MTD TB90BC 2-Cycle Gas Trimmer/Brushcutter Parts
Engine Parts
This section details the engine components for the MTD TB90BC 2-cycle gas trimmer/brushcutter. The diagram shows an exploded view of the engine assembly with numbered parts corresponding to the list below.
Item | Part No. | Description |
---|---|---|
1 | 753-1192 | Air Cleaner/Muffler Cover Assembly (includes 2 & 41) |
2 | 791-180350B | Air Cleaner Filter |
3 | 791-180351 | Carburetor Mounting Screw Assembly |
4 | 753-1193 | Choke Extension |
5 | 753-1194 | Choke Plate |
6 | 753-1195 | Carburetor Assembly W/Limiter Caps (includes 7 & 18) |
7 | 791-610675 | Carburetor Gasket |
8 | 791-181860 | Carb Mount Screw |
9 | 791-181801 | Primer and Hose Assembly |
10 | 791-182063 | Carb Mount Assembly (includes 8) |
11 | 791-684451 | Reed Assembly |
12 | 791-182790 | Power Shaft Assembly |
13 | 753-1208 | Carburetor Mount Gasket |
14 | 791-182807 | Crank Case Service Assembly (includes 10, 12 & 22) |
15 | 791-612134 | Rear Mounting Pad |
16 | 753-1198 | Fuel Tank Assembly (includes 17-19) |
17 | 791-182612 | Fuel Cap Assembly |
18 | 791-181168 | Fuel Return Line |
19 | 791-682039 | Fuel Line Assembly |
20 | 791-145308 | Front Mounting Pad |
21 | 791-153520 | Shroud Assembly |
22 | 791-181861 | Shroud Screw |
23 | 791-182064 | Shroud Extension and Stand |
24 | 791-181867 | Flywheel Assembly |
25 | 791-181065 | Spacer |
26 | 753-1199 | Recoil Pulley Assembly |
27 | 791-613102 | Recoil Spring |
28 | 753-1200 | Rope Guide |
29 | 791-181441 | Pulley Retainer |
30 | 791-181079 | Pull Handle |
31 | 791-613102 | Rope |
32 | 753-1201 | Pressure Plate Assembly |
33 | 7531202 | Plate Screw |
34 | 753-1203 | Starter Housing Assembly (includes 26-31 & 41) |
35 | 791-181862 | Housing Screw |
36 | 791-182368 | Clutch Washer |
37 | 791-182369 | Clutch Rotor Assembly |
38 | 791-153592 | Clutch Drum Assembly |
39 | 791-612468 | Spring |
40 | 753-1204 | Clutch Cover Assembly (includes 41-44) |
41 | 791-181345 | Cover Screw |
42 | 791-182519 | Anti-Rotation Screw |
43 | 753-04003 | Clamping Screw |
44 | 791-180217 | Clamping Nut |
45 | 791-182798 | Wire Leads and Sleeve |
46 | 791-611063 | Ground Tab |
47 | 753-1205 | Module Assembly |
48 | 791-610311B | Spark Plug |
49 | 791-182066 | Muffler Assembly (includes 50-52) |
50 | 791-182747 | Spark Arrestor Screen |
51 | 791-182065 | Exhaust Gasket |
52 | 791-147575 | Muffler Mounting Bolt Assembly |
53 | 753-1206 | Cylinder Assembly (includes 55) |
54 | 753-1207 | Piston and Rod Assembly |
55 | 753-1197 | Cylinder Gasket |
56 | 791-182723 | Cylinder Bolt |
* | 791-180090 | O.E.M. Carburetor Repair Kit (Zama) |
* | 791-180091 | Gasket Diaphragm Repair Kit (Zama) |
* | 753-1209 | Piston Ring Set |
* | 753-1210 | Short Block Assembly (includes 8, 12, 14, 22, 48, 51-56) |
* | 791-610309 | Crankcase Seal |
* | 791-181599 | Clutch Springs (Qty. 2) |
Boom and Trimmer Parts
This section details the boom and trimmer components for the MTD TB90BC 2-cycle gas trimmer/brushcutter. The diagram shows an exploded view of the trimmer assembly, including the boom, handle, gearbox, and cutting head, with numbered parts corresponding to the list below.
Item | Part No. | Description |
---|---|---|
1 | 182801 | Throttle Housing and Trigger Assembly (includes 2-4) |
2 | 182802 | Throttle Trigger Lock-Out |
3 | 182803 | Throttle Trigger |
4 | 182690 | Throttle Trigger Spring |
5 | 182539 | Switch Assembly (includes 6) |
6 | 182357 | Throttle Cable Assembly |
7 | 610327 | Harness Clip |
8 | 182309 | Upper Drive Shaft Housing Assembly |
9 | 181099 | J-Handle Assembly (includes 10 & 11) |
10 | 612831 | Grip |
11 | 612021 | Tube Closure |
12 | 683295 | Handle Bracket Assembly (includes 13-18) |
13 | 181811 | Screw |
14 | 181812 | Upper Handle Clamp |
15 | 181813 | Middle Handle Clamp |
16 | 181814 | Lower Handle Clamp |
17 | 181815 | Nut |
18 | 145569 | Anti-Rotation Screw |
19 | 181616 | Click-Link Coupler (includes 20-23) |
20 | 182057 | Screw |
21 | 181617 | Bolt |
22 | 181618 | Adjustment Knob |
23 | 181886 | Knob Retaining Nut |
24 | 180804 | Lower Drive Shaft Housing Assembly |
25 | 613300 | Lower Flexible Drive Shaft |
26 | 182200 | Shield Mount Screw Assembly |
27 | 182193 | 2 piece Gearbox Assembly (includes 28-30) |
28 | 182195 | Gearbox Mounting Hardware |
29 | 145569 | Anti-Rotation Screw |
30 | 182196 | Blade Driver |
31 | 147492 | Blade Shield/Shield Mount |
32 | 683304 | Shield Mounting Screw |
33 | 68299 | Shield and Blade Assembly (includes 34) |
34 | 682061 | Blade Assembly |
35 | 147490 | Retaining Washer |
36 | 612483 | Spool Shaft |
37 | 683301 | Outer Spool and Eyelet Assembly |
38 | 612026 | Retainer |
39 | 610636 | Spring |
40 | 147495 | Inner Reel |
41 | 180814 | Bump Head Knob Assembly |
42 | 145873 | 4-Tooth Blade |
43 | 181699 | Nut |
* | 180014 | Blade Retaining Kit (includes 35 & 43) |
* | 613226 | Locking Rod Tool |
* | 682075 | Shoulder Harness |
2 Piece Gearbox Assembly Parts – Item 27
Item | Part No. | Description |
---|---|---|
44 | 182191 | Left Housing |
45 | 182192 | Right Housing |
46 | 182194 | Pinion Gear Assembly |
47 | 182199 | Output Shaft Bushing |
48 | 182198 | Output Shaft Gear |
49 | 182197 | Output Shaft Assembly (includes 46 & 47) |
Optional Accessories
Part No. | Description |
---|---|
180120 | Replacement Line, 0.095 Diameter |
147345 | Reel and Line Assembly |
147498 | Bump Head Assembly (includes 36-41) |
147543 | Ryobi 2-Cycle Oil |