Installation and Mounting Manual for EK-Vector RTX Aorus 2080 Ti Backplate

Introduction

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Step 1: General Information

Sample picture of Gigabyte GeForce RTX 2080 Ti graphics card.

Image of a Gigabyte GeForce RTX 2080 Ti graphics card, showcasing its complex PCB layout, heatsink, and I/O ports.

Step 2: Preparing Your Graphics Card

The EK-Vector RTX Aorus 2080 Ti backplate is designed for straightforward installation. First, ensure the EK-Vector RTX Aorus 2080 Ti series water block is installed according to its manual. If the water block is already installed, refer to the diagram below to identify which mounting screws should remain and which should be removed. Please remove the six (6) M2.5x4 AX1 screws and their associated PVC washers (marked with arrows in the diagram).

Diagram showing the underside of a graphics card with arrows indicating six specific screws (M2.5x4 AX1) and their accompanying PVC washers that need to be removed from designated mounting points. The text 'Vector Aorus' is visible on the card.

Step 3: Applying the Thermal Pads

The EK-Vector RTX Aorus 2080 Ti features passive cooling for the printed circuit board (PCB) and its components. It is mandatory to install the enclosed thermal pads. Please install the 1.5mm thick thermal pad (Thermal Pad F – 1.5mm (120x16)) and the 2mm thick thermal pad (Thermal Pad F – 2mm (120x16)) as shown in the picture below. You may need to trim any excess thermal pad material.

Layout diagram for thermal pad placement on the EK-Vector RTX Aorus 2080 Ti backplate. It highlights three areas: two marked '1.' for 1.5mm thermal pads and one marked '2.' for a 2mm thermal pad, corresponding to specific components on the graphics card's PCB.

Thermal Pad Specifications:

• 1. Thermal Pad F – 1.5mm (120x16mm)
• 2. Thermal Pad F – 2mm (120x16mm)

Step 4: Attaching EK-Vector RTX Aorus 2080 Ti to the Graphics Card

Take the enclosed mounting screws and install them as shown in the picture below. Use six (6) M2.5x7 AX1 screws and tighten them using a Philips head screwdriver.

HINT: Do not fully tighten screws until they are all positioned in their mounting holes. The backplate has milled-in standoffs, so there is no risk of over-tightening the screws. Nevertheless, do not use excessive force, as it is not necessary.

This product is intended for use only with EK-Vector RTX Aorus 2080 Ti series water blocks. No other 3rd party heat sinks or coolers are officially supported by EK, and EK does not offer any assistance or support for such applications.

Illustration of the EK-Vector RTX Aorus 2080 Ti backplate being attached to the graphics card. Six M2.5x7 AX1 screws are shown being inserted into mounting holes, with arrows indicating their positions. The text 'M2.5x7 AX1' is clearly labeled.

Important Disclosures

VERY IMPORTANT NOTICE:

Once the installation is completed, it is recommended practice to test the cooling circuit for leaks prior to powering up the computer. We recommend a 24-hour leak test before powering up the computer. Do not test the water block using city water pressure, as this can rupture the top of the housing and render the block unusable (and will void your warranty). While all efforts have been made to provide the most comprehensive tutorial possible, EK Water Blocks assumes no liability, expressed or implied, for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.

Warranty

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this period, products will be repaired or have parts replaced at EK Water Blocks' discretion, provided that: (I) the product is returned to the agent from whom it was purchased; (II) the product has been purchased by an end user and has not been used for commercial purposes; (III) the product has not been misused, handled carelessly, or used in a manner other than in accordance with the instructions provided describing its installation and proper use.

This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer.

This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids. EK blocks are sealed with a warranty void circular label, which proves that the block has withstood a pressure leak test. Removing this label will void the leak-free guarantee, but not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

Required Tools and Mounting Screws

• Philips head screwdriver
• Scissors