KLIM Pods User Manual
Important Safety Information
Warning: This product contains lithium batteries. Do not expose it to strong sunlight or fire to avoid risk of damage, fire or explosion.
Product Overview
This document provides instructions for the KLIM Pods wireless earbuds.
Diagram of Components
The KLIM Pods system includes earbuds and a charging case. Key components are identified as:
- 1. Charging indicators
- 2. USB charging port
- 3. Earphone LED indicator
- 4. Multi-function button
- 5. Charging contacts
Operation and Controls
| Function | Action |
|---|---|
| Play / Pause | Press the button on either earphone once. |
| Skip track | Press the button on the right earbud 2 times in quick succession. |
| Previous track | Press the button on the right earbud 3 times in quick succession. |
| Volume down | Press the button on the left earbud 3 times in quick succession. |
| Volume up | Press the button on the left earbud 2 times in quick succession. |
| Answer / Finish Phone Call | Press the button on the right earbud once to answer or finish a call. |
| Reject incoming call | Hold the button on the right earbud for 2 seconds. Release when you hear a beep to avoid turning off the earbuds. |
| Voice Control | Press and hold the button on either earbud for 2 seconds to activate your device's voice control (Siri, Google Voice). In this state, press once to exit voice control. |
First-time Use and Charging
Before first use, remove the protective film from the earphone contacts. Place the earbuds in the charging case. Connect the case to a computer or power outlet using the supplied cable. An initial full charge typically takes about 2 hours. The charging case can recharge the earbuds 4-5 times before needing to be recharged itself.
Charging Case LED Indicators
- Off: Not charging / fully charged
- Red: Case charging
- Blue: Earphones charging
- Purple: Case and earphones charging
Pairing Instructions
- Remove both earbuds from the charging case simultaneously. They will connect to each other and begin pairing automatically (indicated by flashing red and blue lights). If pairing fails, press and hold the multi-function button for 2 seconds. Once connected, the left earbud's LED will turn off, while the right earbud's LED will remain on for 2 seconds.
- Enable Bluetooth on your device and select "KLIM Pods" from the list of available devices. Upon successful connection, the LEDs on both earbuds will flash blue for 2 seconds.
Note: If pairing fails, the blue light will flash slowly, and the earbuds will automatically shut down after 10 minutes. Placing the earbuds back into the charging case will disconnect them and initiate charging. If the paired Bluetooth device is disconnected or goes out of range, a new pairing process will commence.
Single Earbud Mode
You can use a single earbud and pair it individually. To do this, remove only one earbud from the charging case. The blue LED will flash. Press and hold the control button for 4-5 seconds to enter pairing mode and pair the earbud normally. Note: Volume adjustment is not available in Single Earbud mode.
To use both earbuds together again, place both earbuds back into the charging case simultaneously. They will turn off automatically. Remove both earbuds from the case to initiate pairing.
Troubleshooting Sync Issues
IMPORTANT: If the earbuds are not synced with each other (indicated by the left earbud flashing purple), follow these steps to reconnect them:
- Remove the earbuds from the case. Press and hold both control buttons on the earbuds for 6 seconds until both earphones turn off, then release them.
- Press and hold both control buttons again for 10 seconds, then place them back into the charging case.
- Remove both earbuds from the case simultaneously; they will connect to each other automatically.
FAQ and Support
Frequently Asked Questions
- Q: Only one of the earbuds works.
- A: Check that one of the earbuds is not in Single Earbud mode.
- Q: There are two devices called "KLIM Pods" in the Bluetooth list on my device.
- A: Delete both connections, then pair again. If two device names still appear, ensure the earbuds are not being used in Single Earbud Mode.
Contact Support
For further assistance, KLIM Technologies' team of specialists is available to answer your questions within 24 hours. Please contact support@klimtechnologies.com.
