Litokam Smart Video Doorbell

1. Doorbell Overview

The Litokam Smart Video Doorbell comes with various components and accessories to facilitate its setup and operation.

Front View Components:

• Infrared Light
• MIC (Microphone)
• Photosensitive Sensor
• PIR (Passive Infrared) Sensor
• Doorbell Button
• Work Indicator

Back View Components:

• Restart Button ?
• AC Power Connector
• Type C Power Button ?
• TF Card Slot ?

Included Accessories:

• Speaker ?
• Chime ?
• User's Manual ?
• Video Doorbell ?
• Ring Button ?
• Doorbell disassembly needle ?
• USB Power cord ?
• Wire jumper 〰️
• AC Power extension cord ⚡
• Screw Hole Positioning Card ?
• Double Sided Tape ?
• Screw pack ?

Doorbell Indicator Status

Introduction to Doorbell Buttons

2. Doorbell Network Settings

Note: After receiving the doorbell, please use the included charging cable to fully charge the doorbell.

The doorbell battery life can vary. Normally, it records 10 events per day for 20 seconds each. Under these conditions, a fully charged doorbell can last up to 6 months.

APP Download and Account Registration:

Scan the QR code ? to download and install the "Littlelf Smart" APP. Register an account using your email address. The app is available on Google Play and the App Store.

Initial Setup:

1. Connect your mobile phone to a 2.4GHz Wi-Fi network ?.
2. After the doorbell is fully charged, long press the Power Button ? for 3 seconds to turn it on. The LED indicator will slowly flash blue, and you will hear a "Device Power on" prompt.
3. When the doorbell plays the "Ready to connect" prompt, you can start configuring the network. If this prompt is not heard, long press the Power Button ? for 5 seconds to restore factory settings.

A. Quickly Configure Network for the Doorbell

1. Log in to the "Littlelf Smart" APP. Turn on Bluetooth ? on your mobile phone and grant the APP necessary permissions.
2. Click the "Add" button in the dialog box. If the dialog box does not appear, click the "+" icon or "Add Device" button on the home page. The doorbell will be searched. Click the "+" icon next to the doorbell to add it.
3. Enter your Wi-Fi password (the doorbell only supports 2.4GHz) and click "Next".
4. Wait for the doorbell to automatically complete network configuration.
5. Click "Done" once the configuration is complete.

B. Configure Doorbell Network using QR Code

1. On the "Littlelf Smart" APP home page, click the "+" or "Add Device" button.
2. Select the doorbell type "D1".
3. Confirm the doorbell indicator status and click "Next".
4. Enter your Wi-Fi password and click "Next".
5. Aim the QR code generated on your phone screen at the doorbell camera from a distance of 15-20 cm. After hearing "Scan code success", click "Hear the beep".
6. Wait for the doorbell to automatically complete network configuration and click "Done".

Chime Configuration

1. In the device list interface, click the doorbell "D1" to access the live broadcast interface. Select Settings ⚙️ / Chime Settings / Connect Chime. Select "Connect" in the dialog box.
2. Plug the Chime ? into a power socket. It will turn on with a start bell, and its indicator will flash white. Select "Hear the Chime Ring and indicator will flash white" and click "Next". If the Chime's indicator does not flash white, long press the Ring Button ? on the Chime for 5 seconds until it rings.
3. Press the "Doorbell" button on the doorbell. When you hear the Chime ring, select "Hear the Chime Ring" and click "Send Pairing Code".
4. Press the "Doorbell" button on the doorbell again to confirm if the Chime rings. If it rings, click "Done" to complete pairing. If the Chime does not ring, click "Chime does not ring" and repeat the pairing process as prompted.

Doorbell setting completed.

3. Storage Methods

There are two options for video storage:

A. Cloud Storage ☁️

Subscribe to the cloud storage package. After enabling this function, the doorbell will automatically save videos to the cloud, allowing you to view recordings anytime, anywhere.

B. SD Card Storage (Local Storage) ?

An SD Card is required for local storage. Insert the SD Card into the designated slot as shown in the figure. Once the doorbell identifies the SD Card, recorded videos will be stored on it.

Diagram Description: Shows the microSD card slot on the doorbell.

4. Doorbell Mounting

Factors to Consider:

• Check if existing holes in walls or door frames can be reused.
• If mounting close to the wall, ensure the wall side does not appear in the monitoring field of view to avoid blurriness in night vision mode due to infrared light refraction.
• It is recommended to install the doorbell at a height of 48" (1.2m) from the ground to reduce monitoring blind spots.
• For package monitoring, it is recommended to place the package rack 0.5 meters away from the wall. (Package detection function may require an additional fee.)

Diagram Description: Illustrates recommended installation height (1.76m / 5'9" person) and detection range (0.3m / 12" from ground, 0.5m from wall).

Method 1: Battery-Powered Installation Steps

1) Install Doorbell Bracket ?

A. Mounting on Wooden Surface (Door Frame): No pre-drilling is required. Use a screwdriver ? to tighten the screws to secure the bracket to the mounting spot. (Use the doorbell disassembly needle ? to remove the bracket from the unit.)

Tools Required: Screwdriver ?, Screw (included) ?, Doorbell disassembly needle ?, Doorbell bracket ?.

Diagram Description: Shows the doorbell bracket being attached to a wall with screws.

B. Mounting on Hard Surface (Brick, Concrete, Stucco):

1. Paste the positioning card ? to the doorbell mounting spot.
2. Use a 15/64" (6 mm) drill bit ड्रिल to drill holes according to the screw holes on the positioning card.
3. Insert anchors ⚓ into the holes, then use a screwdriver ? to tighten the screws to secure the doorbell bracket to the mounting spot.

Tools Required: Electric drill ड्रिल, 6mm drill bit ड्रिल, Mounting bracket ?, Screw pack ?.

Diagram Description: Shows drilling into a brick wall, inserting anchors, and attaching the bracket.

2) Mount the Doorbell on the Doorbell Bracket

Align the bottom of the doorbell with the fixed position on the bracket and press the top until it clicks into place.

Diagram Description: Shows three steps of aligning and attaching the doorbell to the bracket.

Note: Before mounting, please complete the network configuration for the doorbell and ensure it is powered on.

3) Detach the Doorbell from Doorbell Bracket

If you need to remove or charge the doorbell, insert the doorbell disassembly needle ? into the removal hole above the doorbell and press down firmly. The doorbell will automatically pop out of the bracket.

Tools Required: Doorbell disassembly needle ?.

Diagram Description: Shows the disassembly needle being inserted to release the doorbell.

Method 2: Installation Steps for Powering a Doorbell Using Existing Doorbell Wires

1) Check Whether Existing Doorbell Wires Are Working Properly

Press the doorbell button of the existing doorbell to check if it is working. If it does not ring, the power wires may be defective. Install the new doorbell using the battery-powered method or consult an electrician. If it rings properly, shut off the power to the existing doorbell at the circuit breaker ⚡.

Diagram Description: Shows a hand turning off a circuit breaker switch.

Note: The required voltage for the doorbell is 8-24V AC. Please confirm your existing doorbell wires meet this requirement. If your existing doorbell has an 8V power supply, use the provided "jumper cable" 〰️ to connect the two terminals in your existing doorbell chime.

Warning: Be careful when handling wires during installation. If you are not comfortable, have an electrician perform the installation.

2) Detach the Existing Doorbell

Use a screwdriver ? to detach the existing doorbell. Pay attention to the power wires on the back. Remove the power wires using a screwdriver and check if they are damaged or aging.

Tools Required: Screwdriver ?.

Diagram Description: Shows three stages of detaching an old doorbell from the wall.

3) Install Doorbell Bracket

(Refer to Method 1, Step 1 for bracket installation instructions.)

4) Connect the Doorbell Wires ?

Loosen the screw on the AC power port on the back of the doorbell. Connect the wall wire to the power port and tighten the screw. The doorbell AC power terminals do not distinguish between positive and negative poles and can be connected in any order.

Notes:

• The AC power terminals do not distinguish between positive and negative poles and can be connected in any order.
• To prevent short-circuits, ensure the positive and negative poles of the wires are not touching each other.
• If the wires are too short, use the provided extension wires and wire nuts to make them longer. Use electrical tape if there is no space for wire nuts.

Tools Required: Screwdriver ?, Video doorbell ?, AC Power extension cord ⚡.

Diagram Description: Shows connecting wires to the back of the doorbell.

5) Mount the Doorbell on the Doorbell Bracket

(Refer to Method 1, Step 2 for mounting instructions.)

Diagram Description: Shows alignment and attachment to bracket.

6) Turn on the Doorbell Power Switch on the Circuit Breaker

Turn the circuit breaker ⚡ ON.

Diagram Description: Shows turning the circuit breaker ON.

Through the Littlelf Smart APP, check the doorbell monitoring screen to confirm if the doorbell is charging. If it is displayed as charging, the installation is complete. If not, check the power wires.

5. Common Problems

Q1: The doorbell doesn't turn on

1. Long press the Power Button ? for 3 seconds and ensure it is pressed.
2. Use the Type-C USB cable ? to charge the doorbell for about 3 minutes. Check if the LED indicator is green. Solid green means the battery is insufficient. If the LED does not light up, try a different Type-C USB cable or charger (must support 5V/1.5A).
3. Bring the doorbell indoors before turning it on to avoid issues due to low outdoor temperatures. The operating temperature is -4°F to 122°F (-20°C to 50°C).

Q2: Doorbell network configuration failed.

If the doorbell indicator flashes blue and sounds "Ready to connect" after turning on, network configuration is usually normal. If the indicator flashes differently, troubleshoot as follows:

1. Restore factory settings: Long press the Power Button ? for 5 seconds when powered on.
2. Unplug the USB charging cable ?. The indicator will flash green when charging.
3. Check if the router password is correct (Wi-Fi password, not APP account password).
4. Verify your router's Wi-Fi signal is 2.4GHz. If your router uses a shared account for 2.4GHz and 5GHz, configure them separately.
5. Ensure the Wi-Fi connected to your phone is 2.4GHz.

Q3: Littlelf Smart APP home page shows doorbell offline.

1. Adjust the router's position to ensure a strong and stable Wi-Fi signal ? at the doorbell's location.
2. Confirm that the router's Wi-Fi signal can access the network normally.

6. Technical Specifications

Doorbell

• Operating Temperature: -20°C to 50°C
• Operating Humidity: 10%-95% (No condensation)
• Note: Maximum normal operating temperature is +50°C (excluding battery charging). Maximum battery charger temperature is 45°C.
• Frequency Range: 2.412-2.472 GHz
• RF Output Power: 17.5 dBm
• Power: 8-24V~50/60Hz 50mA or 5V 1A

Chime

• Operating Temperature: -10°C to 45°C
• Operating Humidity: <90% at 40°C
• Communication: RF 433MHz
• Power: 100-240V~50/60Hz
• Symbol Meanings: AC (alternating current), Indoor use, Bathroom excluded, Class II product (Double Insulated - No earth required).

7. Notification of Compliance

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. However, interference is not guaranteed in all installations. If interference occurs, try one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC RF Exposure Warning Statements

This equipment complies with FCC radiation exposure limits for an uncontrolled environment. It shall be installed and operated with a minimum distance of 20 cm between the radiator and the body.

CE EU Declaration of Conformity

Litokam declares that the doorbell complies with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Disposal: This product must not be disposed of as normal household waste, in accordance with EU directive (WEEE- 2012/19/EU). Instead, it should be returned to the point of sale or a municipal recycling collection point. The device can be used with a separation distance of 20 cm to the human body.

ISED Statements

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation.

8. Litokam Customer Care

For additional support, please refer to the following resources:

• FAQs and Guide Video: Available on the Littlelf Smart app or official website. (Scan the QR code ? for quick access)
• Online Customer Service: Available via app, telephone, and website during the following hours: PT 08:00-10:00 / 17:30-20:00 / 21:30-08:00
• Littlelf Smart APP Live chat
• Website: ? www.litokam.com
• Tel: ? US&Canada Toll Free PT 1 (866)722-6296 (Mon-Sun: 11:00 AM - 6:30 PM)
• Email: ✉️ support@litokam.com

Follow us on social media: @Litokam ? f ▶️

Warranty Terms:

• 30-day return policy and 12-month limited warranty.
• Lifetime professional tech support provided by Litokam.