SPL Washrooms - Equipping Commercial Washrooms Since 1997
Installation Guide for SPL Washrooms models including: SANELA Husa Sensor Tap, SANELA, Husa Sensor Tap, Sensor Tap, Tap
File Info : application/pdf, 10 Pages, 1.14MB
DocumentDocumentHUSA - BATTERY POWERED Installation & maintenance instructions. General Information · Designed for indoor use only. Do not expose to elements of nature. · All plumbing and electrical connection must be made in accordance with AUS / NZ standards. Warnings · Read all instructions before attempting to install this system. It is recommended a qualified & registered plumber completes the install. · Ensure pipe work is thoroughly flushed before installing the solenoid assembly. Solenoid components are susceptible to debris and require additional flushing compared to a standard plumbing fixture. · Consideration should be given to any regulations relating to an air gap, an air break or double check valve to protect against back flow. splwashrooms.co.nz 2 Operating Instructions and Parts Manual Please read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/ or property damage. Retain instructions for future reference. Sanela Husa Sensor Tap Sensor activated tapware for cold and pre-mixed water. High quality electronics combined with elegant aesthetics. Specifications Finish Water Temperature Power Supply Control Operating Voltage Active Range Recommended Pressure Rate of Flow Water Inlet Dimensions Warranty Chrome For cold, hot or premixed water (thermostatic mixing valve available) 6V (4 x AA alkaline batteries) 2 years @ 100 cycles / day Infra-red sensor Battery 6V, 6W Standard 0.2 - 0.26 m, START/STOP program 0.25 - 7.75 secs 0.1 - 0.6 Mpa (1-6 Bar) 3.8 l/min (6 l/min or 1.9L/m available on request) Male thread G 1/2" Height 346mm, Depth 210mm, Tap Diameter Ø 50, Hole Ø 35mm, Nosing 190mm, Discharge Height 230mm 24 Months Planning · Ensure an appropriate piping design (sizing etc). This will eliminate issues arising from flow, pressure and water hammering. · Where appropriate install necessary filters, water hammering arrestors and water pressure reducing valves (recommended pressure 1 to 6 bar). This will minimise future maintenance. · Install the angle valve to enable ease of future maintenance. Tempered Water · An appropriate thermostatic mixing valve (TMV3) should be installed to ensure a safe regulated water temperature. These are available from SPL SST THERMO VALVE splwashrooms.co.nz 3 Components to battery housing to solenoid valve Standard Functions 1 Mounting screws 2 Faucet spout 3 Faucet base 4 Mounting plate 5 Gasket 6 Hex nut 7 Connection hose 8 4 x AA batteries 9 Solenoid valve 10 Connection hoses 11 Battery housing 12 Washer 13 Filter 14 Angle valves (x2) Hands within active range, water flows STOP Hands removed from active range, water stops SENSING RANGE Operating pressure range After 5 mins of use water will stop splwashrooms.co.nz 4 Faucet Installation Install 1/2" angle valve(s) Flush lines thoroughly Connect faucet spout and base together, insert mounting screw and fit gasket Fit connection hose into base of faucet splwashrooms.co.nz Pass mounting screw, hose and electrical connections through vanity 5 Fit remaining gasket, mounting plate and hex nut Fit remaining connection hose, connect washer and solenoid. Note arrow on solenoid valve for water flow direction Fit filter into angle valve and connect hoses Remove lid of battery housing Insert 4 x AA batteries into battery housing ensuring correct polarity Place batteries back in housing and close lid securely splwashrooms.co.nz 6 Turn angle valves on and check all connections Connect battery to faucet by aligning guide lines on respective cables. Secure battery housing to the wall using the adhesive strips provided Do not come within active range Important Once the battery housing is connected, faucet will automatically adjust sensing range during first 10 seconds. The LED on sensor will continually flash, do not come in active range during this time. · Pipework is required to be flushed thoroughly prior to faucet and solenoid installation. Foreign debris may reduce level of flow and in some cases damage the solenoid valve. · The sensor of the faucet must not be obstructed. · Avoid positioning reflective objects or surfaces in front of the faucet sensor. This can cause false activation i.e. mirrors opposite faucet. With wall mounted faucets pay particular attention to the distance between the bottom of the basin and the faucet (minimum of 300mm) and the location and material of the basin waste (avoid mounting directly over the waste and/or choose non reflective options). · All plumbing and electrical installation must be carried out by a qualified person and in accordance with applicable codes and regulations. splwashrooms.co.nz 7 Note: If you require to modify any of the factory settings please request the Sanela remote SLD03. Activation Range Time Delay Hygienic Flush Maintenance · It is recommended that the solenoid valve and all filters be inspected for foreign debris and cleaned annually (more frequently if necessary) · Clean faucet regularly using soapy water and a soft cloth or wet sponge · DO NOT clean faucet with any abrasive material or chlorine/acid based cleaning product. This may damage the filter of the infrared sensor and/or the finishing of the faucet · Check batteries periodically. Flashing lights will indicate when the battery voltage is below 10% capacity splwashrooms.co.nz 8 Troubleshooting Symptom Possible Cause No water flow is LED on sensor flashing red when hands are within active range? a. Water supply b. Water connections c. Filter is clogged d. Faucet to solenoid power connection e. Batteries are flat f. Faulty solenoid No water flow LED on sensor NOT flashing when hands are within active range. a. Power supply b. IR sensor damaged c. Faulty IR sensor Water doesn't stop flowing a. Dirty IR sensor b. Obstruction in detection zone c. Water drop on sensor eye d. Ghost sensing due to reflection e. Debris in solenoid Reduced flow rate a. Filter clogged b. Aerator clogged c. Water supply Corrective Action a. Ensure water at source b. Ensure connections c. Clean filter (angle valve and solenoid) d. Reconnect plugs from faucet to solenoid valve e. Replace batteries f. Replace solenoid a. Check battery holder connection b. Replace IR sensor filter c. Replace IR sensor a. Clean IR sensor b. Remove obstruction c. Wipe sensor d. Remove reflective surface or reposition e. Clean and/or replace solenoid a. Clean filter b. Clean aerator c. Check pressure / flow at source splwashrooms.co.nz 9 Supreme Comprehensive Warranty Your Sanela Sensor Tap is fully guaranteed against defective materials and faulty workmanship commencing from the date of sale (according to SPL's records), subject to it being installed and maintained in accordance with the manufacturer's instructions. SPL (2021) Limited warrants that should any part of the sensor tap fail within the given warranty period (24 months), it will be remedied by SPL. The tap should be returned to SPL (2021) Limited for all warranty claims. The cost of cartage will be payable by the customer. Due to the significant variation in tradesmen's knowledge, experience, and productivity, labour charges will NOT be accepted unconditionally. We strongly recommend contacting our office for advice before proceeding with any warranty repairs. This warranty excludes: · Incorrect installation, or installation that does not specifically follow the installation guidelines supplied · Defects arising from improper installation, or incorrect electrical supply where applicable · Failure to follow manufacturer's maintenance instructions · Damage/Failure resulting from: - the use of non-authorised parts - authorised parts not installed in accordance with the manufacturer's instructions - accidental damage, negligent use, misuse, vandalism, neglect - damage caused either directly or indirectly by external sources (incorrect power supply, natural disaster, or insect infestation) · Water ingress caused by property maintenance or flooding · Negligent cleaning practices (water ingress, harmful chemical etc) The above includes consequential damage to any other goods, furnishings, or property. · Normal wear and tear and consumable parts (batteries etc) · This warranty does not displace any statutory warranty in relation to the tap but any liability of SPL (2021) Limited under any statutory warranty will be limited to a replacement or repair of the tap or payment of the cost of such replacement or repair at the sole discretion of SPL (2021) Limited Note: · Warranty only extends to products purchased and installed in New Zealand. · Contamination or poor water quality is not covered by product warranty. · Damage to solenoid caused by inadequate flushing or excess water pressure is not covered by the product warranty. SPL Limited Cambridge 3434 New Zealand p. +64 7 823 5790 e. office@splwashrooms.co.nz splwashrooms.co.nz