Moen Single Handle Kitchen Faucet with PowerBoost™ Pro

Contact Information

For Installation Help, Missing or Replacement Parts:

• USA: 1-800-BUY-MOEN (1-800-289-6636) | www.moen.com
• Canada: 1-800-465-6130 | www.moen.ca
• Mexico: 01152 (800) 718-4345 | www.moen.com.mx

Helpful Tools

For safety and ease of faucet replacement, Moen recommends the use of these helpful tools:

• Adjustable Pliers
• Adjustable Wrench
• Flathead Screwdriver
• Phillips Screwdriver
• Safety Glasses
• Sealant
• Tape Measure
• Thread Seal Tape

Parts List

Diagram of Faucet Components:

• A. Faucet Body
• B. Escutcheon
• C. Deck Gasket
• D. Installation Tool
• E. Support Bracket
• F. Mounting Bracket Nut
• G. Spray Wand
• H. Hose Weight
• I. Toggle Button
• J. Pulldown Hose
• J1. Pulldown Hose Weight Indicator Mark
• K. Outlet Hose
• L. Supply Hose Hot
• M. Supply Hose Cold
• N. Deck Plate (optional)
• O. Deck Plate Gasket (optional)
• P. Coil Spring

Installation Instructions

Step 1A: Single Hole Applications

1. Place Escutcheon (B) and Deck Gasket (C) onto the base of the Faucet Body (A) and place into the sink hole. Note: Install with handle on the right side only.

Step 1B: Applications with Deck Plate

1. Place Deck Plate Gasket (O) onto Deck Plate (N).

2. Firmly snap Deck Plate Gasket (O) onto Deck Plate (N).

3. Flip Deck Plate (N) over and place onto the mounting surface, then install Faucet Body (A) in the hole on the sink.

Step 2: Securing the Faucet Body

1. Slide Mounting Washer (E) up onto the Faucet Body (A) under the sink.

2. Install Mounting Nut (F).

Step 3: Tightening the Mounting Nut

1. Hand tighten Mounting Nut (F) with Installation Tool (D).

2. Use a screwdriver through the hole in the Installation Tool (D) to tighten firmly.

Step 4: Connecting Flexible Lines

1. Attach flexible lines (L and M) to the shutoff valves.

2. Tighten with a wrench until secure.

Step 5: Attaching the Spray Wand

1. Remove the Wand Cap from the Spray Wand (G).

2. Attach the Spray Wand (G) to the Pulldown Hose (J) and finger tighten.

Step 6: Feeding the Pulldown Hose

1. Insert the small end of the Pulldown Hose (J) into the spout and feed it through the Coil Spring (P).

Step 7: Installing the Pulldown Hose and Spring

1. Install the Pulldown Hose (J) and Spring (P) through the Faucet Body (A).

Step 8: Connecting the Pulldown Hose to the Outlet Hose

1. Remove and discard the plastic cap from the end of the Pulldown Hose (J).

2. Insert the hose into the Outlet Hose (K).

3. Push until a "click" is heard. Tug downward to test engagement.

Step 9: Attaching the Hose Weight

IMPORTANT: Locate the Hose Weight Locator Mark (J1) on the Pulldown Hose (J). Install the Hose Weight (H) just above the loop curvature in the hose, on the same side of the hose as the locator mark. Adjustable pliers may be useful to securely clamp the Hose Weight (H).

Step 10: Water Supply Connection

1. Turn on the Hot (L) and Cold (M) water supply.

Step 11: Flushing the Faucet

1. Hold the Pulldown Hose (J) and turn on the Faucet (A). Allow water to run for 15 seconds.

2. Turn off the faucet (A).

Step 12: Spray Wand Functionality

The spray wand offers different flow modes:

• Low Flow Mode: For a gentle stream.
• Boost Flow Mode: For a more powerful spray.
• Stream Mode: A focused stream of water.
• Spray Mode: A wider spray pattern.

Press the button on the spray wand to change between modes. Features may vary by model.

Step 13: Flushing the Spray Wand

1. Unscrew the Pulldown Hose (J) from the Spray Wand (G) and remove the screen and o-ring.

Step 14: Rinsing the Screen

1. Rinse the debris from the screen.

Step 15: Reassembling the Spray Wand

1. Reinstall the screen and o-ring as shown. Thread the Pulldown Hose (J) onto the Spray Wand (G) and tighten. Tighten the Pulldown Hose (J) until it is flush with the Spray Wand (G). Do not overtighten.

Step 16: Final Check

1. Re-check the water flow.

1. Finished installation.

Important Considerations

For optimal performance, maintain an 8"x8" (203mm x 203mm) clear area for the hose and weight to travel, free of any moveable items like bottles or cleaning supplies. If obstructions like pipes or fixtures interfere, consider repositioning the weight higher on the hose. Periodically check this area for obstructions.

To further enhance performance, Moen offers the 159060 Hose Guide to isolate the hose from plumbing lines and other items under the sink. Contact Moen at 1-800-289-6636 or visit www.moen.com to order part #159060.

Warranty Information

Moen offers a Limited Lifetime Warranty to the original consumer purchaser for their home, covering defects in material and workmanship for as long as they own their home. For other purchasers, the warranty is for 5 years from the original date of purchase. Moen will provide free replacement parts for any leaks or drips during the warranty period. This warranty is subject to certain exclusions, including damage from installation errors, product abuse, misuse, or use of abrasive cleaners. Moen is not responsible for labor charges or incidental/consequential damages. Some regions may have different legal rights.

Moen Incorporated
25300 Al Moen Drive
North Olmsted, Ohio 44070-8022
U.S.A.

Moen de Mexico, S.A. de C.V.
Carretera Saltillo-Monterrey KM 14.7
Ramos Arizpe, Coahuila
Mexico 25900

Moen Inc.
2816 Bristol Circle
Oakville, Ontario L6H 5S7
Canada