Caséta Wireless In-Wall Switch Quick-Start Guide

Contents Supplied

• In-wall switch (PD-5ANS, PD-6ANS)
• Jumper wire
• Wire connectors (5)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Pliers
• Phillips-head screwdriver

Installing Your Switch

Installation for lights with one wall switch (single-pole)

1. Step 1: Turn Power Off

   Turn power off at the circuit breaker! ⚠️ SHOCK HAZARD

   [Diagram: Hand turning off a circuit breaker switch.]

   May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

2. Step 2: Remove Existing Switch

   Remove the wallplate from the switch.

   Remove the switch and pull it away from the wall.

   [Diagram: Removing wall plate, then switch from wall box.]

3. Step 3: Remove Side Sections (If Necessary)

   Bend back and forth to remove side sections. Do not remove outside side sections on switches at the end of a gang.

   [Diagram: Bending and breaking side sections. Note: Do not remove outside sections on end-of-gang switches.]

4. Step 4: Disconnect Wires

   Disconnect all wires* from the switch.

   [Diagram: Wires disconnected: ground, load, hot, neutral, blue wire.]

   Contractor Note: For wiring diagrams, please visit www.casetawireless.com/wiring.

   Important Note: Some lights have one wall switch, while others have two or more (e.g., stair lights). This guide covers single-pole installation. For 3-way installations, visit www.casetawireless.com/3way for complete instructions and videos.

5. Step 5: Note Wires

   Identify the hot, load, neutral, and ground wires.

   [Diagram: Highlighting hot, load, neutral, ground wires.]

   Important Note: Removing side sections reduces the switch's maximum wattage rating. See the chart below for maximum load information.

   Maximum Load Derating Chart (120 V~ 50/60 Hz)

   Model	Side sections removed			Load Type
   	None	1 side	2 sides
   PD-5ANS	5 A	5 A	5 A	LED, & Fluorescent¹
   PD-6ANS	6 A	6 A	5 A	LED, & Fluorescent¹
   PD-5ANS	600 W			Incandescent, Halogen, & ELV
   PD-6ANS	720 W			Incandescent, Halogen, & ELV
   PD-5ANS	600 VA			MLV²
   PD-6ANS	720 VA			MLV²
   PD-5ANS	3 A	3 A	3 A	General Purpose Fan
   PD-6ANS	3.6 A	3.6 A	3.6 A	General Purpose Fan

   ¹ The in-wall switch is UL Listed for use with all magnetic and electronic fluorescent ballasts.

   ² The maximum lamp wattage is determined by the efficiency of the transformer (70%-85% typical). For actual transformer efficiency, contact the fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the in-wall switch.

   *If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way.

6. Step 6: Connect the Switch

   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the switch using a wire connector.
   2. Connect the load wire from the wallbox to the red wire on the switch using a wire connector.
   3. Connect the hot wire from the wallbox to the black wire on the switch using a wire connector.
   4. Connect the neutral wire from the wallbox to the white wire on the switch (neutral connection required).
   5. Cap the blue wire with a wire connector.*

   [Diagram: Wire connections: Ground to green, load to red, hot to black, neutral to white. Blue wire capped.]

   *Note: The blue wire is only used in 3-way installations. See www.casetawireless.com/3way for more information.

7. Step 7: Mount the Switch

   Use the screws provided.

   [Diagram: Screwing switch into wall box.]

8. Step 8: Attach the Wallplate

   Attach the adapter to the switch using the screws provided and snap on the wallplate.

   [Diagram: Attaching adapter and snapping wall plate. Note: Multi-gang wallplate may be needed.]

9. Step 9: Turn Power On

   Turn power on at the circuit breaker.

   [Diagram: Hand turning on circuit breaker switch.]

CAUTION: Use only with permanently installed lighting loads or with general purpose fan loads.

Codes: Install in accordance with all national and local electrical codes.

Grounding: When no "grounding means" exist in wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.

FCC/IC Information: This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Warranty: For warranty information, please visit www.casetawireless.com/warranty.

Supported Loads (120 V~)

• PD-5ANS: LED--up to 5 A; Incandescent/Halogen--up to 600 W; MLV--up to 600 VA; ELV--up to 600 W; Fluorescent--up to 5 A; General Purpose Fan--up to 3 A
• PD-6ANS: LED--up to 6 A; Incandescent/Halogen--up to 720 W; MLV--up to 720 VA; ELV--up to 720 W; Fluorescent--up to 6 A; General Purpose Fan--up to 3.6 A

Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A.

Using Your Caséta Wireless Kit (Sold Separately)

With a Smartphone or Tablet (Smart Bridge Required)

The Caséta Wireless switch can be controlled from a smartphone when used with the Lutron Smart Bridge. All devices must be within 30 ft (9 m) from the Lutron Smart Bridge.

If you are using the switch and remote control with the Lutron Smart Bridge, follow the instructions below. Note: If using with another manufacturer's bridge, refer to that manufacturer's instructions.

1. Step 1: Download the Lutron App

   Search for "Lutron Caseta" on the App Store or Google Play.

   [Diagram: App Store icon, Google Play icon, Lutron app logo.]

   www.casetawireless.com/LutronApp

2. Step 2: Launch the Lutron App

   The Lutron app will guide you through setting up your devices.

   [Diagram: Phone screen showing Lutron app interface.]

3. Step 3: Use the Lutron App for All Remaining Steps

   Add devices, control lights, schedule, and connect while away.

   [Diagram: App interface showing device options.]

Without a Smartphone or Tablet (Smart Bridge Not Required)

Pairing the Switch and Pico Remote Control

1. Press and hold "off" button on the switch

   Hold for 6 seconds until the LED starts blinking.

   [Diagram: In-wall switch, "off" button highlighted, LED indicator blinking.]

2. Press and hold "off" button on the remote

   Hold for 6 seconds until lights flash 3 times. ✔️ Pairing successful.

   [Diagram: Pico remote, "off" button highlighted, indicator lights flashing 3 times.]

   Repeat steps to pair other Pico remote controls.

Using Your Controls:

In-wall switch: ON/OFF buttons, FASS (Front Accessible Service Switch).

Replacing light bulbs using FASS: Pull the FASS out on the in-wall switch to remove power at the light socket.

[Diagram: In-wall switch with ON/OFF buttons and FASS feature. FASS being pulled out.]

Troubleshooting

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

For advanced features, tips for using Caséta Wireless products with LEDs, the complete Caséta Wireless product line, and more, please visit www.casetawireless.com/features.

Device Ratings

In-wall switch: PD-5ANS, PD-6ANS

120 V~ 50/60 Hz

Trademarks

Lutron, Lutron, Caséta, and Pico are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. FASS and are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Google and the Google logo are registered trademarks of Google Inc., used with permission. ©2014-2017 Lutron Electronics Co., Inc.