INSTAR IN-8815 4K Indoor Camera - User Manual

This document provides a comprehensive guide to the INSTAR IN-8815 4K Indoor Camera. It covers features, installation, operation, and technical details.

1. Camera Introduction

The IN-8815 4K is a high-resolution, controllable indoor camera featuring an integrated PIR motion sensor, eight configurable software-based alarm areas, and intelligent object detection. It can distinguish between people, vehicles, and animals to minimize false alerts. The camera boasts a high-performance Sony 8 MP CMOS image sensor with STARVIS technology for crystal-clear image quality day and night, with excellent light sensitivity and low image noise for reliable motion detection. It runs on a secure Linux-based operating system with an integrated web server and supports modern TLS encryption. The intuitive web interface (WebUI) is optimized for desktops, tablets, and smartphones and is compatible with major operating systems like Windows, macOS, and Linux. A built-in setup wizard and help system ensure quick and easy installation, even for beginners.

For camera installation, please visit: https://install.instar.com

2. Safety Warnings

Please read the following safety warnings carefully and keep them in a safe place:

Ensure the power cord is not near hot surfaces.
Properly route power and network cables to prevent injuries.
This device is not intended for use by individuals with limited physical, sensory, or mental capabilities, including children, unless supervised by a responsible person.
Children should be supervised to ensure they do not play with the device.
If the power cord is damaged, it must be replaced by the manufacturer, customer service, or a similarly qualified person to avoid injury or damage.
Do not attempt self-repairs, as opening the device voids the warranty. Contact the INSTAR Service Center for any repair needs.
Never immerse the device in water or other liquids for cleaning.
Install the power adapter in a 110/240V power socket.
Use this device only for securing your home, office, or similar places. Obtain necessary permissions if installing in a public area.
This device is intended for indoor use only.
Do not use the camera for purposes other than its intended use.
Avoid installing the device near explosive or flammable substances.
INSTAR is not liable for issues arising from third-party firmware or WebUIs.
Ensure the power supply and camera are kept in a dry area, as they are not designed for outdoor use.

3. Product Features

Hardware

Image Sensor: QFHD Sony STARVIS CMOS Sensor / Resolution 3840 x 2160px
Wide-Angle Lens: Exchangeable 4.3mm lens with a ~100° diagonal field of view
MicroSD Card: Supports up to 1024GB / 1TB (32GB included) for alarm or manual recording
PIR Sensor: Integrated passive infrared motion detector
Mic / Speaker: Integrated microphone and speaker for two-way audio
Alarm In/Out: Built-in alarm input and output for external alarm accessories

Software

Privacy Areas: Mask up to 8 areas in the video to prevent recording.
Alarm Areas: Define up to 8 areas for software motion detection, linkable with PIR.
Alarm Triggers: Supports motion, heat, and noise detection.
Pre-Recording: Records 1-10 seconds before the alarm event.
Notifications: Sends alarm emails and push notifications.
Smart IoT: Smarthome integration via Alarmserver, MQTT(S), and HTTP(S) API.
Video Recording: 15s alarm and/or manual recording on MicroSD.
Video Stream: Supports RTSP, HTTP(S), ONVIF Profile S, MJPEG protocols.
Photo Series: Interval snapshots for website integration or time-lapse videos.
Intercom: Two-way audio communication via the InstarVision app.

Connectivity

P2P: Free point-to-point connectivity with InstarVision, supports IPv6.
DDNS: Free DDNS address for internet connectivity.
Cloud: Optional storage and management of alarm videos in the INSTAR Cloud.
FTP Upload: Uploads alarm images/videos to FTP(S) / SFTP servers.
PoE: Power over Ethernet, IEEE 802.3af.
WPS: WiFi Protected Setup for easy WiFi connection.
WiFi: 2.4 / 5 GHz WiFi, Wi-Fi 5 802.11ac with WPA2/3 encryption.
HTTPS: Secure access to WebUI via HTTPS with TLS encryption.

4. Camera Structure

4.1. Delivery Content

The package includes:

Camera
Bracket
Lens Focal Tool
MicroSD Card
Screws & Dowels
Power Adaptor
Power Cable
LAN Cable
2x Antenna

4.2. Camera Structure Diagram

The camera has the following components:

Photosensor (Twilight switch for IR LEDs)
Lens (Wide-angle, focal length: 4.3mm / field of view: ~100° dia.)
Infrared LEDs (10 IR LEDs for night vision @ 850nm)
Status LEDs (Red: Power; Blue: Network status)
PIR Detector (Integrated passive infrared motion detector)
Loudspeaker (Integrated loudspeaker)
MicroSD Card Slot (For MicroSD/SDXC cards up to 1024GB / 1TB; 32GB included)
Microphone (For audio detection, audio recording, and two-way audio)
Antenna Connector (RP-SMA WiFi antenna connector)
Network Port (RJ45 LAN port for Cat5e LAN cable or higher, connection to router, switch, or PoE switch)
Audio Output (3.5mm jack for earphone / active speaker)
Alarm In/Out (Input for potential free external alarm sensors; Output relay supports up to 24V/1A)
WPS / Reset Button (3 seconds for WPS WiFi setup / 20 seconds for reset)
Power Connector (5V DC 2A - Plug Ø: 1.35mm (in) / 3.5mm (out))
Mount (Standard camera thread for included stand (1/4”-20 UNC))
Camera Label (P2P ID, LAN MAC address, and serial number)

4.3. Status LEDs

Status LED	Blue LED	Red LED
Constant on	Connected to WiFi	N/A
Slow Flashing	Connecting via WPS	Camera at work
Fast Flashing	No connection to WiFi	Upgrading firmware
Off	LED is turned off, or camera is not plugged into power	LED is turned off, or camera is not plugged into power

5. Installation

Follow these steps for initial setup:

Open a web browser and go to: https://install.instar.com to access the Camera Installation Guide.
Select your language and the camera model (IN-8815 4K).
Choose your network connection type:
- a) Connection via LAN cable or PoE (recommended)
- b) Connection directly via WiFi using WPS
Follow each step of the setup wizard.
On the camera's login page, use the default credentials:
- Username: admin
- Password: instar
The Camera Setup Wizard will guide you through the final setup process. You can then configure your camera using the Web User Interface (WebUI).

6. Smartphone Apps

INSTAR offers free apps for Android, iOS (iPhone/iPad), Blackberry, Amazon Kindle, Windows Phone, and Windows 10/11 (Metro). Search for “InstarVision” in your device's app store to install.

The Difference between the App and the Web User Interface (WebUI):

App: The InstarVision app provides easy access to your camera and live stream from anywhere. It allows for daily use functions like alarm activation, playback of recordings, night vision control, camera control, saving positions, and two-way audio. The app is not for initial camera setup.

Web User Interface (WebUI): Accessible via any modern HTML5 web browser. Use the INSTAR Camera Tool to find the camera's IP address and open it in your browser. The WebUI allows full configuration, including setting alarm areas, linking motion detection and PIR to prevent false alarms, and managing settings that can then be controlled via the InstarVision app.

7. Remote Access

The camera supports two methods for remote access to the live video:

7.1. P2P Protocol

The P2P protocol allows quick and easy connection via the InstarVision app, working with any internet connection (local, public IPv4/6, mobile data) without port forwarding.

Install the InstarVision app from your device's app store.
Open the app, tap the “+” symbol, choose “Add Camera” -> “New P2P Camera”.
Alternatively, open the camera's WebUI, navigate to Network -> Remote access, and scan the QR code to add the camera.

7.2. DDNS Service - HTTP(S) Protocol

The DDNS service allows direct access to your camera via your internet router using any modern web browser, the InstarVision app, or third-party software.

In the WebUI, go to Network -> IP configuration. Assign unique HTTP (e.g., 8081) and HTTPS (e.g., 9081) ports for each camera.
Configure port forwarding rules in your router for each assigned port.
In the app, tap the “+” symbol and choose “Add Camera” -> “New IP Camera”.
Alternatively, open the camera's WebUI, navigate to Network -> Remote access, and scan the QR Code to add the camera. Note: DDNS service may not work from your local network; test via an external internet connection.

Port forwarding requires a public IPv4 address. For detailed information on port forwarding and DDNS, please refer to: https://remote.instar.com

8. Camera Reset

To reset the camera to factory settings, press and hold the reset button on the back for 20 seconds. A confirmation sound will be heard upon release. The camera will restart (up to 60 seconds), and all data will be reset. Reconnect the camera to your network using a network cable or WPS. For reinstallation information, visit: https://install.instar.com. After reconnecting, use the INSTAR Camera Tool to find the IP address and open the WebUI for setup.

9. Lens Adjustment

The IN-8815 4K has a standard lens with a depth of field set to approximately 5-10m. If your area of interest is out of focus, adjust the lens accordingly.

Figure 1 & 2: Open the WebUI and view the live video. Use the lens focal tool (included) to turn the lens until the desired object is in focus. Turning clockwise focuses on distant objects; counter-clockwise focuses on closer objects.

10. Online Material

10.1. Online Manual

This printed manual reflects features as of the print date (07.2025). For the latest information, always refer to the online manual: https://manual.instar.de

The online manual covers topics such as:

Using the DDNS service
Setting up port forwarding
Configuring motion detection
Downloading videos from the SD card

10.2. Firmware Update

INSTAR cameras receive free firmware updates. Check for updates in the WebUI under System -> Firmware Update. Download and install the latest firmware via the WebUI. The latest firmware is also available at: https://firmware.instar.de

10.3. Youtube Installation/Setup Videos

Video tutorials explaining port forwarding, FTP(S) upload, motion detection, and more are available on YouTube. Search for “@INSTAR_Germany” or visit: https://www.youtube.com/INSTAR_Germany

10.4. Wiki, Forum & Social Media

INSTAR provides an extensive Wiki, customer forum, and Facebook page:

Wiki: https://wiki.instar.de
Forum: https://forum.instar.com
Facebook: https://www.facebook.com/instar.deutschland

11. INSTAR Cloud

https://cloud.instar.de

The INSTAR Cloud is an optional, paid service for securely backing up recordings. A 30-day free trial is available at https://cloud.instar.de. The INSTAR Cloud is significantly more affordable than other cloud platforms, potentially saving up to 70% on storage costs. It helps sort false alarms from true events.

INSTAR Cloud Features: Smart, Secure, and Scalable

Smart: Features false alarm, object, license plate, and face recognition. Provides clear alarm previews with download options, automatic alarm event deletion, 3-level user management, and supports HTML5 web browsers and smart home devices (Amazon Echo/Alexa, IFTTT).
Secure: Servers are located in German data centers (ISO 27001 certified) with data secured through two physically distinct locations and encrypted transfer.
Scalable: Offers expandable storage space via monthly or yearly subscriptions, with automatic removal of alarm events after a selected period.

12. Technical Data

Image Sensor

Sensor: 1/2.8" QFHD Sony STARVIS IMX415 CMOS Sensor
Lens: f = 4.3mm; F/1.6 (IR Lense) / M12 - S-Mount
Angle of View: ~100° diagonal

Video Properties

Video Encoding: h.265 / h.264 high, main, baseline / MJPEG
Video Framerate: Up to 25fps
Supported Resolutions: 3840x2160, 1920x1080, 1280x720 pixels
Flip / Mirror Image: Horizontal / Vertical
Video Settings: Brightness / Contrast / Saturation / Exposure...

Communication

Network Interface: 10Base-T/100Base-TX Ethernet Port
Wireless: 5GHz / 2.4GHz, Wi-Fi 5 (802.11ac), 2x2 MIMO
WiFi Frequency Range: 2.4-2.4845Ghz, 5.150 - 5.350 / 5.470 - 5.725Ghz
WiFi Transmission Power: <16dBm @ 11b/g, <15dBm @ 11n <18dBm@ 11ac
WPA2 / WPA3 Encryption: WPA2/WPA3-PSK (AES, CCMP) / Enterprise (EAP)
PoE (Power over Ethernet): IEEE 802.3af (+ Pin 4 and 5 / - Pin 7 and 8)

Hardware

PIR Detector: Passive Infrared Motion Detector
Infrared LEDs: 10 LEDs / 5-10m effective range
MicroSD Card Reader: For microSD / SDXC cards up to 1024GB / 1TB
Pan & Tilt: 350° horizontal / 75° vertical
Power Supply: 5V DC 2A (110-240V), 1.35mm / 3.5mm (out)
Power Consumption: max. 9.5W (in normal operation 5W)
Operating Temperature: 5°C to 55°C

Requirements

Web Browser: Web browser supporting HTML5
CPU / Graphic Card: Dual Core (min. 2Ghz) / 256MB+ Graphic Card

13. Warranty & Disposal

13.1. Warranty

INSTAR offers a 2-year Bring-In warranty. Customers can send their camera for free repair (shipping costs to the service center are the customer's responsibility). This warranty excludes cameras with custom-made or third-party firmware/WebUIs not approved by INSTAR and is limited to hardware defects.

When contacting customer service, please have your model and serial number ready. For repairs, contact support@instar.com to request an RMA number.

INSTAR SERVICE CENTER:

INSTAR Deutschland GmbH
Raiffeisenstraße 12
65510 Hünstetten
Germany

Hotline: +49 (6438) 9198992 (Mon-Fri, 7 AM – 12 PM GMT+1)
Website: www.instar.com
Email: support@instar.com

13.2. Disposal of old electrical appliances

In accordance with European Directive 2012/19/EU (WEEE), old electrical appliances must not be disposed of in unsorted municipal waste. They must be collected separately for optimized recycling and to reduce environmental and health impacts. The crossed-out wheeled bin symbol indicates this obligation. Consumers should contact local authorities or retailers for disposal information. Packaging material is recyclable and should be disposed of environmentally friendly.

14. Legal Information

Manufacturer

INSTAR Deutschland GmbH
Auf der Hostert 17
65510 Hünstetten - Germany
Email: info@instar.com
Website: www.instar.com

CE-Declaration of Conformity

INSTAR Deutschland GmbH declares that this product complies with the essential requirements and relevant provisions of Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: https://www.instar.com/legal/eu-declarations

FCC

This device complies with Part 15 of the FCC rules. Operation is subject to two conditions: (1) no harmful interference, and (2) acceptance of any received interference. The complete FCC Compliance Statement can be found at: https://www.instar.com/legal/fcc

INSTAR Deutschland GmbH
Your Specialist for Network and Security Equipments

File Info : application/pdf, 32 Pages, 1.52MB

QuickInstallation-2160p-IN-8815QFHD