MOTION ACTIVATED LED SECURITY LIGHT WITH REMOTE SENSOR

Specifications

Voltage: 120 VAC ~ 60Hz
Wattage: 20 W LED
Lumen: 2200LM
240-degree detection up to 50ft
RF Remote Sensor with 100ft Range
Color temperature: 4000K
Weatherproof: IP65
Suitable for Wall or Eave mount

Package Includes

1x Light fixture
1x Motion Sensor
1x Mounting bracket (for sensor)
4x Mounting screws (2 sizes included)
1x Mounting bracket
2x Mounting screws (for sensor)
1x Mounting bolt (pre-installed in light fixture)
1x Rubber Screw Hole Plug
2x Wall anchors (for sensor)

Safety Information

WARNING: This light fixture requires 120-volts AC. Some codes require installation by a qualified electrician.
WARNING: Turn the power OFF at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is OFF at the light fixture.
WARNING: Risk of fire. Do not aim the light fixture heads at a combustible surface within 3 ft. (1 m).
CAUTION: Burn hazard. Allow the light fixture to cool before touching.
CAUTION: Do not cut any wires with factory installed wire connectors or remove the wire connectors.
NOTICE: Do not connect this light fixture to a dimmer switch or timer.
WARNING: Do not mix old and new batteries.
WARNING: Do not mix alkaline, standard, or rechargeable batteries.

Tools Required (Not Included)

#	Tool
1	Phillips screwdriver
2	Flathead screwdriver
3	Pliers
4	Wire strippers/cutters
5	Circuit tester
6	Work gloves
7	Electrical tape
8	Silicone sealant
9	Ladder
10	Safety goggles
11	Drill
12	3/16" (5mm) Drill bit

Installation

1. Determining the Mounting Location

Determine the mounting location. Position the light fixture heads in the general direction of the desired light coverage. Options include Wall Mount and Eave Mount.

2. Mounting the Light Fixture

Turn OFF the main power supply before installation to avoid electric shock. Secure the mounting bracket (B) to the junction box using the mounting screws (A) that best fit the junction box.

3. Wiring the Light Fixture

Connect the light fixture wires to the junction box wires (D) with the easy connector (C). Ensure wiring is in accordance with the National Electrical Code. Connect white wire to white wire and black wire to black wire.

4. Fixing the Light Fixture

Secure the light fixture to the mounting bracket using the mounting bolt (E). Cover the mounting bolt (E) with the rubber screw hole plug (F). Ensure all wires are inside the junction box before attaching the fixture backplate.

5. Caulking Around the Light Fixture

CAUTION: Failure to completely caulk around the light fixture's mounting plate could result in water seepage into the light fixture and/or junction box. Caulk around the light fixture and mounting surface with silicone sealant (not included).

Sensor Installation

1. Remove the back cover

Remove the back cover (F) from the sensor unit.

2. Unscrew and remove the battery cover screw

Unscrew the battery cover screw (G) and remove the battery cover.

3. Install batteries

Insert two AA batteries (not included) into the battery box. Replace the battery cover onto the sensor.

4. Mark and drill mounting holes

Use the back cover (F) to mark the position of screw holes on the mounting surface. Drill the wall to a depth of approximately 60 mm (2.36 inches) and fit the wall anchors (H). Then, fix the back cover (G) to the mounting surface with screws.

5. Mount the back cover

Mount the back cover (F) onto the wall.

6. Mount the sensor

Mount the sensor onto the back cover.

7. Connect the sensor and light fixture

The sensor is factory pre-set to connect to the included light fixture. Once batteries are installed and the light is powered, motion detection should function. To pair or reset: Hold the RESET button on the sensor; the indicator LED will flash 5 times, then flash every 1 second, entering distribution mode. Keep the sensor near the light fixture. Unconnected lights will turn ON for 3 minutes. After distribution, the light turns OFF. Press RESET again for 1 second to exit distribution mode and enter auto mode.

8. ON-TIME Feature

This feature allows selection of the time after which the light turns OFF when no motion is detected. The light remains ON as long as motion is detected.

9. TEST Function

The light will turn ON for approximately 5 seconds, regardless of day or night. The sensitivity setting determines the maximum distance the PIR sensor can be triggered by movement.

Resetting the Sensor

If the sensor becomes inactivated, hold the RESET button after connecting batteries. After the indicator light flashes 5 times, release and connect the light to 120V AC power. The newly connected light will initially be ON and turn OFF after successful connection. Press RESET again after the light turns OFF to finalize the network connection.

Care and Cleaning

To maintain the original appearance, clean only with clear water and a soft, damp cloth. Do not use paints, solvents, or other chemicals, as they may cause premature deterioration of the finish. This is not a defect and is not covered by warranty. Do not spray with a hose or power washer.

Troubleshooting Guide

Problem	Possible Cause	Solution
Light will not come ON.	1. Light switch is OFF. 2. Fuse is blown or circuit breaker is OFF. 3. Daylight turn-off (photocell) is active. 4. Incorrect circuit wiring. 5. Motion sensor aimed incorrectly. 6. Motion sensor not connected. 7. Motion sensor batteries not charged or inserted incorrectly.	1. Turn light switch ON. 2. Replace fuse or turn circuit breaker ON. 3. Recheck after dark. 4. Verify wiring. 5. Re-aim sensor. 6. Ensure sensor is connected and functioning. 7. Check battery charge and insertion.
Light comes ON during the day.	1. Motion sensor installed in a dark location. 2. "ON-TIME" dial set to "TEST".	1. Light fixture operates normally. 2. Turn "ON-TIME" dial to 1, 5, or 20 minute setting.
Light comes ON for no apparent reason.	1. Motion sensor detecting small animals, traffic, or heat sources. 2. "Sensitivity SENS" dial set too high. 3. Light wired through a dimmer or timer.	1. Light fixture operates normally. 2. Decrease "Sensitivity SENS" setting. 3. Replace dimmer/timer with standard ON/OFF switch.
Light turns OFF too late in Dusk-to-Dawn setting.	1. Sensor installed in a dark location.	1. Relocate the sensor.
Light stays ON continuously.	1. Motion sensor in "TEST" mode. 2. Light wired through a dimmer or timer. 3. Light on circuit with motors, transformers, or fluorescent bulbs.	1. Switch sensor to auto mode. 2. Replace dimmer/timer with standard ON/OFF switch. 3. Install on a circuit without motors, transformers, or fluorescent bulbs.

Compliance Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.

ISED Warning: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device has been evaluated to meet general RF exposure requirement. The distance between user and products should be no less than 20cm. CAN ICES-005 (B)/NMB-005 (B)

FCC Responsible party: Globe Electric, 2264 East 6th Street, San Bernardino, CA 92410, www.globe-electric.com