Gira IP Flush-Mounted Radio 2320

Gira Giersiepen GmbH & Co. KG

Elektro-Installations-Systeme
Industriegebiet Mermbach
Dahlienstraße 42477 Radevormwald
Postfach 1220, 42461 Radevormwald
Deutschland

Tel: +49(0)21 95 - 602-0
Fax: +49(0)21 95 - 602-191
www.gira.de
info@gira.de

Safety

Electrical devices may only be installed and connected by a qualified electrician!

These instructions are an integral part of the product and must remain with the end customer.

Accessories

• Speaker for the IP flush-mounted radio (Item no. 2282 ..)

Intended Use

• Playback of internet radio stations via connected speakers or speakers for mobile devices, operation of a Sonos music system.
• Possible to operate and programme using a mobile end device (smartphone or tablet) via Bluetooth with the Gira System 3000 app.
• Installation in DIN 49073 device box.

Device Components

The IP flush-mounted radio system consists of the following main components:

• 1: IP flush-mounted radio operating top unit with display and operating surface
• 2: Speaker cover
• 3: Cover frame
• 4: Speaker insert
• 5: IP flush-mounted radio insert

Symbols on the Display

The information shown on the display may vary based on the Gira System 3000 app settings:

• 1, 2, 3: Favourite station active
• [Bluetooth Icon]: Bluetooth connection active
• [WLAN Icon]: WLAN connection active
• [Sleep Icon]: Sleep mode active
• [Alarm Icon]: Alarm clock active
• 12:03: Time display

Operating Surface Symbols

• >>: Press briefly: next station (radio) or track (Sonos, Bluetooth stream). Press and hold: previous station or track.
• 1, 2: Press briefly: call up favourite. Sonos: 1 - previous playlist, 2 - next playlist. Press and hold: save current station as favourite.
• [Power Icon]: Press briefly: switch on or off or set active alarm clock to snooze mode. Press and hold: switch off automatically after 30 minutes (activate sleep mode) or switch off active alarm clock when on, activate alarm clock when off.
• +, -: Increase or decrease volume.

Installation

[Warning Triangle] DANGER! Risk of death from electric shock. Disconnect the device. Cover any live parts.

Selecting the Installation Location

• Install indoors in an area protected against dripping and splashing water.
• If there are any electronic devices (e.g., ballasts) in the same installation unit or in the immediate vicinity, test on site and increase the spacing in the event of malfunctions.
• Recommended installation height: approximately 1.5 m.

Connecting Speakers (Optional)

The speaker impedance must not be less than 4 ohms!

1. Insert the speaker insert and lay the speaker insert connection cables in the device box of the IP flush-mounted radio insert.

Note: Do not remove the support ring seal for low-frequency reproduction. The support ring seal of the speaker insert acoustically decouples the insert from the front sound opening and improves low-frequency reproduction. Do not remove or damage the support ring seal, except for piercing it with the mounting screws.

2. Connect the speaker connection cables to the IP flush-mounted radio insert.

Mono Operation: For mono operation, connect the speaker insert to the left channel (L+/L-).

Connecting the Supply Voltage

3. Connect the supply voltage (230 V) to the L/N terminals of the IP flush-mounted radio insert.

Connecting Auxiliary Unit (Optional)

The auxiliary unit can be used to switch the flush-mounted radio simultaneously with the lighting, for example. After switching on, the radio may take up to 5-10 seconds to load.

4. Connect the switched phase of a switch to the auxiliary input (1) of the IP flush-mounted radio. Use the same phase for the auxiliary input and the power supply of the IP flush-mounted radio.

Installing Inserts and Cover Frames

5. Insert the IP flush-mounted radio insert into the flush-mounted device box.
6. Remove the protective cover plate from the speaker insert.
7. Position the cover frame and attach the speaker cover and operating top unit.

Start-up

After the initial start-up or a factory reset, a start-up wizard guides you through country and speaker selection. You can then choose to set it up via the app or without the app (using WPS). Setup as a Sonos operating device is only possible via the app.

Setup with the App

Requirement: Gira System 3000 app installed on a mobile device with Bluetooth and Android or iOS.

1. Press button 2 on the IP flush-mounted radio. Setup type "with the app" is selected.
2. Start the Gira System 3000 app and follow the instructions.
3. At the end of the setup, choose between WLAN Radio and Sonos Control. This selection is also available via the device parameters in the System 3000 App.

Setup without the App (using WPS)

1. Press button 1 on the IP flush-mounted radio. Setup type "WPS" is selected.
2. Activate the WPS function on the router. A WLAN connection is established.

Note: During start-up, the IP flush-mounted radio saves the first 20 stations it finds.

Operation on the Device

Only a light touch of the buttons is required for operation.

Switch On

1. Press the [Power Icon] button. The station or track last listened to will be played at the previously set volume.

Switch Off

1. Press the [Power Icon] button. The radio is switched off.

Activate Sleep Mode

1. Press the [Power Icon] button for more than 1 second. The IP flush-mounted radio will switch off automatically after 30 minutes.

Select Next Station or Track

1. Briefly press the >> button repeatedly until the desired station or track plays. Each press plays the next station or track in your favourites.

Select Previous Station or Track

1. Press and hold the >> button repeatedly until the desired station plays. The previous station or track from your favourites will be played.

Changing the Volume

1. Press the + or - buttons briefly to change the volume in increments.
2. Press and hold the + or - buttons to change the volume quickly. The volume is increased or decreased.

Play Favourite

1. Press button 1 or 2. For favourite 3, press buttons 1 and 2 briefly at the same time. The selected favourite is played.

Save Favourite

1. Press button 1 or 2, or for favourite 3, press buttons 1 and 2 for more than 1 second at the same time. The memory number is shown on the display once the favourite is saved.

Pairing the IP Flush-Mounted Radio with the Gira System 3000 App

Requirement: The IP flush-mounted radio must be switched off.

1. Hold down the + button for 4 seconds. The Bluetooth icon on the display will flash, indicating that it is searching for a connection.
2. Start the Gira System 3000 app and search for the device. Following a successful connection, the Bluetooth symbol will light up as long as the Gira System 3000 app is connected to the IP flush-mounted radio.

Resetting the IP Flush-Mounted Radio to Factory Settings

1. Press and hold buttons 2 and >> simultaneously. After 4 seconds, a countdown will appear on the display. At the end of the countdown, the device will be reset to factory settings.

Technical Data

Conformity

Gira Giersiepen GmbH & Co. KG hereby declares that the wireless system type, item no. 2320 .., conforms to Directive 2014/53/EU. The complete item number can be found on the device. The complete text of the EU declaration of conformity is available at the following web address: www.gira.de/konformitaet

Troubleshooting

Software Update for IP Flush-Mounted Radio

Once installed and connected, the IP flush-mounted radio searches for new software after 24 hours. This check occurs every 24 hours, even in standby mode. "FW Update" appears on the display. Press button 1 to start the update.

Encryption Protocol WPA3, WPA2

The IP flush-mounted radio can operate with both encryption protocols.

Encryption Protocol WPA3 and WPS

WPA3 does not support the WPS start-up process. To use WPS, briefly set the router's encryption protocol to WPA2. After start-up with WPS, the encryption protocol can be reset to WPA3. Alternatively, start-up with WPA3 and the System 3000 app is always possible.

Station List / Radio Favourites

• Following start-up, a station list with 20 radio favourites is created automatically.
• The order in the favourites list is based on data for the most popular radio stations in your country/region.
• The list of radio favourites cannot be extended or reduced. Radio stations cannot be deleted.

Station List Sorting

1. Navigate to the menu "Set device parameters", then "Manage radio stations". A list of 20 radio favourites is displayed.
2. Press the [Menu Icon] symbol on the left and move the selected radio station to the desired position.

You can select the first three favourite positions directly on the IP flush-mounted radio by pressing button 1, 2, or buttons 1 and 2 simultaneously. Press the >> button to call up the next radio station.

Add Stations, Change Radio Favourites

1. Navigate to the menu "Set device parameters", then "Find radio stations".
2. If necessary, change the country for the radio station search.
3. Scroll through the list or enter the radio station name.
4. Highlight the desired radio station once found. The selected radio station starts playing.
5. Tap "Next" at the top.
6. Swap the new radio station with a station from the favourites list by selecting the station to swap on the right.
7. Tap "Finished". The new radio station now appears in the radio favourites list.

Radio Station Interference

• Check location! Intermittent audio interference indicates poor network quality at the selected location. Change the location or use a WLAN repeater to improve network quality.
• If you select "Configure WLAN" in the System 3000 app, you will have no radio reception during the network search.
• In WLAN mesh networks, reception may be lost if the IP flush-mounted radio is relocated. In this case, you will need to reassign the WLAN network to the IP flush-mounted radio.

Bluetooth Streaming

For Bluetooth streaming, the system requires a second Bluetooth profile to be connected for audio transmission.

1. Go to the Bluetooth menu of your smartphone.
2. The Gira IP radio is displayed twice. For iOS, find the second Bluetooth profile under "Other devices".
3. Connect the second Bluetooth profile to your smartphone. The IP flush-mounted radio can now be selected as a speaker in the streaming app.

Warranty

The warranty is provided in accordance with statutory requirements via the retailer. Please hand over or send faulty devices postage paid, along with a description of the problem, to your sales representative (retailer / installation company / electronics retailer), who will forward the devices to the Gira Service Centre.