TP-Link Quick Installation Guide

Introduction

This guide demonstrates the setup process for the TP-Link TL-PA7017 KIT. The European version (TL-PA7017 KIT) is used for demonstration; actual products may differ.

Quick Installation

Follow these steps to set up your powerline network:

1. Step 1: Connect the first TP-Link TL-PA7017 adapter to your router via an Ethernet cable and plug it into a wall outlet. Ensure it's on the same electrical circuit as the other adapter.

   Diagram Description: A router is connected via an Ethernet cable to the first TL-PA7017 adapter, which is plugged into a wall outlet labeled 'Internet'.

2. Step 2: Plug the second TL-PA7017 adapter into another wall outlet on the same electrical circuit. Connect your device (e.g., a computer) to this adapter via an Ethernet cable.

   Diagram Description: The second TL-PA7017 adapter is plugged into a wall outlet, and a laptop is connected to it via an Ethernet cable.

3. Step 3: Wait until the Powerline LED on the adapter turns on. If the LED is off, refer to FAQ-Q2.

   Visual Indicator: Powerline LED solid on.

4. Step 4: Enjoy your new powerline network connection.

   Visual Indicator: Text '4 Enjoy!'

Attention: Always plug powerline devices directly into wall outlets, not into power strips.

Diagram Description: A visual comparison showing a powerline device plugged into a 'Wall Outlet' (correct) versus a 'Power Strip' (incorrect).

Adding More Devices: To extend your network, simply plug additional TP-Link powerline adapters or extenders into wall sockets on the same electrical circuit.

Set Up a Secure Powerline Network by Pairing (Recommended)

You can create or join a secure powerline network by pairing two devices at a time. It is recommended to plug the powerline devices near each other when pairing.

To Create a Secure Powerline Network:

1. Press the Pair button on one powerline device for 1 second. Its Power LED should start blinking. (If the Power LED does not blink, press the Pair button again.)
2. Within 2 minutes, press the Pair button on another device for 1 second. Its Power LED should start blinking.
3. When the Powerline LED lights up solid, a powerline network has been successfully created.

Diagram Description: Shows two adapters. First adapter's Pair button pressed, Power LED blinking. Within 2 minutes, second adapter's Pair button pressed, Power LED blinking. Finally, both adapters show solid Powerline LEDs.

To Join an Existing Secure Powerline Network:

1. Press the Pair button on any of the existing powerline devices for 1 second. Its Power LED starts blinking. (If the Power LED does not blink, press the Pair button again.)
2. Within 2 minutes, press the Pair button on the new powerline adapter for 1 second. Its Power LED starts blinking.
3. When the Powerline LED turns on solid, the process is complete.

Diagram Description: Shows an existing powerline device with its Pair button pressed (Power LED blinking). Within 2 minutes, a new powerline device's Pair button is pressed (Power LED blinking). Finally, the new adapter shows a solid Powerline LED.

Physical Appearance

LED Indicators:

Buttons:

Pair Button:

• Press and hold for 1 second to set up or join a secure powerline network.
• Press and hold for more than 6 seconds to reset the powerline adapter.

Frequently Asked Questions

Q1. How do I reset my powerline adapter?

With the powerline adapter plugged into an electrical outlet, press and hold the Pair button for more than 6 seconds until the Power LED goes off momentarily and then comes back on.

Q2. What should I do if the Powerline LED is off?

• Try another wall socket and ensure all powerline devices are on the same electrical circuit.
• Try to set up a powerline network by pairing. Refer to the "Set Up a Secure Powerline Network by Pairing" section for instructions.
• If the problem persists, contact TP-Link Technical Support.

Q3. What should I do if there is no internet connection in my powerline network?

• Make sure all powerline devices are on the same electrical circuit.
• Ensure the Powerline LEDs are lit on all your powerline devices. If not, pair all devices again.
• Verify that all devices are correctly and securely connected.
• Check your internet connection by connecting a computer directly to the modem or router.

Q4. What should I do if a successfully-paired powerline device does not reconnect after it is relocated?

• Try another socket and confirm it is on the same electrical circuit.
• Attempt to pair the device again, ensuring the Powerline LED is on.
• Check for potential interference from household appliances (e.g., washing machine, air conditioner) that might be too close to a powerline device. If your powerline device has an integrated electrical socket, plug the interfering appliance into it to filter out electrical noise.

Easy Management

For advanced configuration, use the tpPLC utility:

1. Visit https://www.tp-link.com and search for your product.
2. Find and download the compatible version of the utility from the product's Support page.
3. Install the utility and begin your configuration.

For technical support, the user guide, and other information, please visit https://www.tp-link.com/support.

Compliance and Safety Information

TP-Link declares that this device complies with essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, and 2011/65/EU. The original EU declaration of conformity can be found at https://www.tp-link.com/en/ce.

Safety Precautions:

• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device.
• Do not use a damaged charger or USB cable to charge the device.
• The socket-outlet should be installed near the equipment and be easily accessible.
• For passthrough devices, plug power strips into the integrated electrical sockets, but avoid stacking devices of the same or different types during normal use.
• Always plug powerline devices directly into wall outlets, not power strips.

Please read and follow the above safety information when operating the device. TP-Link cannot guarantee that accidents or damage will not occur due to improper use. Use this product with care and at your own risk.