Silonn Ice Maker Instruction Manual

Contents

• Important Safety Information
• Product Introduction
• Control Panel Introduction
• Using Your Ice Maker
• Cleaning and Maintenance
• Product Specifications
• Troubleshooting
• Short and Long-Term Warranty Information

Important Safety Information

WARNING: To reduce the risk of injury or property damage, please follow these safety precautions.

• Voltage power from outlet must match specifications on appliance nameplate.
• This appliance must be grounded.
• Using an extension cord may cause overheating and increase the risk of fire. If an extension cord MUST be used: 1) Only use an extension cord with grounding plug. 2) The marked rating of an extension cord must be equal to or greater than the rating of this appliance.
• Do not operate if any component, including the cord or plug, is damaged.
• Unplug the unit before cleaning by hand.
• Only responsible and capable adults should operate the ice maker.
• Do not place the power cord where it could be pulled by children or pose a tripping hazard.
• Children should not be left unattended near the ice maker during operation.
• Do not use water that is micro-biologically unsafe or of unknown quality.
• Do not remove any safety, warning, or product information labels from the unit.
• Do not touch the evaporator with your hands while the ice maker is operating.
• Do not plug in or unplug the unit with wet hands.
• The unit must be placed and set up according to installation instructions before use. The unit is for indoor household use only.
• Do not store or use flammable vapors or liquids near the unit.
• Do not immerse any part of the unit in water.
• Do not attempt to disassemble, repair, modify or replace any part of the ice maker without permission from Silonn or its affiliates.

WARNING: FIRE OR EXPLOSION HAZARD Flammable Refrigerant. This unit contains an isobutane refrigerant, also known as R600a, a natural gas with high environmental compatibility. However, it is also combustible. Adhere to the warnings below to reduce the risk of injury or properly damage.

1. When handling, installing, and operating the unit, care should be taken to avoid damage to the refrigerant tubing.
2. Only dispose of the unit according to Federal and Local Regulations. Contact your local authorities for the environmentally safe disposal of the unit.
3. Keep ventilation openings around the unit's enclosure clear of obstruction.
4. Do not place the unit near heat sources such as an oven.
5. Ensure a minimum of three inches of clearance around the side and back walls of the unit for proper air circulation.
6. Do not place the unit in direct sunlight.

Product Introduction

The Silonn Ice Maker is designed for efficient and convenient ice production. Key components include:

• 1. Large Viewing Window: Allows you to monitor ice production.
• 2. Ice Full Sensor: Detects when the ice basket is full.
• 3. Ice Shovel: Used to scoop ice from the basket.
• 4. Maximum Water Fill Line: Indicates the maximum water level.
• 5. Air Exhaust Fan: Helps dissipate heat.
• 6. Control Panel: For operating the ice maker.
• 7. Handle: For carrying the unit.
• 8. Drain Plug: For draining water.
• 9. Ice Basket: Holds the produced ice.
• 10. Ice Scoop: For serving ice.

Control Panel Introduction

Using Your Ice Maker

Before First Use:

1. Stand the unit upright for 24 hours before use.
2. Check for accessories. Contact customer service if parts are missing.
3. Discard the first 4 cycles of ice. Note: If not used for a long period, discard the first 4 cycles of ice.
4. Use in locations with ambient temperatures between 10°C and 32°C (50°F - 90°F).
5. Installing The Handle: Position the handle over the insert hole, fit it into the insert notch, and lift back to lock into place.

What Not To Do:

• Do not place on an unstable base. ❌
• Do not use other liquids besides drinking water. ❌
• Do not use in high or low temperatures (lower than 41°F/5°C). ❌

How to Use Your Ice Maker:

1. Open the cover and remove the ice basket.
2. Pour water, ensuring it does not exceed the "MAX" water mark.
3. Press the “ON/OFF” button.
4. Press "SELECT" to choose the ice cube size (Large or Small). Wait 6-13 minutes for ice production, depending on room temperature and ice size.
5. The ice maker is ready when the "ICE FULL" indicator is on.
6. When the "ADD WATER" indicator is red, refill water and press “ON/OFF”.

Cleaning and Maintenance

It is recommended to clean the unit once per week.

Manual Cleaning:

1. Remove the ice basket.
2. Clean the interior using a soft cloth with warm water and vinegar, then rinse with clean water.
3. Drain excess water over a sink using the drain plug.
4. Clean the exterior with a cloth and mild dish-washing soap.

Self-Cleaning (30-Minute Process):

1. Remove the ice basket and add water.
2. In Standby Mode, hold the “ON/OFF/CLEAN” button for 5 seconds to start self-cleaning.
3. Drain excess water over a sink using the drain plug.
4. Clean the exterior with a cloth and mild dish-washing soap.

DO's & DON'Ts while cleaning and maintaining:

• Do not use organic solvent, boiled water, detergent, strong acid, and strong alkali etc. for cleaning.
• When the unit is not to be used for a long duration, drain the water completely & dry the interior.
• Store in a well-ventilated area.

Product Specifications

Troubleshooting

Short and Long-Term Warranty Information

30-Day Limited Warranty

To provide customers with a quality shopping and user experience, the unit can be replaced or returned for a full refund within the 30-day period from the date of purchase.

30-Day to 1-Year Limited Warranty

After the 30-day warranty has expired, Silonn automatically activates a 1-year warranty from the date of purchase that covers product replacement. Please note that proof of purchase is required for all warranty claims.

30-Day to 1-Year Warranty Limitations

This warranty does not cover:

• Any condition resulting from incorrect or inadequate maintenance or care.
• Damage resulting from misuse, abuse, negligence, accidents, or shipping damage.
• Dissatisfaction due to buyer's remorse.
• Normal wear and tear.
• Damages incurred after initial transportation.