the robot to vacuum liquids, as this will damage the fan and affect the robot's performance.
• If used in a hanging situation, it must be protected by rails to prevent accidental falling or pushing of other objects before falling.

Installation Steps

1. Remove protective material from both sides of the robot.
2. Install Side Brushes: Attach the left brush (L) and right brush (R) to the corresponding L and R markings on the underside; press down to complete installation.
3. Connect the power cable, ensuring it is of an appropriate length.
4. Place the charging station on a flat surface against a wall and connect it to the power outlet.

Note on Charging Station Placement:

• Maintain a clearance of more than 0.5m on the left and right sides, and 1.5m in front of the charging station.
• A power line running vertically to the floor can be dragged by the robot, leading to a power outage at the dock.
• The charging indicator light will illuminate when the battery is charging.

Do not move the charging station arbitrarily; avoid direct sunlight on the station, as it can interfere with charging return signals.

6. Usage Instructions

Powering On and Off

• Tap and hold the button for 3 seconds to turn the device on. The indicator light will illuminate, and the robot vacuum cleaner will enter standby mode.
• When the robot is in standby mode, tap and hold the button for 3 seconds. The indicator light will turn off, and the robot will shut down.
• Note: The robot cannot be turned on while charging.

Cleaning/Pause

• Once the device is powered on, tap the button (on the robot) or use the remote control or smart app to start cleaning.
• Note: The machine cannot clean liquids.
• If the battery level is below 15%, the device cannot operate. Charge the device before cleaning.
• If the battery level drops below 15% during cleaning, the device will automatically return to the docking station to charge.
• Before cleaning, tidy up all cables on the floor (including the charging station's power cable). Otherwise, the machine may pull on the wires during cleaning, potentially causing power outages for other electrical devices or damage to items or cables.

Charging

• Automatic Mode: After cleaning, the robot automatically returns to the charging station.
• Manual Mode: While paused, press the button to activate the "Return to Charge" mode, or use the controller or smart app to charge.

Virtual Wall

The magnetic strip can be used to create barriers for specific areas (e.g., bathrooms, kitchens).

Note: Secure the magnetic strip to the floor to prevent it from detaching, as this could affect the virtual wall's effectiveness.

Cleaning Modes

• Automatic Cleaning: Upon activation, the machine plans its cleaning route in a zigzag pattern, covering the entire room systematically and efficiently. After cleaning, it automatically returns to the docking station (default cleaning mode).
• Spot Cleaning: Use the button on the controller to make the machine focus on its current position, cleaning a circular area with a 1.2m diameter. After cleaning, the robot automatically returns to its starting point and stops. (The direction buttons on the smart app can also be used to manually guide the machine to the cleaning position).
• Edge Cleaning: When cleaning indoors, the device typically follows along a solid object (e.g., a wall). Once cleaning is completed on all sides, the device returns to the charging station. Press the [edge cleaning button] on the controller or use the smart app to quickly activate the edge cleaning function.

DND Mode

No voice prompts are given in DND (Do Not Disturb) mode. Use the smart app to activate or deactivate DND mode.

Suction Control

Use the smart app to select suction modes: "Strong," "Normal," and "Quiet" (default is "Normal").

Water Volume Control

Use the smart app to select water volume modes: "High," "Medium," and "Low" (default is "Medium").

Scheduled Cleaning

Use the smart app to set cleaning times. The robot will automatically start vacuuming at the scheduled time.

• Cleaning begins automatically at the scheduled time.
• After cleaning, the robot returns to the docking station. (7x24h scheduling is supported).

7. Routine Maintenance

Roller Brush (Recommended Cleaning Frequency: Weekly)

1. Turn the device over, press the buckle on the roller brush cover, and remove the roller brush cover. Remove the roller brush.
2. Use the provided cleaning brush to remove dust from the main brush and the roller brush cavity, then remove any entangled items.

Side Brushes (Recommended Cleaning Frequency: Weekly)

1. Turn the machine upside down and pull the side brushes out vertically.
2. Remove any tangled hair and dirt, then reinsert the side brushes.
3. Align the left side brush (L) and right side brush (R) with the L and R markings on the bottom cover and press the side brushes to reinstall them.

Note: It is recommended to replace the side brushes every 3 months to ensure cleaning effectiveness.

Dust Bin and Filter (Recommended Cleaning Frequency: After Each Cleaning)

1. Remove the machine cover, lift the dust bin handle, and take out the dust bin.
2. Press the dust bin switch, open the dust bin, and empty it.

Cleaning the Dust Bin

1. After extended use, remove the filter and the HEPA filter.
2. Wash the removed filter and dust bin under a faucet (the HEPA filter cannot be washed with water).
3. Remove water droplets and thoroughly dry the filter and dust bin before use.

Components: Dust bin, opening switch, filter cover, pre-filter, sponge, HEPA filter.

Notes:

• Use clean water for washing; do not add detergent.
• Do not use a brush or pliers to clean the filter.
• Thoroughly dry the filters for at least 24 hours.
• It is recommended to replace a set of filters every 3 months.

Sensor Cleaning

• Infrared Anti-collision Sensor: Clean monthly.
• Cliff Sensor: Clean monthly.
• Charging Contacts: Clean as needed.
• Signal Transmission Zone: Clean monthly.

Firmware Upgrade

Launch the smartphone app and navigate to the firmware update section. Once new firmware is detected, follow the on-screen instructions. The device must have at least 50% battery power for the upgrade. It is recommended to place the device on the docking station for the upgrade.

8. Common Problems

9. Troubleshooting

Declaration of Conformity

We (the EU-based importer is responsible for this declaration)

Prolinx GmbH (Company Name)

declare under our sole responsibility that the product:

Trade Name: Laresar
Equipment: Robot Vacuum Cleaner
Model No.: SG50R

to which this declaration relates, complies with the essential requirements of the Council Directive on the approximation of the laws of the Member States relating to the RED Directive (2014/53/EU) & RoHS (2011/65/EU). For the product to which CE marking is affixed, the following standards have been applied:

• EN 62368-1:2014+A11:2017
• EN 55014-1:2017+A11:2020
• EN 55014-2:2015
• EN 61000-3-2:2014
• EN 61000-3-3:2013/A1:2019
• EN IEC 62311:2020
• ETSI EN 301 489-1 V2.2.3(2019-11)
• ETSI EN 301 489-17 V3.2.4(2020-09)
• EN 55032:2015/A11:2020
• EN 55035:2017/A11:2020
• ETSI EN 300 328 V2.2.2(2019-07)
• IEC62321-3-1:2013
• IEC62321-4:2013
• IEC62321-5:2013
• IEC62321-6:2015
• IEC62321-7-1:2015
• IEC62321-7-2:2017
• IEC62321-8:2017

Full Name: George.wang
Signature: George.wang
Position: Approbation Manager
Place/Date: Shenzhen, China / Sep.09-2022