FCC Radio Test Report

Summary of Test Result

Note:

• For host device, Effective Radiated Power and Equivalent Isotropic Radiated Power are verified and complies with the limit in this test report.
• For host device, the Conducted Output Power is no difference after compared to module (Model: EM160R-GL).
• The measurement evaluation of RSE is based on the module report measurement results, with the worst case from module report. The measurement results of RSE are included in the SPT report: FG3O1203A.

General Description

1.1 Product Feature of Equipment Under Test

Remark:

• The above EUT's information was declared by manufacturer.
• Equipment: Quectel EM160R-GL tested inside of Lenovo Notebook Computer.

The product was installed into Notebook Computer (Brand Name: Lenovo, Model Name: TP00151A) during test, and the host information was recorded in the following table.

Remark: The above EUT's information was declared by manufacturer. Please refer to Disclaimer in report summary.

1.2 Product Specification of Equipment Under Test

1.3 Modification of EUT

No modifications made to the EUT during the testing.

1.4 Testing Location

FCC Designation No.: TW1190

1.5 Applicable Standards

According to the specifications declared by the manufacturer, the EUT must comply with the requirements of the following standards:

• ANSI C63.26-2015
• ANSI/TIA-603-E
• FCC 47 CFR Part 2, 22(H), 24(E), 27(L)
• FCC KDB 971168 D01 Power Meas. License Digital Systems v03r01
• FCC KDB 412172 D01 Determining ERP and EIRP v01r01

Remark:

1. All the test items were validated and recorded in accordance with the standards without any modification during the testing.
2. The TAF code is not including all the FCC KDB listed without accreditation.

Test Configuration of Equipment Under Test

2.1 Test Mode

Antenna port conducted and radiated test items were performed according to KDB 971168 D01 Power Meas. License Digital Systems v03r01 with maximum output power. Test modes are chosen to be reported as the worst case configuration below:

2.2 Frequency List of Low/Middle/High Channels

Conducted Test Result

3.1 Measuring Instruments

Please refer to the measuring equipment list in this test report.

3.1.1 Test Setup

A diagram shows a system simulator connected to the Equipment Under Test (EUT).

3.1.2 Conducted Output Power

Please refer to Appendix A.

3.2 Conducted Output Power and ERP/EIRP

3.2.1 Description of the Conducted Output Power and ERP/EIRP

A system simulator was used to establish communication with the EUT. Its parameters were set to enforce EUT transmitting at the maximum power. The measured power in the radio frequency on the transmitter output terminals shall be reported.

• The ERP of mobile transmitters must not exceed 7 Watts for WCDMA Band V
• The EIRP of mobile transmitters must not exceed 2 Watts for WCDMA Band II
• The EIRP of mobile transmitters must not exceed 1 Watts for WCDMA Band IV

According to KDB 412172 D01 Power Approach,

EIRP = PT + GT – LC, ERP = EIRP -2.15, where

• PT = transmitter output power in dBm
• GT = gain of the transmitting antenna in dBi
• Lc = signal attenuation in the connecting cable between the transmitter and antenna in dB

3.2.2 Test Procedures

1. The transmitter output port is connected to the system simulator.
2. Set EUT at maximum power through system simulator.
3. Select the lowest, middle, and the highest channels for each band and different modulation.
4. Measure the maximum burst average power for GSM and maximum average power for other modulation signal.

List of Measuring Equipment

Appendix A. Test Results of Conducted Test

Conducted Output Power(Average power) & ERP / EIRP

WCDMA Band V Maximum Average Power [dBm] (GT - LC = -0.35 dB)

WCDMA Band II Maximum Average Power [dBm] (GT - LC = 0.83 dB)

WCDMA Band IV Maximum Average Power [dBm] (GT - LC = 1.16 dB)