Gira IP Flush-Mounted Radio 2320

Safety

Electrical devices may only be installed and connected by a qualified electrician!

These instructions are an integral part of the product and must remain with the end customer.

Accessories

• Speaker for the IP flush-mounted radio (Item no. 2282)

Intended Use

• Playback of internet radio stations via connected speakers or speakers for mobile devices, operation of a Sonos music system.
• Possible to operate and programme using a mobile end device (smartphone or tablet) via Bluetooth with the Gira System 3000 app.
• Installation in DIN 49073 device box.

Device Components

The IP flush-mounted radio system consists of the following parts:

• IP flush-mounted radio operating top unit with display and operating surface.
• Speaker cover.
• Cover frame.
• Speaker insert.
• IP flush-mounted radio insert.

Connecting Speakers (Optional)

Important: The speaker impedance must not be less than 4 ohms!

1. Insert the speaker insert and lay the speaker insert connection cables in the device box of the IP flush-mounted radio insert.

Note on low-frequency reproduction: Do not remove the support ring seal for optimal low-frequency reproduction. The support ring seal acoustically decouples the insert from the front sound opening and improves bass response. Do not remove or damage the support ring seal, except for piercing it with mounting screws.

2. Connect the speaker connection cables to the IP flush-mounted radio insert:

Mono Operation: For mono operation, connect the speaker insert to the left channel (L+/L-).

Connecting the Supply Voltage

3. Connect the supply voltage (230 V) to the L/N terminals of the IP flush-mounted radio insert.

Connecting Auxiliary Unit (Optional)

The auxiliary unit can be used to switch the flush-mounted radio simultaneously with the lighting, for example. After switching on, the radio may take up to 5-10 seconds to load.

4. Connect the switched phase of a switch to the auxiliary input (1) of the IP flush-mounted radio. Important: Use the same phase for the auxiliary input and the power supply of the IP flush-mounted radio.

Installation

DANGER! Risk of death from electric shock. Disconnect the device. Cover any live parts.

Selecting the Installation Location:

• Install indoors in an area protected against dripping and splashing water.
• If electronic devices (e.g., ballasts) are in the same installation unit or nearby, test on site and increase spacing if malfunctions occur.
• Recommended installation height is approximately 1.5 meters.

Installing Inserts and Cover Frames

1. Insert the IP flush-mounted radio insert into the flush-mounted device box.
2. Remove the protective cover plate from the speaker insert.
3. Position the cover frame and attach the speaker cover and operating top unit.

Start-up

Upon initial start-up or after a factory reset, a start-up wizard will guide you through country and speaker selection. You can then choose to set up the device using the Gira System 3000 app or without the app via WPS. Setup as a Sonos operating device is only possible via the app.

Setup with the App

Requirement: The Gira System 3000 app must be installed on a mobile device with a Bluetooth interface (Android or iOS).

1. Press button 2 on the IP flush-mounted radio.
2. The setup type "with the app" is selected.
3. Start the Gira System 3000 app and follow the on-screen instructions.
4. At the end of the setup, you can choose between "WLAN Radio" and "Sonos Control". This selection can also be changed later via the device parameters in the System 3000 App.

Setup without the App (using WPS)

1. Press button 1 on the IP flush-mounted radio.
2. The setup type "WPS" is selected.
3. Activate the WPS function on your router.
4. A WLAN connection will be established.
5. During start-up, the IP flush-mounted radio saves the first 20 stations it finds.

Operation on the Device

Only a light touch of the buttons is required for operation.

Switch On

1. Press the △ button.
2. When the device is switched on, the last played station or track will resume at the previously set volume.

Switch Off

1. Press the △ button.
2. The radio will switch off.

Activate Sleep Mode

1. Press and hold the △ button for more than 1 second.
2. The IP flush-mounted radio will automatically switch off after 30 minutes.

Select Next Station or Track

1. Briefly press the △ button repeatedly until the desired station or track is playing.
2. Each press advances to the next station or track in your favorites list.

Select Previous Station or Track

1. Press and hold the △ button for more than 1 second repeatedly until the desired station is playing.
2. This cycles through previous stations or tracks from your favorites.

Changing the Volume

1. Briefly press the + or - buttons to adjust the volume in small increments.
2. Press and hold the + or - buttons to change the volume rapidly.

Play Favorite

1. Briefly press button 1 or button 2. For favorite 3, press buttons 1 and 2 simultaneously.
2. The selected favorite station will play.

Save Favorite

1. Press and hold button 1 or button 2 for more than 1 second. For favorite 3, press and hold buttons 1 and 2 simultaneously for more than 1 second.
2. Once the favorite is saved, the memory number will be displayed.

Pairing the IP Flush-Mounted Radio with the Gira System 3000 App

Requirement: The IP flush-mounted radio must be switched off.

1. Hold down the + button for 4 seconds.
2. The Bluetooth icon on the display will flash, indicating it is searching for a connection.
3. Start the Gira System 3000 app and search for the device.
4. Upon successful connection, the Bluetooth symbol will remain lit as long as the Gira System 3000 app is connected to the IP flush-mounted radio.

Resetting the IP Flush-Mounted Radio to Factory Settings

1. Press and hold button 2 and the △ button simultaneously.
2. After 4 seconds, a countdown will appear on the IP flush-mounted radio's display. At the end of the countdown, the device will be reset to factory settings.

Technical Data

Conformity

Gira Giersiepen GmbH & Co. KG hereby declares that the wireless system type, item no. 2320, conforms to Directive 2014/53/EU. The complete item number can be found on the device. The complete text of the EU declaration of conformity is available at the following web address: www.gira.de/konformitaet

Warranty

The warranty is provided in accordance with the statutory requirements via the retailer. Please hand over or send faulty devices postage paid, along with a description of the problem, to your sales representative (retailer / installation company / electronics retailer), who will forward the devices to the Gira Service Centre.