Roborock Qrevo Plus Robot Vacuum Parts and Setup Guide
Parts Identification
The following sections identify the various components of the Roborock Qrevo Plus robot vacuum and its associated auto-empty dock.
Robot Vacuum Components
- A1: Robot Vacuum Overview (Top View)
- A1-1: Power Button [?]
- A1-2: Docking Sensor [?]
- A2: Robot Vacuum Overview (Bottom View)
- A2-1: Cliff Sensor [⬇️]
- A2-2: Wall Sensor [?]
- A2-3: Omni-directional Wheel [?]
- A2-4: Side Brush Module [?]
- A2-5: Charging Contacts [⚡]
- A2-6: Main Brush Cover Latch [?]
- A2-7: Main Brush Cover [?️]
- A2-8: Drive Wheel [⚙️]
- A2-9: Dustbin Release Latch [➡️]
- A3: Robot Vacuum Overview (Front/Side View)
- A3-1: LiDAR Navigation Sensor [?️]
- A3-2: Bumper [?]
- A3-3: Infrared Docking Sensor [ infrared ?]
- A3-4: Dustbin [?️]
- A3-5: Water Tank [?]
- A3-6: Mop Module Attachment Point [?]
- A3-7: Rear Wheel [⚙️]
- A3-8: Power Port [?]
- A3-9: Speaker [?]
- A3-10: Control Buttons [▶️ ⏸️ ?] (Play/Pause, Home)
- A3-11: LED Indicator [?]
- A3-12: Microphone [?]
- A3-13: Air Outlet [?]
- A4: Main Brush Module
- A4-1: Main Brush [?]
- A4-2: Main Brush Cover [?️]
- A5: Filter [?]
- A6: Dustbin
- A6-1: Dustbin Lid [⬆️]
- A6-2: Filter [?]
- A6-3: Dustbin Body [?️]
- A6-4: Release Button [➡️]
- A7: Mop Pad Holder [?]
- A8: Power Cable [?]
Auto-Empty Dock Components
- A9: Auto-Empty Dock [?]
- A10: Auto-Empty Dock Components
- A10-1: Dust Bag Compartment [?]
- A10-2: Dust Bag [?]
- A10-3: Dust Bag Release Latch [➡️]
- A10-4: Dust Outlet [?]
- A10-5: Docking Station [?]
- A10-6: Robot Charging Contacts [⚡]
- A10-7: Robot Docking Sensor [?]
- A10-8: Water Tank [?]
- A10-9: Water Pump [?]
- A10-10: Mop Cleaning Station [?]
- A10-11: Mop Holder [?]
- A10-12: Mop Drying Fan [?]
- A10-13: Clean Water Tank [?]
- A10-14: Dirty Water Tank [?]
- A10-15: Water Level Sensor [?]
- A10-16: Filter [?]
- A10-17: Air Inlet [?]
- A10-18: Dust Outlet [?]
- A10-19: Docking Sensor [?]
- A11: Auto-Empty Dock (Rear/Side View)
- A11-1: Power Port [?]
- A11-2: Air Filter [?]
- A11-3: Dust Outlet [?]
Setup and Maintenance
Follow these steps for setting up and maintaining your Roborock Qrevo Plus.
Dock Placement (B1)
- B1-1: Recommended placement: Open area, away from obstacles, with sufficient clearance. [✅]
- B1-2: Avoid placement near stairs or areas with significant drop-offs. [❌]
Docking Station Setup (B2)
- B2-1: Connect power cable to dock. [?]
- B2-2: Place dock against a wall with adequate clearance around it. [?]
- B2-3: Connect power cable to wall outlet. [⚡]
- B2-4, B2-5: Ensure the robot can dock with the station. [➡️ ?]
Docking Station with Mop Cleaning (B3)
- B3-1: The docking station supports mop cleaning and drying. [? ?]
- B3-2: Location for filling the clean water tank. [?]
- B3-3: Location for removing the dirty water tank. [?️]
Auto-Empty Dock Dustbin Compartment (B4)
- B4-1: Access to the dust bag compartment. [?]
Installing Dust Bags (C1)
Open the dustbin lid on the auto-empty dock and insert a new dust bag. [⬆️ ?]
Installing Mop Pads (C2)
- C2-1: Mop pad holder. [?]
- C2-2: Mop pad. [?]
- C2-3: Attach the mop pad to the holder. [➡️ ?]
- C2-4: Mop pad holder with attached mop pad. [?]
Installing Main Brush (D1)
- D1-1 to D1-4: Components related to the main brush assembly.
- D1-5: Main brush. [?]
- D1-6: Remove the old main brush by lifting it out. [➡️ ?]
- D1-7: Insert the new main brush, ensuring it clicks into place. [⬅️ ?]
- D1-8: Secure the main brush. [?]
- D1-9: Close the main brush cover. [?️]
Replacing Side Brush (D2)
Replace the side brush by unscrewing the old one and attaching the new one. [? ?]
Cleaning Main Brush (D3)
- D3-1: Remove the main brush. [➡️ ?]
- D3-2: Clean the brush under running water. [? ?]
Cleaning Robot Body (D4)
Wipe the robot's exterior with a dry cloth. [?]
Cleaning Dustbin (D5)
- D5-1: Remove the dustbin from the robot. [➡️ ?️]
- D5-2: Empty the dustbin's contents into a trash receptacle. [?️ ➡️ ?️]
- D5-3: Clean the dustbin. [?]
- D5-4: Ensure the dustbin is completely dry before reinserting. [☀️]
Cleaning/Replacing Filter (D6)
- D6-1: Remove the filter from the dustbin. [➡️ ?]
- D6-2: Clean the filter under running water. [? ?]
- D6-3: Allow the filter to dry completely. [☀️]
Cleaning Mop Pads (D7)
- D7-1: Remove the mop pads from the holder. [➡️ ?]
- D7-2: Clean the mop pads. [?]
Cleaning Dock Sensors and Contacts (D8)
- D8-1 to D8-4: Indicate locations of sensors on the dock.
- D8-5: Clean the dock's sensors using a dry cloth. [? ?]
- D8-6: Clean the charging contacts on both the dock and the robot. [? ⚡]
Docking Robot Correctly (D9)
- [✅] Robot correctly aligns and docks with the auto-empty station.
- [❌] Robot is misaligned or obstructed, preventing proper docking.
Emptying Dock Dust Bag (D10)
Remove the dust bag from the auto-empty dock's compartment. [➡️ ?]
Installing Robot onto Dock (D11)
Align the robot with the charging contacts and docking guides on the auto-empty station. [➡️ ? ⚡]
Filling Clean Water Tank (D12)
- D12: Remove the clean water tank from the dock. [➡️ ?]
- D12-1: Open the fill port on the tank. [⬆️]
- D12-2: Fill the tank with clean water. [?]
- D12-3: Close the fill port securely. [⬇️]
- D12-4: Reinsert the filled clean water tank into the dock. [⬅️ ?]
Emptying Dirty Water Tank (D13)
- D13: Remove the dirty water tank from the dock. [➡️ ?]
- D13-1: Open the lid of the dirty water tank. [⬆️]
- D13-2: Empty the dirty water into a suitable receptacle. [? ➡️ ?️]
- D13-3: Close the lid securely. [⬇️]
