Teka HLB & HLB P Ovens: User Manual and Operation Guide

Oven Description

The oven features a modern design with an internal cavity, control panel, and various components.

Components:

• 1 Panel sterowania: Control panel.
• 2 Blokada drzwiczek: Door lock (pyrolytic models only).
• 3 Grzałka grilla: Grill heating element.
• 4 Wsporniki boczne: Side supports for racks.
• 5 Ruszt: Oven rack.
• 6 Blacha do pieczenia: Baking tray.
• 7 Zawias: Door hinge.
• 8 Szyba wewnętrzna: Inner oven door glass.
• 9 Odprowadzenie oparów: Steam outlet.
• 10 Mocowanie do szafki: Cabinet mounting point.
• 11 Oświetlenie: Oven light.
• 12 Panel tylny: Rear panel.
• 13 Wentylator nawiewu: Convection fan.
• 14 Uszczelka piekarnika: Oven door seal.
• 15 Drzwiczki: Oven door.

Control Panel

Modele HLB

The control panel for HLB models features:

• 1 Pokrętło wyboru funkcji: Function selection knob.
• 2 Wyświetlacz zegara/elektroniczny programator: Clock/electronic programmer display.
• 3 Pokrętło wyboru temperatury: Temperature selection knob.

Modele pirolityczne HLB P

The control panel for pyrolytic HLB P models features:

• 1 Pokrętło wyboru funkcji: Function selection knob.
• 2 Wyświetlacz zegara/elektroniczny programator / Ustawiona temperatura: Clock/electronic programmer display / Set temperature.
• 3 Pokrętło wyboru temperatury: Temperature selection knob.

Function Selection Symbols

The symbols on the function selection knob vary by model series:

• Modele HLB 822, HLB 830: [Symbols for various functions like Eco, defrost, etc.]
• Modele HLB 840, HLB 841, HLB 850, HLB 8400: [Symbols for various functions like Eco, defrost, etc.]
• Modele HLB 822 P, HLB 830 P: [Symbols for various functions like Eco, defrost, etc.]
• Modele HLB 840 P, HLB 8400 P: [Symbols for various functions like Eco, defrost, etc.]

Note: Specific symbols are depicted in the original PDF and represent functions such as Eco mode, defrosting, Hydroclean, and rapid heating.

Heating Functions

The oven offers various heating functions:

• POZYCJA WYŁĄCZENIA: Off position.
• GRZAŁKA GÓRNA + GRZAŁKA DOLNA: Top + bottom heating element.
• GRILL: Grill function.
• MAXIGRILL: Maximum grill function.
• GRZAŁKA DOLNA: Bottom heating element.
• MAXIGRILL + NAWIEW: Maximum grill with fan.
• GRZAŁKI GÓRNA I DOLNA + NAWIEW: Top and bottom heating elements with fan.
• TERMOOBIEG (NAWIEW + GRZAŁKA PIERŚCIENIOWA): Convection (fan + ring heating element).
• TERMOOBIEG + GRZAŁKA DOLNA (PIZZA): Convection + bottom heating element (Pizza function).
• ECO: Eco mode.
• ROZMRAŻANIE: Defrosting.
• HYDROCLEAN: Hydroclean function for cleaning.
• PIROLIZA: Pyrolytic cleaning function.
• SZYBKIE NAGRZEWANIE: Rapid heating.

Detailed descriptions of each heating function can be found in the included baking guide.

Electronic Programmer and Display

The display shows time and programming information.

Buttons:

• OK & +: Used for setting the clock and operating the electronic programmer.
• OK: In models with electronic temperature regulation, pressing this button displays the current baking temperature.

Symbols:

• ALARM [ ( ) ]: Indicates the electronic programmer is active. A beep sounds when the programmed time elapses. The oven does not switch off automatically. Can be used during baking.
• PROGRAMOWANIE [ →→ ]: Indicates that a time function (baking time, end time, or total time) has been set.
• Czas pieczenia [ → ]: Allows programming the baking duration, after which the oven will switch off automatically.
• Czas zakończenia pieczenia [ →l ]: Allows programming the end time of baking, after which the oven will switch off automatically.
• Czas pieczenia i czas zakończenia pieczenia: Allows programming both duration and end time. The oven will start automatically at the programmed time and run for the set baking time. It will switch off automatically at the programmed end time.
• BLOKADA URUCHOMIENIA [ ]: Locks the electronic programmer buttons to prevent children from operating the device.

Other Functions:

• TERMOSTAT: Indicates the oven is heating up and transferring heat to the food.
• HYDROCLEAN: Illuminates during the Teka Hydroclean® cleaning cycle.
• PIROLIZA: Illuminates during pyrolytic cleaning (pyrolytic models only).
• BLOKADA DRZWICZEK: Door lock (pyrolytic models only). Indicates the door is manually or automatically locked during pyrolytic cleaning.

Setting the Time

To set the clock:

• Set function and temperature knobs to the [off-position] (o).
• After connecting the oven, "12:00" will flash on the display.
• Touch the [touch-sensor] or [plus-button] to set hours, then minutes. A double beep confirms the setting.
• To change the time, press [touch-sensor] or [plus-button] until the current time flashes. Then follow the previous steps.

Note: In night mode (00:00 - 06:00), the display backlight is less intense.

Oven Operation

Operation Without Electronic Programmer

Once the clock is set, the oven is ready for use. Select a heating function and set the temperature.

• During baking, the [thermostat-symbol] will be illuminated, indicating the oven is heating. It will turn off when the set temperature is reached.
• Turn the selection knobs to the [off-position] (o) to turn off the oven.

Information:

• In models with electronic temperature control, the set temperature appears on the clock display after turning the knob. The current time is displayed automatically after setting the temperature.
• To view the temperature during baking, press the [ok-button]. To change the temperature, turn the temperature knob.
• After baking starts, the display shows the elapsed baking time.

Operation With Electronic Programmer

Programming the Alarm

1. Touch the [touch-sensor] or [plus-button] until the [alarm-symbol] [ ( ) ] flashes. Press [ok-button]. The display will show "00:00".
2. Set the alarm duration by pressing the [touch-sensor] or [plus-button]. A double beep confirms. The countdown starts, and the [alarm-symbol] [ ( ) ] will flash slowly.
3. After the programmed time, a beep will sound, and the [alarm-symbol] [ ( ) ] will flash rapidly.

Programming Baking Time

1. Touch the [touch-sensor] or [plus-button] until the [baking-time-symbol] [ → ] flashes. Press [ok-button]. The display will show "00:00".
2. Set the baking time by pressing the [touch-sensor] or [plus-button]. A double beep confirms. The countdown starts, and the [baking-time-symbol] [ → ] will flash slowly.
3. Select the heating function and set the temperature.
4. After the programmed baking time, the oven will switch off, a beep will sound, and the [baking-time-symbol] [ → ] will flash rapidly.
5. Touch any sensor to turn off the beep and the [baking-time-symbol] [ → ]. The oven will restart.
6. Turn the function selection knob to the [off-position] (o) to turn off the oven.

The remaining baking time can be changed at any time by touching the [touch-sensor] or [plus-button] until the [baking-time-symbol] [ → ] flashes rapidly, then pressing [ok-button] to change the time.

Programming End Time

1. Touch the [touch-sensor] or [plus-button] until the [end-time-symbol] [ →l ] flashes. Press [ok-button]. The current time will be displayed.
2. Set the end time by pressing the [touch-sensor] or [plus-button]. A double beep confirms. The countdown starts, and the [end-time-symbol] [ →l ] will flash slowly.
3. Select the heating function and set the temperature.

Safety Instructions

Child Lock (Blokada uruchomienia)

This function can be activated at any time. To activate, press and hold the [ok-button] for a few seconds until a beep sounds and the [lock-symbol] [ ] appears. The electronic programmer is now locked.

If the oven is off and the child lock is active, the oven will not operate even if a heating function is selected. To deactivate, press and hold the [ok-button] for a few seconds until a beep sounds.

Manual Door Lock (Ręczna blokada drzwiczek)

Available only in pyrolytic models. This function allows locking the oven door.

To activate/deactivate the door lock:

1. Touch the [touch-sensor] or [plus-button] until the door lock status symbol flashes on the display. The display will show "ON" (active) or "OFF" (inactive).
2. Press the [ok-button]. A beep will sound, and the lock will be activated (if OFF) or deactivated (if ON).

Important: To unlock the door during a baking process, set the function selection knob to the [off-position] (o), then deactivate the door lock following the instructions above. After unlocking, turn the function knob back to the previous position to continue baking.

Teka Hydroclean® Function

This function easily removes grease and dirt stuck to the oven walls. For best results, avoid excessive accumulation of dirt and clean the oven regularly.

Programming Teka Hydroclean®

Important:

• The function can only be activated when the selection knobs are set to the [off-position] (o).
• After locking the door, you can start the baking process.
• To activate/deactivate the door lock, follow these steps:
  1. Touch the [touch-sensor] or [plus-button] until the door lock status symbol flashes on the display. The display will show "ON" (active) or "OFF" (inactive).
  2. Press the [ok-button]. A beep will sound, and the lock will be activated (if OFF) or deactivated (if ON).
• When the door is fully locked/unlocked, the door lock symbol [] will illuminate or disappear from the display.

Important: To unlock the door during a baking process, set the function selection knob to the [off-position] (o), then deactivate the door lock following the instructions above. After unlocking, turn the function knob back to the previous position to continue baking.

Teka Hydroclean® Process

To perform the cleaning:

1. When the oven is cold, place a cloth on the bottom of the oven cavity.
2. Carefully pour 200 ml of water into the oven cavity.

Information: For best cleaning results, add a teaspoon of mild dish soap to the water and pour it onto the cloth on the oven floor.

3. Set the function selection knob to the [off-position] (o).
4. A beep will sound, indicating the Teka Hydroclean® cleaning process has started. The [hydroclean-symbol] [] will flash slowly, and the remaining time will be displayed.

Important:

• The cleaning time cannot be changed. To interrupt the cycle before completion, set the function selection knob to the [off-position] (o).
• After the cleaning process is complete, the oven will switch off, a beep will sound, and the [hydroclean-symbol] [] will flash rapidly.

Important: Do not open the oven door until the Hydroclean® cleaning process is finished. The cooling phase is necessary for the function to work correctly.

6. Touch any sensor to turn off the beep and the [hydroclean-symbol] [].
7. Set the function selection knob to the [off-position] (o).
8. Now, remove residual water and dirt using a damp cloth.

The Hydroclean® cleaning function should be activated at a low temperature. The oven's cooling time depends on the ambient temperature.

Automatic Pyrolytic Cleaning Function

This function is available in pyrolytic HLB P models. It allows for a pyrolytic cleaning cycle where accumulated grease is incinerated at high temperatures.

It is generally recommended to perform pyrolytic cleaning every 4-5 baking cycles. The program duration adjusts based on the oven's dirt level; a dirtier oven requires a longer program.

During pyrolytic cleaning, the interior oven light remains off.

Programming Pyrolytic Cleaning Function

Important: Before using the pyrolytic function, remove all accessories (baking trays, racks, side supports, telescopic runners) from the oven. Follow the assembly and maintenance instructions for this.

1. Set the function selection knob to the [pyrolysis-symbol].
2. After a few seconds, the [pyrolysis-symbol] [] will illuminate on the display, showing "P2" (pyrolysis program 2).
3. Select the pyrolytic cleaning program (P1, P2, or P3) by pressing the [plus-button] or [touch-sensor].
   • P1: Short program, 1 hour duration.
   • P2: Standard program, 1.5 hours duration.
   • P3: Long program, 2 hours duration.
4. Press [ok-button]. The automatic door lock will engage immediately.

[warning-icon] WARNING

Ensure the door is properly closed. If not, the door will not lock, and a beep will sound. If this occurs, turn off the beep by pressing any button on the electronic programmer, close the door correctly, set the function knob to the [off-position] (o), and repeat the pyrolytic cleaning program as per the instructions.

5. Once the door is locked, the [pyrolysis-symbol] [] will illuminate, and the remaining time for the pyrolysis cycle will be displayed.

Important: The pyrolytic cleaning program has started. During this time, the electronic programmer cannot be used, except for the child lock function. Do not open the oven door to avoid interrupting the cleaning process.

6. When the pyrolytic cleaning program finishes, a beep will sound, the [pyrolysis-symbol] [] will flash, and the display will show "0:00".
7. Press any button on the electronic programmer to turn off the beep.
8. Set the function selection knob to the [off-position] (o).
9. The heating phase is complete, but the oven is still very hot and cannot be used.

Pyrolytic Cooling and Post-Cleaning

The cooling process will begin. The [cooling-symbol] [] will remain illuminated until the oven has completely cooled down.

Important: Due to the high internal temperature, the cooling time depends on the ambient temperature.

1. When the oven has cooled, the [cooling-symbol] [] will disappear.
2. Open the oven door and remove the ash residue using a damp cloth. Use a nylon kitchen sponge for hard-to-reach areas.
3. Once the oven cavity is clean, reinsert all accessories (baking trays, racks, side supports, telescopic runners).
4. The oven is now ready for use.

Important: If you encounter any problems during the activation or duration of the pyrolytic cleaning program, consult the assembly and maintenance manual.

Cancelling the Pyrolytic Cleaning Function

Pyrolysis is an automatic function set via the electronic programmer. To cancel a pyrolytic cleaning program, reset the device as follows:

1. Set the function selection knob to the [off-position] (o). The display will show "00:00".
2. Depending on the internal temperature, one of two situations may occur:
   • a) Unsafe internal temperature: The door will remain locked until a safe temperature is reached.
   • b) Safe internal temperature: If the internal temperature is safe, the door will unlock immediately.
3. After the door unlocks, the current time will reappear on the display.

Energy Efficiency Information

The following table summarizes the energy efficiency data for various Teka oven models:

Note: Energy consumption values are based on the EU energy label regulations (65/2014). Specific details regarding cycle types are available in the original PDF.