SPORTNOW Basketball Hoop Assembly Instructions
Model Numbers: A61-035V00, A61-037V01, A61-037V00
Important Information
Retain for future reference. Read carefully.
Estimated assembly time: 30 minutes
Tools required: Screwdriver
Safety Instructions
To ensure safety, do not assemble this product without following all instructions. Check all packaging, ensuring all parts are present and not damaged. A high risk of serious injury can occur if this appliance is not installed, maintained, and used properly.
- The equipment should be moved by at least three adults, who are capable of handling its weight. Children should not move this appliance.
- Check the base regularly (if possible) for leakages. Slow leaks can cause the product to tip over.
- Stand in front of the product and pull the pole forward, so it is balanced on its wheels.
- Move the appliance to the desired location and carefully set the base down.
Warnings:
- Do not hang on the rim or any parts of the product, including backboard, support braces, and net.
- Do not use if parts are damaged. If there are any issues with parts, please contact customer service.
- Do not leave the system in an upright position without filling the base with water, as it could tip over and cause injury.
- Do not fill the base with water in freezing temperatures, as the water could freeze and cause damage. Instead, use sand to fill the base.
- Keep top pole and lifter pole covered with the cap at all times.
- When playing, do not wear jewelry; it could get tangled or damaged.
- When adjusting height or moving the product, keep hands away from moving parts.
- Do not allow children to move or adjust the product.
Product Moving:
- Adjust the product to its lowest level before moving.
- Avoid friction with the ground while moving.
- Rise the product slowly.
Parts List
| NO. | QTY | NAME | REMARK |
|---|---|---|---|
| A | 1 | M8*40MM Plastic head knob | knob fix Top pole(L)&Middle pole(K) |
| B | 2 | M8*35MM | Connect Rim(N),Backboard(O)&Top pole(L) |
| C | 2 | M8*16MM | Fix Backboard brace(G)&Backboard(0) |
| D | 2 | M8*65MM | Fix Top pole(L)&Middle pole(K) Fix Top pole(L)& Backboard brace(G) |
| E | 3 | M8*65MM | Connect Bottom pole(J)& Base(P) |
| F | 2 | M8*20MM | Connect Base(P)&Support brace(H) |
| G | 2 | Backboard brace | Connect Backboard(O)&Top pole(L) |
| H | 2 | Support brace | Connect Bottom pole(J)& Base(P) |
| I | 2 | Wheel | |
| J | 1 | Bottom Pole | 50*50MM Square Tube |
| K | 1 | Middle Pole | 45*45MM Square Tube |
| L | 1 | Top Pole | 40*40MM Square Tube |
| M | 1 | Wheel Shaft | |
| N | 1 | Rim | |
| O | 1 | Backboard | |
| P | 1 | Base |
Assembly Details
Step 1: Assembly wheelshaft, wheel and bottom tube
Insert the wheel shaft (M) into the front holes of the base (P), also insert the left wheel (I), bottom tube (J) and right wheel (I) in turn as shown.
Diagram: Shows the base (P) with the wheel shaft (M) inserted, and wheels (I) and bottom tube (J) being attached.
Step 2: Assembly Base
Fix one end of the 2 support braces (H) on the base by screws (F), then fix another end of the 2 support braces (H) on the bottom tube (J) by screw (E) as shown. Finally, fill the base with water or sand to keep steady.
Diagram: Shows the base (P) with support braces (H) attached to it and the bottom tube (J) using screws (F) and (E).
Step 3: Assembly of the rim, backboard and top tube
Assemble the rim (N), backboard (O) and top tube (L) by screws (B) as shown.
Diagram: Shows the rim (N), backboard (O), and top tube (L) being connected with screws (B).
Step 4: Assembly of backboard braces
Fix one end of the backboard braces (G) on top tube (L) by screw (D), then fix another end of the backboard braces (G) on backboard by screw (C) as shown.
Diagram: Shows the backboard braces (G) being attached to the top tube (L) with screw (D) and to the backboard (O) with screw (C).
Step 5: Assembly of top tube and middle tube
Insert the top tube (L) into the middle tube (K). The height is adjustable as per requirement. Lock the tubes by the knob (A), (D) as shown. Notice: The adjustment range is from 2.1m--2.6m.
Diagram: Shows the top tube (L) inserted into the middle tube (K), with knobs (A) and (D) used to secure them.
Step 6: Assembly of middle tube and bottom tube
Insert the middle tube (K) into the bottom tube (J), use the plastic head knob (E) to lock them as shown.
Diagram: Shows the middle tube (K) inserted into the bottom tube (J), secured by knob (E).
Step 7: Install net on Rim
Install the net on the Rim (N) as shown.
Diagram: Two close-up views showing how to attach the net to the rim.
Contact Information
EN: Our contact details are below:
ES: Nuestros datos de contacto son los siguientes:
PT: Os nossos dados de contacto são os seguintes:
| Country | Phone | |
|---|---|---|
| UK | 0044-800-240-4004 | enquiries@mhstar.co.uk |
| ES&PT | 0034-931294512 | atencioncliente@aosom.es |
Importer Address:
MH STAR UK LTD
Unit 27, Perivale Park,
Horsenden lane South
Perivale, UB6 7RH
MADE IN CHINA
Importado Por:
SPANISH AOSOM, S.L.
C/ ROC GROS, N° 15.
08550, ELS HOSTALETS DE BALENYÀ, SPAIN.
B66295775
WWW.AOSOM.ES
ATENCIONCLIENTE@AOSOM.ES
TEL: 931294512
HECHO EN CHINA
