Installation Guide for CISCO models including: CG113-W6B, CG113-W6B Catalyst Wireless Gateways, CG113-W6B, Catalyst Wireless Gateways, Wireless Gateways, Gateways
Cisco Catalyst CG113-W6B Wi-Fi 6 IEEE | Tech-America
File Info : application/pdf, 38 Pages, 2.46MB
DocumentDocumentHardware Installation Guide for Cisco Catalyst Wireless Gateways First Published: 2023-01-16 Last Modified: 2023-08-17 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version. Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R) © 2023 Cisco Systems, Inc. All rights reserved. CONTENTS CHAPTER 1 CHAPTER 2 Full Cisco Trademarks with Software License ? Overview 1 Cisco Catalyst Wireless Gateway CG113-W6 2 Package Contents 2 Hardware Specifications 2 Ethernet Interfaces, Power Port, and Reset Button 3 LED Indicators 4 Antenna Information 6 Power Supply 6 Cisco Catalyst Wireless Gateway CG113-4GW6 7 Package Contents 7 Hardware Specifications 7 Ethernet Interfaces and Power Port 8 SIM Card Slots 9 LED Indicators 10 Antenna Information 12 Power Supply 13 Safety Guidelines and Warnings 15 Statement 1071--Warning Definition 15 Statement 407--Japanese Safety Instruction 16 Statement 1004--Installation Instructions 16 Statement 1033--Safety Extra-Low Voltage (SELV)--IEC 60950/ES1IEC 62368 DC Power Supply 16 Statement 1047--Overheating Prevention 16 Hardware Installation Guide for Cisco Catalyst Wireless Gateways iii Contents CHAPTER 3 CHAPTER 4 APPENDIX A APPENDIX B Statement 1074--Comply with Local and National Electrical Codes 17 Install Cisco Catalyst Wireless Gateways 19 Device Placement 19 Install SIMs, LTE Models 20 Power 21 Data Connections 21 Connect Devices 23 Declarations of Conformity and Regulatory Information 25 USA Conformity and Regulatory Information 25 Manufacturers Federal Communication Commission Declaration of Conformity Statement 25 Canada Conformity and Regulatory Information 27 Canada Compliance Statement 27 European Community and UK Conformity and Regulatory Information 28 European Community, Switzerland, Norway, Iceland, and Liechtenstein Compliance 28 United Kingdom Compliance 29 RF Exposure, Additional Information 30 Generic Discussion on RF Exposure 30 Additional Information on RF Exposure 30 Additional References 33 Additional References 33 Hardware Installation Guide for Cisco Catalyst Wireless Gateways iv 1 C H A P T E R Overview Cisco Catalyst Wireless Gateways extend an enterprise network to remote workers, providing numerous advantages: · Hardware-based stable connectivity to an enterprise VPN · Optimized network performance with Wi-Fi 6 · Cellular network connectivity, in supporting models, providing a cellular internet connection (with one active and one standby SIM) for uninterrupted internet connectivity · Separate service set identifiers (SSIDs) for connecting work and personal devices Cisco Catalyst Wireless Gateway connectivity is as follows: · The Cisco Catalyst Wireless Gateway CG113-W6 accesses the internet using a wired WAN connection at a remote site. · The Cisco Catalyst Wireless Gateway CG113-4GW6 accesses the internet using a wired WAN connection at a remote site or using a cellular link. The device supports two SIM cards: one active, and one on standby. If the wired WAN connection fails, the device fails over to the cellular link to ensure internet connectivity. Note The device has a single cellular connection, so only one SIM can be active at a given time. You can configure which of the two SIM slots serves as primary and which serves as secondary (failover). Managing Cisco Catalyst Wireless Gateways Use Cisco SD-WAN Manager to configure and manage Cisco Catalyst Wireless Gateways. Cisco SD-WAN Manager provides a convenient workflow for configuring Wi-Fi, cellular, VPN, and other functionality. Cisco SD-WAN Manager also provides methods for monitoring device performance. · Cisco Catalyst Wireless Gateway CG113-W6, on page 2 · Cisco Catalyst Wireless Gateway CG113-4GW6, on page 7 Hardware Installation Guide for Cisco Catalyst Wireless Gateways 1 Cisco Catalyst Wireless Gateway CG113-W6 Overview Cisco Catalyst Wireless Gateway CG113-W6 The following sections provide hardware specifications and other information about the Cisco Catalyst Wireless Gateway CG113-W6. Package Contents The package for this device contains the following: · Device chassis · Power supply · Pointer card, providing a link to the product documentation Hardware Specifications Table 1: Hardware Specifications, Cisco Catalyst Wireless Gateway CG113-W6 Item Specifications Interfaces 2.5 Gigabit ethernet 1 1 Gigabit ethernet 2 Wi-Fi Wi-Fi bands 2.4 GHz, 5 GHz Antennas Dual 2x2 MIMO (internal) Cellular None Operating Conditions Temperature 0 to 45 (32 to 113) Humidity 10 to 90% RH Non-condensing Altitude 3000 m (10,000 ft) Storage Conditions Temperature -25 to 70 (-13 to 158) Humidity 5 to 95% RH Non-condensing Altitude 4570 m (15,000 ft) Hardware Installation Guide for Cisco Catalyst Wireless Gateways 2 Overview Ethernet Interfaces, Power Port, and Reset Button Item Specifications Power Power adapter 12V, 3A maximum Models, according to region: CG113-4G-PWR-US, -EU, -AU Power connector USB-C Mounting and Accessories The device is installed on a desk or other flat surface. No additional mounting equipment is supplied. Ethernet Interfaces, Power Port, and Reset Button The ethernet interfaces, power port, and reset button are located on the back panel of the device. Figure 1: Back Panel Hardware Installation Guide for Cisco Catalyst Wireless Gateways 3 LED Indicators Figure 2: Reset Button, Interfaces, and Power Port Overview 1 Reset button 2 1 Gbps ethernet interfaces 3 2.5 Gbps ethernet interface 4 USB-C power port LED Indicators The single LED indicator appears on the front panel of the device. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 4 Overview Figure 3: Front Panel LED Indicators Figure 4: LED Indicator on Front Panel 1 LED indicator for Wi-Fi connectivity Table 2: LED Indicator Behavior LED Wi-Fi Color Red, blinking Red, solid Green, solid Blue, solid Description Device is booting Wi-Fi not ready Wi-Fi ready, no devices connected Wi-Fi ready, one or more devices connected Hardware Installation Guide for Cisco Catalyst Wireless Gateways 5 Antenna Information Overview Antenna Information Antennas, Gain, and Impedance Table 3: List of Internal Antennas Supported on Cisco CG113-W6 Antenna Type Antenna type: Wi-Fi Single-Port/Dual Band/Omni-directional (Linear Polarization, Wi-Fi 1) Antenna type: Wi-Fi Single-Port/Dual Band/Omni-directional (Linear Polarization, Wi-Fi 2) Antenna Gain 2.4GHz: 4dBi 5GHz: 5dBi 2.4GHz: 2.6dBi 5GHz: 4.8dBi Antenna Impedance 50 ohms 50 ohms Maximum Transmitted Power The frequency and the maximum transmitted power are listed below: 2412-2472MHz: 19.99 dBm 5180-5240MHz: 22.92 dBm 5260-5320MHz: 22.95 dBm 5500-5700: 29.97 dBm Power Supply The following power supplies are included with the device, depending on region. Table 4: Power Supply Part and Model Numbers, by Region Region USA Australia EU, UK Cisco Part Number CG113-4G-PWR-US CG113-4G-PWR-AU CG113-4G-PWR-EU Model Number ADH-36DW B ADH-36DW E ADH-36DW C Table 5: Power Supply Specifications Specification Input Description 100-240V AC 50-60Hz Hardware Installation Guide for Cisco Catalyst Wireless Gateways 6 Overview Cisco Catalyst Wireless Gateway CG113-4GW6 Cisco Catalyst Wireless Gateway CG113-4GW6 The following sections provide hardware specifications and other information about the Cisco Catalyst Wireless Gateway CG113-4GW6. Package Contents The package for this device contains the following: · Device chassis · Power supply · Pointer card, providing a link to the product documentation Hardware Specifications Table 6: Hardware Specifications, Cisco Catalyst Wireless Gateway CG113-4GW6 Item Specifications Interfaces 2.5 Gigabit ethernet 1 1 Gigabit ethernet 2 Wi-Fi Wi-Fi bands 2.4 GHz, 5 GHz Antennas Dual 2x2 MIMO (internal) Cellular SIM slots 2 Cellular bands 4G/Cat7 Operating Conditions Temperature 0 to 45 (32 to 113) Humidity 10 to 90% RH Non-condensing Altitude 3000 m (10,000 ft) Storage Conditions Temperature -25 to 70 (-13 to 158) Humidity 5 to 95% RH Non-condensing Hardware Installation Guide for Cisco Catalyst Wireless Gateways 7 Ethernet Interfaces and Power Port Overview Item Specifications Altitude 4570 m (15,000 ft) Power Power adapter 12V, 3A maximum Models, according to region: CG113-4G-PWR-US, -EU, -AU Power connector USB-C Mounting and Accessories The device is installed on a desk or other flat surface. No additional mounting equipment is supplied. Ethernet Interfaces and Power Port The ethernet interfaces, power port, and reset button are located on the back panel of the device. Figure 5: Back Panel Hardware Installation Guide for Cisco Catalyst Wireless Gateways 8 Overview Figure 6: Reset Button, Interfaces, and Power Port SIM Card Slots 1 Reset button 2 1 Gbps ethernet interfaces 3 2.5 Gbps ethernet interface 4 USB-C power port SIM Card Slots The SIM card slots are accessible from the bottom panel of the device. For information about installing SIM cards, see Install SIMs, LTE Models, on page 20. Figure 7: Bottom Panel 1 Cover for SIM card slots Hardware Installation Guide for Cisco Catalyst Wireless Gateways 9 LED Indicators Figure 8: SIM Card Slots, with the Cover Removed 1 SIM card slots 0 and 1 Figure 9: SIM Card Slots LED Indicators The LED indicators appear on the front panel of the device. Overview Hardware Installation Guide for Cisco Catalyst Wireless Gateways 10 Overview Figure 10: Front Panel LED Indicators Figure 11: LED Indicators on Front Panel 1 LED indicator for cellular connectivity 2 LED indicator for Wi-Fi connectivity Table 7: LED Indicator Behavior LED Wi-Fi Color Red, blinking Red, solid Green, solid Blue, solid Green, blinking Description Device is booting Wi-Fi not ready Wi-Fi ready, no devices connected Wi-Fi ready, one or more devices connected Firmware upgrade in progress Hardware Installation Guide for Cisco Catalyst Wireless Gateways 11 Antenna Information Overview LED Color Description 4G Red, blinking Device is booting Red, solid Completed boot, no SIM detected, not connected to network Green, solid SIM detected, connected to network, wired connection is active and cellular connection is standby Green, blinking Firmware upgrade in progress Blue, blinking SIM detected, connected to network, cellular connection is active, weak signal Blue, solid SIM detected, connected to network, cellular connection is active, strong signal Antenna Information Antennas, Gain, and Impedance Table 8: List of Internal Antennas Supported on Cisco CG113-4GW6 (Includes LTE) Antenna Type Antenna type: Wi-Fi Single-Port/Dual Band/Omni-directional (Linear Polarization, Wi-Fi 1) Antenna type: Wi-Fi Single-Port/Dual Band/Omni-directional (Linear Polarization, Wi-Fi 2) Antenna type: LTE Single-Port/LTE Full Band/Omni-directional (Mixed Polarization, LTE Main) Antenna type: LTE Single-Port/LTE Full Band/Omni-directional (Vertical Polarization, LTE Auxiliary) Antenna Gain 2.4GHz: 4dBi 5GHz: 5dBi Antenna Impedance 50 ohms 2.4GHz: 2.6dBi 5GHz: 4.8dBi 50 ohms 617-960MHz: 2.1dBi 1710-2700MHz: 4.1dBi 3300-3800MHz: 3.6dBi 50 ohms 617-960MHz: 2.1dBi 1710-2700MHz: 4.1dBi 3300-3800MHz: 3.6dBi 50 ohms Maximum Transmitted Power The frequency and the maximum transmitted power are listed below: 2412-2472MHz: 19.99 dBm Hardware Installation Guide for Cisco Catalyst Wireless Gateways 12 Overview Power Supply 5180-5240MHz: 22.92 dBm 5260-5320MHz: 22.95 dBm 5500-5700: 29.97 dBm Power Supply The following power supplies are included with the device, depending on region. Table 9: Power Supply Part and Model Numbers, by Region Region USA Australia EU, UK Cisco Part Number CG113-4G-PWR-US CG113-4G-PWR-AU CG113-4G-PWR-EU Model Number ADH-36DW B ADH-36DW E ADH-36DW C Table 10: Power Supply Specifications Specification Input Description 100-240V AC 50-60Hz Hardware Installation Guide for Cisco Catalyst Wireless Gateways 13 Power Supply Overview Hardware Installation Guide for Cisco Catalyst Wireless Gateways 14 2 C H A P T E R Safety Guidelines and Warnings · Statement 1071--Warning Definition, on page 15 · Statement 407--Japanese Safety Instruction, on page 16 · Statement 1004--Installation Instructions, on page 16 · Statement 1033--Safety Extra-Low Voltage (SELV)--IEC 60950/ES1IEC 62368 DC Power Supply, on page 16 · Statement 1047--Overheating Prevention, on page 16 · Statement 1074--Comply with Local and National Electrical Codes, on page 17 Statement 1071--Warning Definition Warning IMPORTANT SAFETY INSTRUCTIONS Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Read the installation instructions before using, installing, or connecting the system to the power source. Use the statement number provided at the end of each warning statement to locate its translation in the translated safety warnings for this device. SAVE THESE INSTRUCTIONS Hardware Installation Guide for Cisco Catalyst Wireless Gateways 15 Statement 407--Japanese Safety Instruction Safety Guidelines and Warnings Statement 407--Japanese Safety Instruction Note You are strongly advised to read the safety instruction before using the product. https://www.cisco.com/web/JP/techdoc/pldoc/pldoc.html When installing the product, use the provided or designated connection cables/power cables/AC adapters. Statement 1004--Installation Instructions Warning Read the installation instructions before using, installing, or connecting the system to the power source. Statement 1033--Safety Extra-Low Voltage (SELV)--IEC 60950/ES1IEC 62368 DC Power Supply Warning To reduce risk of electric shock, connect the unit only to a DC power source that complies with the SELV requirements in IEC 60950-based safety standards or ES1 requirements in IEC 62368-based safety standards. Statement 1047--Overheating Prevention Warning To reduce the risk of fire or bodily injury, do not operate the unit in an area that exceeds the maximum recommended ambient temperature of: 45. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 16 Safety Guidelines and Warnings Statement 1074--Comply with Local and National Electrical Codes Statement 1074--Comply with Local and National Electrical Codes Warning To reduce risk of electric shock or fire, installation of the equipment must comply with local and national electrical codes. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 17 Statement 1074--Comply with Local and National Electrical Codes Safety Guidelines and Warnings Hardware Installation Guide for Cisco Catalyst Wireless Gateways 18 3 C H A P T E R Install Cisco Catalyst Wireless Gateways · Device Placement, on page 19 · Install SIMs, LTE Models, on page 20 · Power, on page 21 · Data Connections, on page 21 Device Placement Place the Cisco Catalyst Wireless Gateway on a flat surface, with access to a household power outlet and to an ethernet connection providing internet connectivity. The device has two rubber pads for resting on a desk or shelf. No special hardware is required for mounting. The dimensions of the device are shown in the following illustration. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 19 Install SIMs, LTE Models Figure 12: Product Dimensions Install Cisco Catalyst Wireless Gateways Install SIMs, LTE Models For LTE models, install one or two SIM cards to provide cellular connectivity. For an illustration of the SIM card slots, see SIM Card Slots, on page 9. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 20 Install Cisco Catalyst Wireless Gateways Power Required Equipment Small Phillips-head screwdriver Install SIMs 1. On the bottom of the Cisco Catalyst Wireless Gateway, open the cover for the SIM slots using the a small Phillips-head screwdriver. 2. Install either one (1) or two (2) SIM cards in the two slots, marked 0 and 1. If you are installing two SIM cards, make note of which SIM card you place in each slot. This information is required during configuration of the two slots as primary and secondary. 3. Replace the cover for the SIM slots. Power Connect the power adapter to an household power outlet, and connect its cable to the USB-C port on the back of the Cisco Catalyst Wireless Gateway. Ensure that the power cable is properly secured. Data Connections Ensure that any data cables connected to the device are properly secured. Table 11: Data Connections Connection Internet Description Connect the device to a WAN providing internet access, using the 2.5 Gbps ethernet interface. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 21 Data Connections Install Cisco Catalyst Wireless Gateways Hardware Installation Guide for Cisco Catalyst Wireless Gateways 22 4 C H A P T E R Connect Devices Ensure that any data cables connected to the device are properly secured. Table 12: Connections Connection Description Non-corporate wired LAN To connect a non-corporate device, such as a personal laptop, by wired ethernet, connect it to the 1 Gbps ethernet interface that your organization has configured for general, non-corporate use. For information about which interface this is, contact your organization. Corporate Wi-Fi To connect your corporate device, such as a work laptop, by Wi-Fi, connect it to the Wi-Fi SSID that your organization has configured for corporate use. For information about which SSID this is, contact your organization. Non-corporate Wi-Fi To connect your non-corporate device, such as a work laptop, by Wi-Fi, connect it to the Wi-Fi SSID that your organization has configured for general, non-corporate use. For information about which SSID this is, contact your organization. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 23 Connect Devices Hardware Installation Guide for Cisco Catalyst Wireless Gateways 24 A A P P E N D I X Declarations of Conformity and Regulatory Information · USA Conformity and Regulatory Information, on page 25 · Canada Conformity and Regulatory Information, on page 27 · European Community and UK Conformity and Regulatory Information, on page 28 · RF Exposure, Additional Information, on page 30 USA Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement FCC Mark Certifications Model CG113-W6B CG113-4GW6B Certification Number (Wi-Fi): LDKCG1132477 (Wi-Fi): LDKCG1132477 (LTE): N7NEM74B Hardware Installation Guide for Cisco Catalyst Wireless Gateways 25 Declarations of Conformity and Regulatory Information Declarations of Conformity and Regulatory Information Manufacturer Cisco Systems, Inc.170 West Tasman Drive, San Jose, CA 95134-1706 USA Compliance This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radiofrequency energy, and if not installed and used according to the instructions, it may cause harmful interference. Hence, professional installation is recommended. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna · Increase separation between the equipment and receiver · Connect the equipment to an outlet on a circuit different from which the receiver is connected · Consult the dealer or an experienced radio/TV technician Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 44cm between the radiator and your body. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 26 Declarations of Conformity and Regulatory Information Canada Conformity and Regulatory Information Canada Conformity and Regulatory Information Canada Compliance Statement Certifications Model CG113-W6A CG113-4GW6A Certification Number (Wi-Fi): 2461N-CG1132477 (Wi-Fi): 2461N-CG1132477 (LTE): 2417C-EM74B Manufacturer Cisco Systems, Inc.170 West Tasman Drive, San Jose, CA 95134-1706 USA Product Use · For indoor use only. Pour une utilisation en intérieur uniquement. · The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. · The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. · For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 25cm de distance entre la source de rayonnement et votre corps. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 27 European Community and UK Conformity and Regulatory Information Declarations of Conformity and Regulatory Information License-Exempt Tranmitters/Receivers This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes au (x) RSS (s) exemptés de licence d'Innovation, Sciences et Développement économique Canada. L'opération est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil. European Community and UK Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein Compliance CE Mark The product carries the CE Mark: Models CG113-W6E CG113-4GW6E Manufacturer Cisco Systems, Inc.125 West Tasman Drive, San Jose, CA 95134-1706 USA Importer Cisco Systems, Inc.125 West Tasman Drive, San Jose, CA 95134-1706 USA Product Use The device is restricted to indoor use only. Hardware Installation Guide for Cisco Catalyst Wireless Gateways 28 Declarations of Conformity and Regulatory Information United Kingdom Compliance This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. Maximum Transmitted Power The frequency and the maximum transmitted power in EU are listed below: 2412-2472MHz: 19.99 dBm 5180-5240MHz: 22.92 dBm 5260-5320MHz: 22.95 dBm 5500-5700: 29.97 dBm Declaration of Conformity Hereby, Cisco Systems, Inc. declares that the radio equipment type CG113-4GW6E, CG113-W6E is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.cisco.com/web/dofc/EU89192.pdf European Community and UK Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. United Kingdom Compliance UKCA Mark Models CG113-W6E CG113-4GW6E Hardware Installation Guide for Cisco Catalyst Wireless Gateways 29 RF Exposure, Additional Information Declarations of Conformity and Regulatory Information Manufacturer Cisco Systems, Inc.125 West Tasman Drive, San Jose, CA 95134-1706 USA Importer Cisco Systems, Inc.125 West Tasman Drive, San Jose, CA 95134-1706 USA Product Use The device is restricted to indoor use only. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body. Declaration of Conformity The full text of the EU declaration of conformity is available at the following internet address: https://www.cisco.com/web/dofc/UK89249.pdf European Community and UK Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. RF Exposure, Additional Information This section contains information on compliance with guidelines related to RF exposure. Generic Discussion on RF Exposure The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies: · US 47 Code of Federal Regulations Part 2 Subpart J · American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (99) · International Commission on Non Ionizing Radiation Protection (ICNIRP) 98 · Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz · Australia Radiation Protection Standard To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories. Additional Information on RF Exposure You can find additional information on the subject at the following links: Hardware Installation Guide for Cisco Catalyst Wireless Gateways 30 Declarations of Conformity and Regulatory Information Declarations of Conformity and Regulatory Information · Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL: http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm · FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields · FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields You can obtain additional information from the following organizations: · World Health Organization Internal Commission on Non-Ionizing Radiation Protection · United Kingdom, National Radiological Protection Board · Cellular Telecommunications Association at this URL: https://www.ctia.org · The Mobile & Wireless Forum at this URL: https://www.mwfai.org Hardware Installation Guide for Cisco Catalyst Wireless Gateways 31 Declarations of Conformity and Regulatory Information Declarations of Conformity and Regulatory Information Hardware Installation Guide for Cisco Catalyst Wireless Gateways 32 B A P P E N D I X Additional References · Additional References, on page 33 Additional References Reference Description Release Notes for Cisco Catalyst Wireless Gateways Description of new features in each release, and lists of any open or resolved caveats in each release. Cisco Catalyst Wireless Gateways Software Configuration Guide Cisco Catalyst Wireless Gateway Web-Based Interface Description of the web-based interface for monitoring and configuring Cisco Catalyst Wireless Gateways. Regulatory Compliance and Safety Information Regulatory compliance and safety information. Cisco Catalyst Wireless Gateways Hardware Installation Guide for Cisco Catalyst Wireless Gateways 33 Additional References Additional References Hardware Installation Guide for Cisco Catalyst Wireless Gateways 34
AI Infrastructure, Secure Networking, and Software Solutions - Cisco
CTIA - Home
Mobile & Wireless Forum