User Guide for ZKTECO models including: ProBio QR USB Host, ProBio QR, USB Host
2 User Registration 1.15m 0.5m 1.15m 0.5m 1.15m 0.5m For user heights between 1.5m to 1.8m, it is recommended to install the device at 1.15m height above ground (can be
Інструкції та ПЗ
File Info : application/pdf, 16 Pages, 2.45MB
DocumentDocumentQUICK START GUIDE
ProBio(QR)
Version: 1.0 Date: May 2021
Safety Precautions
Before installation, please read the following precautions carefully to prevent risks and dangers to this product, users and surroundings.
Do not expose to direct sunlight, water, dust and soot. Do not place any magnetic object near the product. Magnetic objects such as Magnet, CRT, TV, Monitor or Speaker may damage the device. Do not place the device next to any heating equipment.
Prevent water, drinks or chemicals leaking into the device. This product is not intended for use by children unless they are supervised. Do not drop or damage the device. Do not disassemble, repair or modify the device. Do not use the device for any purpose other than those specified. Remove dusts or dirts regularly. While cleaning, wipe dust off with a smooth cloth or towel instead of water. Contact your supplier in case of any problem!
1
User Registration
1) Recommended Standing Position
For user heights between 1.5m to 1.8m, it is recommended to install the device at 1.15m height above ground (can be modified according to the user's average height).
1.15m
0.5m
1.15m 1.15m
0.5m
0.5m
Recommended Procedures (as shown in the left image): During registration and verification procedures, the position of device should not be changed to ensure high verification preciseness. If it is necessary to move the device, its vertical height should not be changed.
2) Registration
a. During registration, it is required to adjust your upper body to fit your eyes into the green frame on the screen.
b. During verification, it is required to show your face in the center of the screen and fit your face into the green frame in the screen.
2
Device Overview
2.8" Touch Screen
190.8mm (7.51")
Doorbell
Camera Card Reading Area & QR Code Scanner
85mm (3.35")
Tamper Switch Terminal Block
USB Port Reset Button
103mm (4.05")
3
Speaker
Device Installation
Installation on the wall
Attach the mounting template sticker to the wall, and drill holes according to the mounting paper.
Fix the back plate on the wall using the wall mounting screws. Attach the device to the back plate. Fasten the device to the back plate with a security screw.
Fixing Hole
Fixing Hole
MPS201508
Mounting Positioning Sticker (only for your reference)
Instruction on using Mounting Positioning Sticker:
Before fastening the device, please stick this Mounting Positioning Sticker onto where you want to install the device, and then drill holes and lay cables according to the symbols on the sticker.
Baseline
Wiring Hole 10
11
12 Fixing Hole
Fixing Hole
13
1.15m recommended height from the ground
for facial terminal and 1.4m for finger vein
terminal, it can be adjusted according to
14
the staff height.
15
61mm(2.4") 129 mm (5.08")
1.15m
4
Power Connection
Without UPS
{ Auxiliary AUX In GND { BELLBell
BELL+ { Sensor SEN
{ GND Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{Ethernet
RJ45-1 RJ45-2 RJ45-3
RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
RS232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
With UPS (Optional)
GND
1
2
12V DC 12V DC
{ Auxiliary AUX In GND { BELLBell
BELL+ { Sensor SEN
{ GND Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{Ethernet
RJ45-1 RJ45-2 RJ45-3
RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
RS232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
GND
1 2
12V DC
12V DC
Recommended AC Adapter
Recommended AC Adapter: 12V, 3A To share the power with other devices, use an AC Adapter with higher current ratings.
5
Ethernet Connection
LAN Connection
Connect the device and the software over an Ethernet cable. An example is shown below:
{ Auxiliary AUX In GND { BELLBell
BELL+ { Sensor SEN
{ GND Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{Ethernet
RJ45-1 RJ45-2 RJ45-3
RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
RS232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
1 4
Default IP Address: 192.168.1.201 Subnet Mask: 255.255.255.0
8 7 6 5 4 3 2 1
RJ 45
ZKBioSecurity
IP Address: 192.168.1.61 Subnet Mask: 255.255.255.0
DESCRIPTION RJ45-1 RJ45-2 RJ45-3 RJ45-6
WIRE Yellow Green Red Black
Note: In LAN, the IP Addresses of the Server (PC) and the device must be in the same network segment when connecting to the ZKBioSecurity software. Click [Comm.] > [Ethernet] > [IP Address], enter the IP address and click [OK].
6
RS485 Connection
Rs485 Slave Reader Connection
{ Auxiliary AUX In GND { BELLBell BELL+
{ Sensor SEN { GND
Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{ RJ45-1 RJ45-2 Ethernet
RJ45-3 RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
Rs232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
1
7
1
8
DESCRIPTION WIRE
+12V
Red
GND
Black
IWD0
White
IWD1
Green
RLED
Blue
GLED
Gray
BEEP
Purple
DESCRIPTION WIRE
WD0
Green
WD1
White
GND
Black
RXD
Gray
TXD
Purple
GND
Black
485A
Blue
485B
Yellow
Do not use
Rs485 Slave Reader
DIP Settings
1. There are six DIP switches on the back of RS485 slave reader, switches 1 to 4 are for RS485 address, switch 5 is reserved, and switch 6 is for reducing noise on a long RS485 cable.
2. If the RS485 slave reader is powered from the terminal, the length of wire should be less than 100 meters or 330 ft.
3. If the cable length is more than 200 meters or 600 ft., the number 6 switch should be turned ON as shown below.
ON 123456
Distance: Less 200 meters
Distance: More than 200 meters ON
123456
7
Lock Relay Connection
The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (Normally Opened when powered) is connected with 'NO' and 'COM' terminals, and the NC Lock (Normally Closed when powered) is connected with 'NC' and 'COM' terminals. The power can be shared with the lock or can be used separately for the lock, as shown in the example with NC Lock below:
Device Not Sharing Power with the Lock
1
{ Auxiliary AUX In GND { BELLBell
BELL+ { Sensor SEN
{ GND Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{ RJ45-1 RJ45-2 Ethernet
RJ45-3 RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
RS232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
COM1
12V DC
12
GND
NC1 Sensor
12V DC
DESCRIPTION WIRE
AUX
Brown
GND
BELL-
Purple Green
BELL+
Orange
SEN
Yellow
GND
Red
BUT
Blue
NO1
White
COM1
Black
NC1
Gray
AL-
Black
AL+
Red
Do not use
! Do not reverse the polarities.
GND
GND
+ -
FR107 Diode
Normally Closed Lock
8
Lock Relay Connection
Device Sharing Power with the Lock
1
{ Auxiliary AUX In GND { BELLBell
BELL+ { Sensor SEN
{ GND Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{ RJ45-1 RJ45-2 Ethernet
RJ45-3 RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
RS232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
12
GND COM1
12V DC
1
7
DESCRIPTION WIRE
AUX
Brown
GND
BELL-
Purple Green
BELL+
Orange
SEN
Yellow
GND
Red
BUT
Blue
NO1
White
COM1
Black
NC1
Gray
AL-
Black
AL+
Red
DESCRIPTION +12V GND IWD0 IWD1 RLED GLED BEEP
WIRE Red Black White Green Blue Gray Purple
Do not use
! Do not reverse the polarities.
Sensor
GND GND
NC1
FR107 Diode
Normally Closed Lock 9
Standalone Installation
ZKBioSecurity
ZKBioSecurity
Electric Lock
Input Emergency Button
Door Sensor
USB Disk App Store Download
Ethernet
ProBio
Output ALARM
Alarm
No Touch
EXIT
Exit Button
% Output
Doorbell RS485/ Wiegand
Dynamic QR code
Card Reader
Google play
11
Wiegand Output Connection
{ Auxiliary AUX In GND { BELLBell
BELL+ { Sensor SEN
{ GND Button BUT
{ NO1
Lock COM1 NC1
{ ALAlarm
AL+
{ Power +12V Out GND { Wiegand IWD0
In IWD1 Red LED RLED Green LED GLED
Beep BEEP
{ RJ45-1 RJ45-2 Ethernet
RJ45-3 RJ45-6
{ WD0
Wiegand Out
WD1
GND
{ RXD
Rs232 TXD GND
{ 485A RS485
485B
{ +12V Power In
GND
1 8
DESCRIPTION WD0 WD1 GND RXD TXD GND 485A 485B
WIRE
Green White Black Gray Purple Black Blue Yellow
Do not use
WD1 WD0 GND
?
? ?
?B??E? E P ?G??L? ED ?W??D1 ?W??D0 ?G??N D ?+??1? 2 V
???
10
Device Operation
User Registration
When there is no Super Administrator set in the device, click on to enter the menu. Add a new user and set the User Role to Super Admin. The system will request the Administrator's verification before entering the menu. It is recommended to register a Super Administrator initially for security purposes.
Method 1: Register on the device
Tap on > [User Mgt.] > [New User] to register a new user.The options include entering the User ID and Name, setting User Role, registering Face, Card Number, Password, adding User Photo, and setting Access Control role.
Method 2: Register on ZKBioSecurity software
Please set the IP Address and Cloud Service Server Address in the Comm. menu option on the device. 1. Click[Access]>[Device]>[Device]>[Search]tosearchthedeviceonthesoftware.When an appropriate
Server Address and port is set on the device, the searched devices will be displayed automatically.
Refresh New Delete Export Search Control
Set up
Step 1
Search
View/Get
Communication
Search Total Progress
IP Address
No device found? Download Search Tools to Local Disk
Step 2
Searched devices count:1
Device Type
Serial Number
IP Address
MAC Address
192.168.163.201
Subnet Mask Gateway Address 255.255.255.0 192.168.163.201
Serial Number CJHC203336
Device Type Set Server ProBio
OperationsStep 3
Add
Add
Device Name
192.168.163.201
Icon Type Area
Door Area Name
Add to Level
Clear Data in the Device when Adding
The current systen communication port[iCs l6e6a0r9D, patleaaisnetmheakDeesvuirceetwhehdenevAicdediisnsge]t wcoilrlredcetlleyt.e data in the device(except event record), please use with caution!
Step 4
OK
Cancel
12
Device Operation
2. Click [Add] in the operation column, a new window will pop-up. Select the Icon type, Area, and Add to Level from each drop-down and click [OK] to add the device.
3. Click [Personnel] > [Person] > [New] and fill in all the required fields to register a new user in the software.
4. Click [Access] > [Device] > [Control] > [Synchronize All Data to Devices] to synchronize all the data to the device including the new users.
For more details, please refer the ZKBioSecurity User Manual.
Ethernet and Cloud Server Settings
Eg: 192.168.163.163
Eg: 192.168.163.1
Eg: 110.80.38.74 Eg: 6609
Click on > [COMM.] > [Ethernet] to set the network parameters. If theTCP/IP communication of the deviceissuccessful,theicon willbedisplayedintheupperrightcornerofthestandbyinterface. Click on > [COMM.] > [Cloud Server Setting] to set the Server Address and Server Port, the IP Address and Port Number of the server after the software is installed. If the device communicates with theServersuccessfully,theicon willbedisplayedintheupperrightcornerofthestandbyinterface.
Access Control Settings
Click on > [Access Control] to enter the access control management interface and set the relevant parameters of the access control.
13
Device Operation
QR Code as the Mobile Credential
The device can recognize the QR code image on the ZKBioSecurity Mobile APP captured by the QR code scanner, making it easy to access without contact. Please set the IP Address and Cloud Service Server Address in the COMM. menu option on the device.
1. Mobile APP Configuration After downloading and installing the , the user needs to set the Server before login. a. On the Server, choose [System] > [Authority Management] > [Client Register] to add
a registered App client. b. Open the App on the Smartphone. On the login screen, tap [Server Setting] and type the
IP Address or the Domain Name of the Server, and its Port Number. c. Tap the QR Code icon to scan the QR code of the new App client. After the client is identified
successfully, set the Client Name and tap [Testing Connection]. d. After the network is connected successfully, tap [Save].
2. Employee Mobile Login The Mobile Credential function is only valid when logging in as an employee. Tap on Employee to switch to Employee Login screen. Employees can login with the Personnel ID in [Personnel] > [Personnel] > [Person] and self-service password. The default selfservice password is 123456.
3. Scan the QR Code Find the access control QR code on the ZKBioSecurity Mobile App. Show the QR code to the QR code scanner of the device. The device prompts that the verification is successful. Note: 1. The user must have a card number registered in advance on the device or on the software. 2. When scanning, the QR code and the scanner must stay parallel at a distance of 15 to 30cm. For more details, please refer the ZKBioSecurity Mobile APP User Manual.
Mobile Credential
Eg: http://110.80.38.74 http://110.80.38.74 6609 Eg: 6609 4667D7 Mike
14
ZKTeco Industrial Park, No.32, Industrial Road, Tangxia Town, Dongguan, China. Tel: +86 769-82109991 Fax: +86 755-89602394 www.zkteco.com
Copyright©2021 ZKTECO CO., LTD. All rights reserved.
Acrobat Distiller 21.0 (Windows)